Download or read book Materials Engineering in Turbines and Compressors written by Institute of Materials and published by . This book was released on 1995 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Materials Engineering in Turbines and Compressors written by R. D Conroy and published by . This book was released on 1995 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Development of Gas Turbine Materials written by G.W. Meetham and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: The turbine has many advantages over other prime movers for producing power. The first turbine used water as the working fluid and this principle is still used in hydro-electric power generation. The steam turbine was developed late in the nineteenth century and was first applied to marine propulsion by Parsons in 1897. Since that time it has become the most widely used prime mover in electricity generation and marine propulsion. The equipment required to generate steam is bulky however and it was realised that much more compact power plant could be designed if the hot gases used for steam generation could drive the turbine directly. Early attempts to produce gas turbines were unsuccessful for several reasons, one major problem being that materials with the capability of operating at sufficiently high stresses and temperatures were not available. Following the first experimental Whittle engine in 1937, the emphasis on the development of the gas turbine engine for aircraft propulsion during World War II changed this situation dramatically. Gas turbine powered civil aircraft entered airline service in the early 1950s and gas turbines also began to compete successfully in other fields. Apart from the aircraft market, they have been used widely in pumping sets for oil and gas transmission pipelines and peak load electricity generation. Use in warship propulsion is increasing and there is currently major activity, in the USA in particular, in developments for vehicular propulsion.
Download or read book Materials Engineering in Turbines and Compressors written by R.D. Conroy and published by . This book was released on 1995 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fluid Mechanics and Thermodynamics of Turbomachinery written by S. Larry Dixon and published by Elsevier. This book was released on 2005-03-30 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: The new edition will continue to be of use to engineers in industry and technological establishments, especially as brief reviews are included on many important aspects of Turbomachinery, giving pointers towards more advanced sources of information. For readers looking towards the wider reaches of the subject area, very useful additional reading is referenced in the bibliography. The subject of Turbomachinery is in continual review, and while the basics do not change, research can lead to refinements in popular methods, and new data can emerge. This book has applications for professionals and students in many subsets of the mechanical engineering discipline, with carryover into thermal sciences; which include fluid mechanics, combustion and heat transfer; dynamics and vibrations, as well as structural mechanics and materials engineering. - An important, long overdue new chapter on Wind Turbines, with a focus on blade aerodynamics, with useful worked examples - Includes important material on axial flow compressors and pumps - Example questions and answers throughout
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2017-09-01 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. - Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers - A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field - The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems
Download or read book Worked Examples in Turbomachinery written by S. L. Dixon and published by Elsevier. This book was released on 2014-05-23 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: Worked Examples in Turbomachinery (Fluid Mechanics and Thermodynamics) is a publication designed to supplement the materials in Fluid Mechanics, Thermodynamics of Turbomachinery, Second Edition. The title provides detailed solution for the unanswered problems from the main textbook. The text first covers dimensional analysis, and then proceeds to tackling thermodynamics. Next, the selection discusses two-dimensional cascades. The text also talks about axial flow turbines and compressors, along with the three-dimensional flow in axial turbo machines. Chapter 7 covers centrifugal compressor and pumps, while Chapter 8 tackles radial flow turbines. The book will be of great use to students of mechanical engineering, particularly those who have access to the main textbook.
Download or read book The Chemical Engineering Guide to Compressors written by Richard Greene and published by . This book was released on 1984 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Principles of Turbomachinery written by R. K. Turton and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 213 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text outlines the fluid and thermodynamic principles that apply to all classes of turbomachines, and the material has been presented in a unified way. The approach has been used with successive groups of final year mechanical engineering students, who have helped with the development of the ideas outlined. As with these students, the reader is assumed to have a basic understanding of fluid mechanics and thermodynamics. However, the early chapters combine the relevant material with some new concepts, and provide basic reading references. Two related objectives have defined the scope of the treatment. The first is to provide a general treatment of the common forms of turbo machine, covering basic fluid dynamics and thermodynamics of flow through passages and over surfaces, with a brief derivation of the fundamental governing equations. The second objective is to apply this material to the various machines in enough detail to allow the major design and performance factors to be appreciated. Both objectives have been met by grouping the machines by flow path rather than by application, thus allowing an appreciation of points of similarity or difference in approach. No attempt has been made to cover detailed points of design or stressing, though the cited references and the body of information from which they have been taken give this sort of information. The first four chapters introduce the fundamental relations, and the suc ceeding chapters deal with applications to the various flow paths.
Download or read book Gas Turbine Design Components and System Design Integration written by Meinhard T. Schobeiri and published by Springer. This book was released on 2017-06-06 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book written by a world-renowned expert with more than forty years of active gas turbine R&D experience comprehensively treats the design of gas turbine components and their integration into a complete system. Unlike many currently available gas turbine handbooks that provide the reader with an overview without in-depth treatment of the subject, the current book is concentrated on a detailed aero-thermodynamics, design and off-deign performance aspects of individual components as well as the system integration and its dynamic operation.This new book provides practicing gas turbine designers and young engineers working in the industry with design material that the manufacturers would keep proprietary. The book is also intended to provide instructors of turbomachinery courses around the world with a powerful tool to assign gas turbine components as project and individual modules that are integrated into a complete system. Quoting many statements by the gas turbine industry professionals, the young engineers graduated from the turbomachinery courses offered by the author, had the competency of engineers equivalent to three to four years of industrial experience.
Download or read book Handbook of Turbomachinery written by Earl Logan, Jr. and published by CRC Press. This book was released on 2003-05-01 with total page 927 pages. Available in PDF, EPUB and Kindle. Book excerpt: Building on the success of its predecessor, Handbook of Turbomachinery, Second Edition presents new material on advances in fluid mechanics of turbomachinery, high-speed, rotating, and transient experiments, cooling challenges for constantly increasing gas temperatures, advanced experimental heat transfer and cooling effectiveness techniques, and propagation of wake and pressure disturbances. Completely revised and updated, it offers updated chapters on compressor design, rotor dynamics, and hydraulic turbines and features six new chapters on topics such as aerodynamic instability, flutter prediction, blade modeling in steam turbines, multidisciplinary design optimization.
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2011-12-12 with total page 993 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chapter 1: Overview of Gas Turbines -- Chapter 2: Theoretical and Actual Cycle Analysis -- Chapter 3: Compressor and Turbine Performance Characteristics -- Chapter 4: Performance and Mechanical Standards -- Chapter 5: Rotor Dynamics -- Chapter 6: Centrifugal Compressors -- Chapter 7: Axial-Flow Compressors -- Chapter 8: Radial-Inflow Turbines -- Chapter 9: Axial-Flow Turbines -- Chapter 10: Combustors -- Chapter 11: Materials -- Chapter 12: Gas Clean Up System -- Chapter 13: Bearings and Seals -- Chapter 14: Gears -- Chapter 15: Lubrication -- Chapter 16: Spectrum Analysis -- Chapter 17: Balancing -- Chapter 18: Couplings and Alignment -- Chapter 19: Control Systems and Instrumentation -- Chapter 20: Gas Turbine Performance Test -- Chapter 21: Maintenance Techniques -- Chapter 22: Case Studies -- Appendix: Equivalent Units.
Download or read book Fluid Mechanics and Thermodynamics of Turbomachinery written by S. Larry Dixon and published by Butterworth-Heinemann. This book was released on 2010-02-17 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbomachinery is a challenging and diverse field, with applications for professionals and students in many subsets of the mechanical engineering discipline, including fluid mechanics, combustion and heat transfer, dynamics and vibrations, as well as structural mechanics and materials engineering. Originally published more than 40 years ago, Fluid Mechanics and Thermodynamics of Turbomachinery is the leading turbomachinery textbook. Used as a core text in senior undergraduate and graduate level courses this book will also appeal to professional engineers in the aerospace, global power, oil & gas and other industries who are involved in the design and operation of turbomachines. For this new edition, author S. Larry Dixon is joined by Cesare Hall from the University of Cambridge, whose diverse background of teaching, research and work experience in the area of turbomachines is well suited to the task of reorganizing and updating this classic text. - Provides the most comprehensive coverage of the fundamentals of turbomachinery of any text in the field - Content has been reorganized to more closely match how instructors currently teach the course, with coverage of fluid mechanics and thermodynamics moved to the front of the book - Includes new design studies of several turbomachines, applying the theories developed in the book
Download or read book Principles of Turbomachinery written by Seppo A. Korpela and published by John Wiley & Sons. This book was released on 2019-07-11 with total page 592 pages. Available in PDF, EPUB and Kindle. Book excerpt: A newly updated and expanded edition that combines theory and applications of turbomachinery while covering several different types of turbomachinery In mechanical engineering, turbomachinery describes machines that transfer energy between a rotor and a fluid, including turbines, compressors, and pumps. Aiming for a unified treatment of the subject matter, with consistent notation and concepts, this new edition of a highly popular book provides all new information on turbomachinery, and includes 50% more exercises than the previous edition. It allows readers to easily move from a study of the most successful textbooks on thermodynamics and fluid dynamics to the subject of turbomachinery. The book also builds concepts systematically as progress is made through each chapter so that the user can progress at their own pace. Principles of Turbomachinery, 2nd Edition provides comprehensive coverage of everything readers need to know, including chapters on: thermodynamics, compressible flow, and principles of turbomachinery analysis. The book also looks at steam turbines, axial turbines, axial compressors, centrifugal compressors and pumps, radial inflow turbines, hydraulic turbines, hydraulic transmission of power, and wind turbines. New chapters on droplet laden flows of steam and oblique shocks help make this an incredibly current and well-rounded resource for students and practicing engineers. Includes 50% more exercises than the previous edition Uses MATLAB or GNU/OCTAVE for all the examples and exercises for which computer calculations are needed, including those for steam Allows for a smooth transition from the study of thermodynamics, fluid dynamics, and heat transfer to the subject of turbomachinery for students and professionals Organizes content so that more difficult material is left to the later sections of each chapter, allowing instructors to customize and tailor their courses for their students Principles of Turbomachinery is an excellent book for students and professionals in mechanical, chemical, and aeronautical engineering.
Download or read book Engineer design construct test and evaluate a pressurized fluidized bed pilot plant using high sulfur coal for production of electric power written by Curtiss-Wright Corporation. Power Systems Division and published by . This book was released on 1977 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Principles of Turbomachinery written by Seppo A. Korpela and published by Wiley. This book was released on 2011-12-13 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: The text is based on a course on turbomachinery which the author has taught since year 2000 as a technical elective. Topics include; Energy Transfer in Turbomachines, Gas and Steam Turbines, and Hydraulic Turbines. New material on wind turbines, and three-dimensional effects in axial turbomachines is included. The level is kept as such that students can smoothly move from a study of the most successful books in thermodynamics, fluid dynamics, and heat transfer to the subject of turbomachinery. The chapters are organized in such a way that the more difficult material is left to the later sectio.
Download or read book Selection and Use of Engineering Materials written by F A A Crane and published by Elsevier. This book was released on 1997-07-16 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selection and Use of Engineering Materials provides an understanding of the basic principles of materials selection as practised in engineering manufacture and design with an overview of established materials usage. Emphasis is placed on identifying service requirements and how materials relate to those requirements, rather than listing materials and describing applications. This edition has been revised throughout and now includes coverage of the use of new materials in engineering, materials for bearings and tribological usage, and the use of materials in civil engineering structures. It has also been expanded to include more case studies and worked examples in order to provide tangible and interactive contact with the content matter. The book also contains a detailed consideration of the weldability of steels, the welding of plastics and adhesion. programmes. An example of this development is the inclusion of a chapter detailing the use of materials in automobile structures; a field in which the traditional use of steel is being displaced as the application of reinforced polymers becomes more widespread. The book also reflects the growing use of computerized databases and materials selection programmes. - Core subject area for all engineering and materials degrees - Complementary to Materials Selection in Mechanical Design (Ashby) - Includes case studies and worked examples
