Download or read book Machining Data for Numerical Control Peripheral End Milling written by Michael Field and published by . This book was released on 1966 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. Specifically this report, the fourth of a series, pertains to peripheral end milling.
Download or read book Machining Data for Numerical Control End Mill Slotting written by Michael Field and published by . This book was released on 1966 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. Specifically, this report, the sixth of a series, pertains to tapping. The remaining report in this series will be issued separately as: Reaming (Report No. 66-1.7). Upon completion, all reports will be collected in a single volume (Report No. 66-1). The previous reports are Turning, No. 66-1.1; Face Milling, No. 66-1.2; Drilling, No. 66-1.3; Peripheral End Milling, No. 66-1.4; and End Mill Slotting, No. 66-1.5. (Author).
Download or read book Machining Data for Numerical Control End Mill Slotting written by Michael Field and published by . This book was released on 1966 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. Specifically, this report, the sixth of a series, pertains to tapping. The remaining report in this series will be issued separately as: Reaming (Report No. 66-1.7). Upon completion, all reports will be collected in a single volume (Report No. 66-1). The previous reports are Turning, No. 66-1.1; Face Milling, No. 66-1.2; Drilling, No. 66-1.3; Peripheral End Milling, No. 66-1.4; and End Mill Slotting, No. 66-1.5. (Author).
Download or read book Machining Data for Numerical Control Face Milling written by Michael Field and published by . This book was released on 1966 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, width, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situatuion involving the materials for which machining data are presented. Specifically this report, the second of a series, pertains to face milling. (Author).
Download or read book Machining Data for Numerical Control Reaming written by Michael Field and published by . This book was released on 1966 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. Specifically this report, the last of a series, pertains to reaming. The previous reports in this series were issued separately as: Turning, Face Milling, Drilling, Peripheral End Milling, End Mill Slotting, and Tapping (Report Nos. AFMDC 66-1.1 through 66-1.6). All reports will be collected in a single volume (Report No. AFMDC 66-1). (Author).
Download or read book Machining Data for Numerical Control Drilling written by Michael Field and published by . This book was released on 1966 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool material, tool geometry, cutting fluid, depth, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. Specifically this report, the third of a series, pertains to drilling.
Download or read book Machining Data for Numerical Control written by Air Force Machinability Data Center and published by . This book was released on 1966 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from six USAF Machinability Reports. Data are tabulated and arranged in formats including machining variables such as tool materials, tool geometry, cutting fluid, depth, width, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. This report covers: Turning, Face Milling, Drilling, Peripheral End Milling, End Mill Slotting, Tapping, and Reaming. (Author).
Download or read book 1968 Supplement to Machining Data for Numerical Control written by Air Force Machinability Data Center and published by . This book was released on 1968 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents an extensive set of machining data selected from the latest USAF Machinability Report. Data are tabulated and arranged in formats including machining variables such as tool materials, tool geometry, cutting fluid, depth, width, feed, and tool life end point. For each of the data lines, the relationship between tool life and cutting speed is expressed in at least three sets of data, thereby making it possible to optimize for maximum production or minimum cost. While these data are expected to be of considerable assistance in providing data for numerical control applications, they are also of great value in any type of machining situation involving the materials for which machining data are presented. This report covers; Turning, Face Milling, Drilling, Peripheral End Milling, End Mill Slotting, Tapping, and Reaming. Material groups covered are Ultra-High Strength Steels, Stainless Steels, Titanium Alloys, and Nickel-Base High Temperature Alloys. (Author).
Download or read book Machining Data for Beryllium Metal written by Air Force Machinability Data Center and published by . This book was released on 1966 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report contains evaluated machining information for beryllium which has been extracted from many sources. Machining data are tabulated and presented in chart form for the following processes: turning, milling, drilling, band sawing, grinding, boring, trepanning, reaming, routing, tapping, electrical discharge machining, electrochemical machining, and chemical machining. Also included is a general comment section dealing with the problems associated with beryllium machining, such as twinning, microcracking, toxicity, chipout and spalling, and cutting fluids. (Author).
Download or read book Government wide Index to Federal Research Development Reports written by and published by . This book was released on 1967 with total page 1352 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Technical Abstract Bulletin written by and published by . This book was released on with total page 776 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Numerical Control of Machine Tools written by Hampshire Technical Research Industrial Commercial Service and published by . This book was released on 1970 with total page 158 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book N C Machinability Data Systems written by Noel R. Parsons and published by . This book was released on 1971 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book U S Government Research Development Reports written by and published by . This book was released on 1967 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Selected Advances in Tools Dies Jigs and Fixtures Technology written by United States. Small Business Administration. Technology Utilization Division and published by . This book was released on 1968 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machining Data Handbook written by Machinability Data Center and published by . This book was released on 1980 with total page 1220 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machining of New Materials written by Norman Zlatin and published by . This book was released on 1973 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt:
