Download or read book Machine Tools Production Systems 3 written by Christian Brecher and published by Springer Nature. This book was released on 2021-12-13 with total page 712 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first part of this third volume focuses on the design of mechatronic components, in particular the feed drives of machine tools used to generate highly dynamic drive movements. Engineering guides for the selection and design of important machine components, the control technology of feed drives, and the measuring systems required for position capture are presented. Another focus is on process and diagnostic equipment for manufacturing machines and systems. The second part describes control concepts including programming methods for various applications of modern production systems. Programmable logic controllers (PLC), numerical controllers (NC) and robot controllers (RC) are part of these presentations. In the context of automated manufacturing systems, the various levels of the automation pyramid and the importance of control systems are also outlined. Finally, the volume deals with the engineering of machines and plants. The German Machine Tools and Production Systems Compendium has been completely revised. The previous five-volume series has been condensed into three volumes in the new ninth edition with colored technical illustrations throughout. This first English edition is a translation of the German ninth edition.
Download or read book Machine Tools Production Systems 1 written by Christian Brecher and published by Springer Nature. This book was released on with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machine Tools Production Systems 2 written by Christian Brecher and published by Springer Nature. This book was released on 2021-11-08 with total page 850 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first part of this volume provides the user with assistance in the selection and design of important machine and frame components. It also provides help with machine design, calculation and optimization of these components in terms of their static, dynamic and thermoelastic behavior. This includes machine installation, hydraulic systems, transmissions, as well as industrial design and guidelines for machine design. The second part of this volume deals with the metrological investigation and assessment of the entire machine tool or its components with respect to the properties discussed in the first part of this volume. Following an overview of the basic principles of measurement and measuring devices, the procedure for measuring them is described. Acceptance of the machine using test workpieces and the interaction between the machine and the machining process are discussed in detail. The German Machine Tools and Manufacturing Systems Compendium has been completely revised. The previous five-volume series has been condensed into three volumes in the new ninth edition with color technical illustrations throughout. This first English edition is a translation of the German ninth edition.
Download or read book Fundamentals of Machining and Machine Tools written by and published by I. K. International Pvt Ltd. This book was released on 2013-12-30 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals of Machining and Machine Tools deals with analytical modeling techniques of machining processes, modern cutting tool materials and their effects on the economics of machining. The book thoroughly illustrates the causes of various phenomena and their effects on machining practice. It includes description of machining processes outlining the merits and de-merits of various modeling approaches. Spread in 22 chapters, the book is broadly divided in four sections: 1. Machining Processes 2. Cutting Tools 3. Machine Tools 4. Automation Data on cutting parameters for machining operations and main characteristics of machine tools have been separately provided in Annexures. In addition to exhaustive theory, a number of numerical examples have been solved and arranged in various chapters. Question bank has been given at the end of every chapter. The book is a must for anyone involved in metal cutting, machining, machine tool technology, machining applications, and manufacturing processes
Download or read book Information Control Problems in Manufacturing Technology 1989 written by E.A. Puente and published by Elsevier. This book was released on 2014-06-28 with total page 711 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Symposium presented and discussed the latest research on new theories and advanced applications of automatic systems, which are developed for manufacturing technology or are applicable to advanced manufacturing systems. The topics included computer integrated manufacturing, simulation and the increasingly important areas of artificial intelligence and expert systems, and applied them to the broad spectrum of problems that the modern manufacturing engineer is likely to encounter in the design and application of increasingly complex automatic systems.
Download or read book Machine Tool Design written by N. Acherkan and published by . This book was released on 2000 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: This fundamental four-volume work was translated from the considerably revised second edition. It should be of great value to engineers engaged in the design, manufacture and maintenance of machine tool equipment. It can also be used to advantage by the students of engineering institutes majoring in Process Engineering, Metal-Cutting Machine Tools or Cutting Tool Design. The first volume deals with the basic machine tools and special machine tools used in cutting tool production. The classification, type and size range, and designation of machine tools, employed in Soviet practice, are given in detail, together with the types of motion found in machine tools. Metal-cutting lathes, turret lathes, vertical boring machines, automatic and semiautomatic lathes, milling machines and many other types of machine tools are described. Special attention has been given to machine tools designed for the production of cutting tools. These include general and single-purpose semiautomatic precision thread-grinding machines, automatic and semiautomatic tracer-controlled lathes with hydraulic controls, jig boring machines and specialized machine tools, as well as automatic transfer machines for cutting tool production. Volume two contains Parts Three and Four. Part Three deals with the kinematics of machine tools. This branch of machine tool design has been strictly systematized by the author and is set forth with exceptional clarity. The kinematic structures of a great many different types of machine tools, including the most complex gear-cutting machines, are analyzed by methods developed in the text which take into consideration the interrelation between the workpiece to be produced in the given machine tool. Part Four takes up hydraulic drives of machine tools. It contains all the theoretical and practical data required in the application of fluid power and control systems to machine tools. Volume Three contains Part Five and this deals with machine tool design proper. It is a comprehensive scientific treatment of the subject and is a revised and complemented version of a previous Russian edition which has become a reliable reference book for all Soviet machine tool engineers and has been translated into French. Such questions as performance criteria, basic design data, principal specifications and the development of the kinematic scheme of a new machine tool are dealt with in great detail. Design recommendations are given as well as the necessary calculation data for the basic elements of machine tools - speed and feed gearboxes, steeples drives, rapid traverse mechanisms, spindles and spindle bearings, mechanisms for rectilinear motion, small displacement and periodic motion, reversing devices, beds columns, tables and other housing-type components, slideways and antifriction ways. The fourth and final volume covers Automatic Machine Tools and Transfer Machines, and Machine Tool Testing and Research, Parts Six and Seven of the complete work. Part Six deals with the fundamental principles of machine tool automation, the various systems of numerical programmed control that have found extensive application in modern machine tool design in the USSR and other countries. Much space has been given to automatic transfer machines, including in-line, rotary, and other types, their layout, features, design procedures, structure, and output. Current methods of testing and investigating the geometrical, kinematic, dynamic, and operational characteristics of machine tools are considered in Part Seven. Methods of testing the quality characteristics, of determining the corresponding criteria (indices), and of using contemporary apparatus for this purpose are dealt with.
Download or read book Transition Towards Energy Efficient Machine Tools written by André Zein and published by Springer Science & Business Media. This book was released on 2012-12-16 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: Energy efficiency represents a cost-effective and immediate strategy of a sustainable development. Due to substantial environmental and economic implications, a strong emphasis is put on the electrical energy requirements of machine tools for metalworking processes. The improvement of energy efficiency is however confronted with diverse barriers, which sustain an energy efficiency gap of unexploited potential. The deficiencies lie in the lack of information about the actual energy requirements of machine tools, a minimum energy reference to quantify improvement potential and the possible actions to improve the energy demand. Therefore, a comprehensive concept for energy performance management of machine tools is developed which guides the transition towards energy efficient machine tools. It is structured in four innovative concept modules, which are embedded into step-by-step workflow models. The capability of the performance management concept is demonstrated in an automotive manufacturing environment. The target audience primarily comprises researchers and practitioners challenged to enhance energy efficiency in manufacturing. The book may also be beneficial for graduate students who want to specialize in this field.
Download or read book Automation Production Systems and Computer integrated Manufacturing written by Mikell P. Groover and published by Prentice Hall. This book was released on 2008 with total page 832 pages. Available in PDF, EPUB and Kindle. Book excerpt: This exploration of the technical and engineering aspects of automated production systems provides a comprehensive and balanced coverage of the subject. It covers cutting-edge technologies of production automation and material handling, and how these technologies are used to construct modern manufacturing systems.
Download or read book Fundamentals of Metal Machining and Machine Tools Third Edition written by Geoffrey Boothroyd and published by CRC Press. This book was released on 1988-11-15 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt: New edition (previous, 1975) of a textbook for a college-level course in the principles of machine tools and metal machining. Math demands are limited to introductory calculus and that encountered in basic statics and dynamics. Topics include: operations, mechanics of cutting, temperature, tool life
Download or read book Twin Control written by Mikel Armendia and published by Springer. This book was released on 2019-01-05 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book summarizes the results of the European research project “Twin-model based virtual manufacturing for machine tool-process simulation and control” (Twin-Control). The first part reviews the applications of ICTs in machine tools and manufacturing, from a scientific and industrial point of view, and introduces the Twin-Control approach, while Part 2 discusses the development of a digital twin of machine tools. The third part addresses the monitoring and data management infrastructure of machines and manufacturing processes and numerous applications of energy monitoring. Part 4 then highlights various features developed in the project by combining the developments covered in Parts 3 and 4 to control the manufacturing processes applying the so-called CPSs. Lastly, Part 5 presents a complete validation of Twin-Control features in two key industrial sectors: aerospace and automotive. The book offers a representative overview of the latest trends in the manufacturing industry, with a focus on machine tools.
Download or read book Intelligent Production Machines and Systems 2nd I PROMS Virtual International Conference 3 14 July 2006 written by Duc T. Pham and published by Elsevier. This book was released on 2007-01-22 with total page 698 pages. Available in PDF, EPUB and Kindle. Book excerpt: I*PROMS 2005 is an online web-based conference. It provides a platform for presenting, discussing, and disseminating research results contributed by scientists and industrial practitioners active in the area of intelligent systems and soft computing techniques (such as fuzzy logic, neural networks, evolutionary algorithms, and knowledge-based systems) and their application in different areas of manufacturing. Comprised of 100 peer-reviewed articles, this important resource provides tools to help enterprises achieve goals critical to the future of manufacturing. I*PROMS is an European Union-funded network that involves 30 partner organizations and more than 130 researchers from universities, research organizations, and corporations. * State-of-the-art research results * Leading European researchers and industrial practitioners * Comprehensive collection of indexed and peer-reviewed articles in book format supported by a user-friendly full-text CD-ROM with search functionality
Download or read book Operation and Diagnostics of Machines and Production Systems Operational States III written by Tibor Krenicky and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Collection of selected, peer reviewed papers from the special topic volume with invited peer reviewed papers only.The 66 papers are grouped as follows:Chapter 1: Operation of the Systems for Plastics Processing;Chapter 2: Operation of the Systems for Metal Machining;Chapter 3: Operation of the Systems for Water Jet Technology;Chapter 4: Tools and Equipments in Production Systems for Material Machining;Chapter 5: Diagnostics and Measurement Operational States of Machines;Chapter 6: Engineering of Production Systems
Download or read book Flexible Manufacturing Systems written by Fred Choobineh and published by . This book was released on 1986 with total page 446 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Manufacturing Systems written by David J. Williams and published by . This book was released on 1988 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machine Tool Reliability written by Bhupesh K. Lad and published by John Wiley & Sons. This book was released on 2016-04-04 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the domain of reliability engineering in the context of machine tools. Failures of machine tools not only jeopardize users' ability to meet their due date commitments but also lead to poor quality of products, slower production, down time losses etc. Poor reliability and improper maintenance of a machine tool greatly increases the life cycle cost to the user. Thus, the application area of the present book, i.e. machine tools, will be equally appealing to machine tool designers, production engineers and maintenance managers. The book will serve as a consolidated volume on various dimensions of machine tool reliability and its implications from manufacturers and users point of view. From the manufacturers' point of view, it discusses various approaches for reliability and maintenance based design of machine tools. In specific, it discusses simultaneous selection of optimal reliability configuration and maintenance schedules, maintenance optimization under various maintenance scenarios and cost based FMEA. From the users' point of view, it explores the role of machine tool reliability in shop floor level decision- making. In specific, it shows how to model the interactions of machine tool reliability with production scheduling, maintenance scheduling and process quality control.
Download or read book Which Degree written by and published by . This book was released on 1977 with total page 1256 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the CIRP Seminars on Manufacturing Systems fertigungssysteme syst mes de Fabrication written by and published by . This book was released on 1988 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt:
