Download or read book Machining Recent Advances Applications and Challenges written by Luis Norberto L´opez de Lacalle and published by MDPI. This book was released on 2019-08-26 with total page 554 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Special Issue Machining—Recent Advances, Applications and Challenges is intended as a humble collection of some of the hottest topics in machining. The manufacturing industry is a varying and challenging environment where new advances emerge from one day to another. In recent years, new manufacturing procedures have retained increasing attention from the industrial and scientific community. However, machining still remains the key operation to achieve high productivity and precision for high-added value parts. Continuous research is performed, and new ideas are constantly considered. This Special Issue summarizes selected high-quality papers which were submitted, peer-reviewed, and recommended by experts. It covers some (but not only) of the following topics: High performance operations for difficult-to-cut alloys, wrought and cast materials, light alloys, ceramics, etc.; Cutting tools, grades, substrates and coatings. Wear damage; Advanced cooling in machining: Minimum quantity of lubricant, dry or cryogenics; Modelling, focused on the reduction of risks, the process outcome, and to maintain surface integrity; Vibration problems in machines: Active and passive/predictive methods, sources, diagnosis and avoidance; Influence of machining in new concepts of machine–tool, and machine static and dynamic behaviors; Machinability of new composites, brittle and emerging materials; Assisted machining processes by high-pressure, laser, US, and others; Introduction of new analytics and decision making into machining programming. We wish to thank the reviewers and staff from Materials for their comments, advice, suggestions and invaluable support during the development of this Special Issue.
Download or read book Metal Machining Recent Advances Applications and Challenges written by Francisco J G Silva and published by Mdpi AG. This book was released on 2021-11-26 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Machining remains one of the most important manufacturing processes in the metalworking industry. Studies on this process have investigated the machinability of different materials, the behaviour of tools, chip formation, surface integrity, forces involved, and its economic and environmental sustainability. New materials are constantly being developed, and machining research needs to closely follow these developments. This book examines recent research in the machining field, covering several aspects and presenting very interesting developments in this area of knowledge.
Download or read book Machining Recent Advances Applications and Challenges written by Luis Norberto López de Lacalle and published by . This book was released on 2019 with total page 1 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Special Issue Machining-Recent Advances, Applications and Challenges is intended as a humble collection of some of the hottest topics in machining. The manufacturing industry is a varying and challenging environment where new advances emerge from one day to another. In recent years, new manufacturing procedures have retained increasing attention from the industrial and scientific community. However, machining still remains the key operation to achieve high productivity and precision for high-added value parts. Continuous research is performed, and new ideas are constantly considered. This Special Issue summarizes selected high-quality papers which were submitted, peer-reviewed, and recommended by experts. It covers some (but not only) of the following topics: High performance operations for difficult-to-cut alloys, wrought and cast materials, light alloys, ceramics, etc.; Cutting tools, grades, substrates and coatings. Wear damage; Advanced cooling in machining: Minimum quantity of lubricant, dry or cryogenics; Modelling, focused on the reduction of risks, the process outcome, and to maintain surface integrity; Vibration problems in machines: Active and passive/predictive methods, sources, diagnosis and avoidance; Influence of machining in new concepts of machine-tool, and machine static and dynamic behaviors; Machinability of new composites, brittle and emerging materials; Assisted machining processes by high-pressure, laser, US, and others; Introduction of new analytics and decision making into machining programming. We wish to thank the reviewers and staff from Materials for their comments, advice, suggestions and invaluable support during the development of this Special Issue.
Download or read book Recent Advances in Logo Detection Using Machine Learning Paradigms written by Yen-Wei Chen and published by Springer Nature. This book was released on with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Recent Advances in Parallel Virtual Machine and Message Passing Interface written by Alexey Lastovetsky and published by Springer Science & Business Media. This book was released on 2008-08-28 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the refereed proceedings of the 15th European PVM/MPI Users' Group Meeting held in Dublin, Ireland, in September 2008. The 29 revised full papers presented together with abstracts of 7 invited contributions, 1 tutorial paper and 8 poster papers were carefully reviewed and selected from 55 submissions. The papers are organized in topical sections on applications, collective operations, library internals, message passing for multi-core and mutlithreaded architectures, MPI datatypes, MPI I/O, synchronisation issues in point-to-point and one-sided communications, tools, and verification of message passing programs. The volume is rounded off with 4 contributions to the special ParSim session on current trends in numerical simulation for parallel engineering environments.
Download or read book Machining written by J. Paulo Davim and published by Springer Science & Business Media. This book was released on 2008-07-11 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: Machining is one of the most important manufacturing processes. Parts manufactured by other processes often require further operations before the product is ready for application. “Machining: Fundamentals and Recent Advances” is divided into two parts. Part I explains the fundamentals of machining, with special emphasis on three important aspects: mechanics of machining, tools, and work-piece integrity. Part II is dedicated to recent advances in machining, including: machining of hard materials, machining of metal matrix composites, drilling polymeric matrix composites, ecological machining (minimal quantity of lubrication), high-speed machining (sculptured surfaces), grinding technology and new grinding wheels, micro- and nano-machining, non-traditional machining processes, and intelligent machining (computational methods and optimization). Advanced students, researchers and professionals interested or involved in modern manufacturing engineering will find the book a useful reference.
Download or read book Recent Advances in Ensembles for Feature Selection written by Verónica Bolón-Canedo and published by Springer. This book was released on 2018-04-30 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a comprehensive overview of ensemble learning in the field of feature selection (FS), which consists of combining the output of multiple methods to obtain better results than any single method. It reviews various techniques for combining partial results, measuring diversity and evaluating ensemble performance. With the advent of Big Data, feature selection (FS) has become more necessary than ever to achieve dimensionality reduction. With so many methods available, it is difficult to choose the most appropriate one for a given setting, thus making the ensemble paradigm an interesting alternative. The authors first focus on the foundations of ensemble learning and classical approaches, before diving into the specific aspects of ensembles for FS, such as combining partial results, measuring diversity and evaluating ensemble performance. Lastly, the book shows examples of successful applications of ensembles for FS and introduces the new challenges that researchers now face. As such, the book offers a valuable guide for all practitioners, researchers and graduate students in the areas of machine learning and data mining.
Download or read book Recent Advances and Emerging Challenges in STEM written by Yadir Torres and published by Springer Nature. This book was released on with total page 653 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Machining Processes of Metallic Materials written by Wit Grzesik and published by Elsevier. This book was released on 2016-11-15 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Machining Processes of Metallic Materials: Theory, Modelling and Applications, Second Edition, explores the metal cutting processes with regard to theory and industrial practice. Structured into three parts, the first section provides information on the fundamentals of machining, while the second and third parts include an overview of the effects of the theoretical and experimental considerations in high-level machining technology and a summary of production outputs related to part quality. In particular, topics discussed include: modern tool materials, mechanical, thermal and tribological aspects of machining, computer simulation of various process phenomena, chip control, monitoring of the cutting state, progressive and hybrid machining operations, as well as practical ways for improving machinability and generation and modeling of surface integrity. This new edition addresses the present state and future development of machining technologies, and includes expanded coverage on machining operations, such as turning, milling, drilling, and broaching, as well as a new chapter on sustainable machining processes. In addition, the book provides a comprehensive description of metal cutting theory and experimental and modeling techniques, along with basic machining processes and their effective use in a wide range of manufacturing applications. The research covered here has contributed to a more generalized vision of machining technology, including not only traditional manufacturing tasks, but also potential (emerging) new applications, such as micro and nanotechnology. - Includes new case studies illuminate experimental methods and outputs from different sectors of the manufacturing industry - Presents metal cutting processes that would be applicable for various technical, engineering, and scientific levels - Includes an updated knowledge of standards, cutting tool materials and tools, new machining technologies, relevant machinability records, optimization techniques, and surface integrity
Download or read book Machining written by J. Paulo Davim and published by Springer. This book was released on 2008-09-24 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Machining is one of the most important manufacturing processes. Parts manufactured by other processes often require further operations before the product is ready for application. “Machining: Fundamentals and Recent Advances” is divided into two parts. Part I explains the fundamentals of machining, with special emphasis on three important aspects: mechanics of machining, tools, and work-piece integrity. Part II is dedicated to recent advances in machining, including: machining of hard materials, machining of metal matrix composites, drilling polymeric matrix composites, ecological machining (minimal quantity of lubrication), high-speed machining (sculptured surfaces), grinding technology and new grinding wheels, micro- and nano-machining, non-traditional machining processes, and intelligent machining (computational methods and optimization). Advanced students, researchers and professionals interested or involved in modern manufacturing engineering will find the book a useful reference.
Download or read book Research Anthology on Machine Learning Techniques Methods and Applications written by Management Association, Information Resources and published by IGI Global. This book was released on 2022-05-13 with total page 1516 pages. Available in PDF, EPUB and Kindle. Book excerpt: Machine learning continues to have myriad applications across industries and fields. To ensure this technology is utilized appropriately and to its full potential, organizations must better understand exactly how and where it can be adapted. Further study on the applications of machine learning is required to discover its best practices, challenges, and strategies. The Research Anthology on Machine Learning Techniques, Methods, and Applications provides a thorough consideration of the innovative and emerging research within the area of machine learning. The book discusses how the technology has been used in the past as well as potential ways it can be used in the future to ensure industries continue to develop and grow. Covering a range of topics such as artificial intelligence, deep learning, cybersecurity, and robotics, this major reference work is ideal for computer scientists, managers, researchers, scholars, practitioners, academicians, instructors, and students.
Download or read book Metal Machining written by P.R.N. Childs and published by Butterworth-Heinemann. This book was released on 2013-10-22 with total page 420 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal machining is the most widespread metal-shaping process in the mechanical manufacturing industry. World-wide investment in metal machining tools increases year on year - and the wealth of nations can be judged by it. This text - the most up-to-date in the field - provides in-depth discussion of the theory and application of metal machining at an advanced level. It begins with an overview of the development of metal machining and its role in the current industrial environment and continues with a discussion of the theory and practice of machining. The underlying mechanics are analysed in detail and there are extensive chapters examining applications through a discussion of simulation and process control. "Metal Machining: Theory and Applications" is essential reading for senior undergraduates and postgraduates specialising in cutting technology. It is also an invaluable reference tool for professional engineers. Professors Childs, Maekawa, Obikawa and Yamane are four of the leading authorities on metal machining and have worked together for many years.Of interest to all mechanical, manufacturing and materials engineersTheoretical and practical problems addressed
Download or read book Machining of Hard Materials written by J. Paulo Davim and published by Springer Science & Business Media. This book was released on 2011-02-24 with total page 221 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hard machining is a relatively recent technology that can be defined as a machining operation, using tools with geometrically defined cutting edges, of a work piece that has hardness values typically in the 45-70HRc range. This operation always presents the challenge of selecting a cutting tool insert that facilitates high-precision machining of the component, but it presents several advantages when compared with the traditional methodology based in finish grinding operations after heat treatment of work pieces. Machining of Hard Materials aims to provide the reader with the fundamentals and recent advances in the field of hard machining of materials. All the chapters are written by international experts in this important field of research. They cover topics such as: • advanced cutting tools for the machining of hard materials; • the mechanics of cutting and chip formation; • surface integrity; • modelling and simulation; and • computational methods and optimization. Machining of Hard Materials can serve as a useful reference for academics, manufacturing and materials researchers, manufacturing and mechanical engineers, and professionals in machining and related industries. It can also be used as a text for advanced undergraduate or postgraduate students studying mechanical engineering, manufacturing, or materials.
Download or read book Machine Learning Applications in Non Conventional Machining Processes written by Bose, Goutam Kumar and published by IGI Global. This book was released on 2021-02-05 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Traditional machining has many limitations in today’s technology-driven world, which has caused industrial professionals to begin implementing various optimization techniques within their machining processes. The application of methods including machine learning and genetic algorithms has recently transformed the manufacturing industry and created countless opportunities in non-traditional machining methods. Significant research in this area, however, is still considerably lacking. Machine Learning Applications in Non-Conventional Machining Processes is a collection of innovative research on the advancement of intelligent technology in industrial environments and its applications within the manufacturing field. While highlighting topics including evolutionary algorithms, micro-machining, and artificial neural networks, this book is ideally designed for researchers, academicians, engineers, managers, developers, practitioners, industrialists, and students seeking current research on intelligence-based machining processes in today’s technology-driven market.
Download or read book Real World Challenges in Quantum Electronics and Machine Computing written by Ananth, Christo and published by IGI Global. This book was released on 2024-08-05 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quantum computers are unparalleled in terms of computational power, and they have a multitude of promising applications. However, these computers are prone to noise and instability caused by environmental interactions, making the use of these advanced machines rather impractical in most scenarios. Despite these challenges, Real-World Challenges in Quantum Electronics and Machine Computing provides innovative solutions to navigate the complexities of quantum computation, thus offering hope during this time of turbulence. By delving into the intricacies of quantum electronics and machine computing, this book equips readers with the tools to overcome the hurdles obstructing the path to practical quantum computing. It serves as a roadmap for students, practitioners, and professionals, guiding them through the intricacies of error correction techniques and hardware development. With its comprehensive coverage of cutting-edge topics and innovative solutions, the book empowers readers to tackle the most pressing challenges facing the quantum computing landscape. As researchers and engineers strive to unlock the full potential of quantum computation, this book stands as an indispensable resource, guiding them toward a future where quantum computing transcends the realm of theory and becomes a tangible reality.
Download or read book Machine Learning for Sustainable Development written by Kamal Kant Hiran and published by Walter de Gruyter GmbH & Co KG. This book was released on 2021-07-19 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book will focus on the applications of machine learning for sustainable development. Machine learning (ML) is an emerging technique whose diffusion and adoption in various sectors (such as energy, agriculture, internet of things, infrastructure) will be of enormous benefit. The state of the art of machine learning models is most useful for forecasting and prediction of various sectors for sustainable development.
Download or read book Recent Advances in Applied Science and Engineering written by Dr. Ankita Saini and published by Writers Corner Publication. This book was released on 2024-02-14 with total page 349 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Recent Advances in Applied Science and Engineering" represents a thorough and state-of-the-art exploration of the most recent developments across various disciplines within the fields of applied science and engineering. Each chapter provides in-depth analyses of emerging technologies, methodologies, and discoveries, emphasizing the practical applications of these advancements to address real-world challenges. Furthermore, the book not only showcases recent achievements but also engages in discussions about potential future directions and challenges in applied science and engineering. This forward-looking approach offers readers a roadmap for upcoming research areas and opportunities for innovation. Serving as an indispensable resource, this book provides a comprehensive overview of the latest developments in these rapidly evolving fields. Whether a researcher or student, readers will find this book to be a valuable reference for staying informed about the most recent advancements shaping the future of applied science and engineering.
