Download or read book Machine Tools Production Systems 1 written by Christian Brecher and published by Springer Nature. This book was released on with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machine Tools Production Systems 2 written by Christian Brecher and published by Springer Nature. This book was released on 2021-11-08 with total page 850 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first part of this volume provides the user with assistance in the selection and design of important machine and frame components. It also provides help with machine design, calculation and optimization of these components in terms of their static, dynamic and thermoelastic behavior. This includes machine installation, hydraulic systems, transmissions, as well as industrial design and guidelines for machine design. The second part of this volume deals with the metrological investigation and assessment of the entire machine tool or its components with respect to the properties discussed in the first part of this volume. Following an overview of the basic principles of measurement and measuring devices, the procedure for measuring them is described. Acceptance of the machine using test workpieces and the interaction between the machine and the machining process are discussed in detail. The German Machine Tools and Manufacturing Systems Compendium has been completely revised. The previous five-volume series has been condensed into three volumes in the new ninth edition with color technical illustrations throughout. This first English edition is a translation of the German ninth edition.
Download or read book Machine Tools Production Systems 3 written by Christian Brecher and published by Springer Nature. This book was released on 2021-12-13 with total page 712 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first part of this third volume focuses on the design of mechatronic components, in particular the feed drives of machine tools used to generate highly dynamic drive movements. Engineering guides for the selection and design of important machine components, the control technology of feed drives, and the measuring systems required for position capture are presented. Another focus is on process and diagnostic equipment for manufacturing machines and systems. The second part describes control concepts including programming methods for various applications of modern production systems. Programmable logic controllers (PLC), numerical controllers (NC) and robot controllers (RC) are part of these presentations. In the context of automated manufacturing systems, the various levels of the automation pyramid and the importance of control systems are also outlined. Finally, the volume deals with the engineering of machines and plants. The German Machine Tools and Production Systems Compendium has been completely revised. The previous five-volume series has been condensed into three volumes in the new ninth edition with colored technical illustrations throughout. This first English edition is a translation of the German ninth edition.
Download or read book Information Control Problems in Manufacturing Technology 1989 written by E.A. Puente and published by Elsevier. This book was released on 2014-06-28 with total page 711 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Symposium presented and discussed the latest research on new theories and advanced applications of automatic systems, which are developed for manufacturing technology or are applicable to advanced manufacturing systems. The topics included computer integrated manufacturing, simulation and the increasingly important areas of artificial intelligence and expert systems, and applied them to the broad spectrum of problems that the modern manufacturing engineer is likely to encounter in the design and application of increasingly complex automatic systems.
Download or read book Machine Tools written by Ľubomír Šooš and published by BoD – Books on Demand. This book was released on 2020-10 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: Successful producers of machine tools today must offer customers highly efficient and accurate machines. This can only be achieved with the help of modern software in research, construction, production and quality control. Trends in development are oriented towards modular construction machines. The application of modern tools and the progressive construction of headstock has increased cutting speeds, thus significantly increasing the machine's productivity. The first section of the book is focused on trends in the development of machines. A second very significant machine parameter is accuracy. The rigidity of the machine is a necessary condition for achieving its required accuracy. The second part of the book is dedicated to the effect of the individual constructional nodes on stability, the optimization of system rigidity, and the measuring of the accuracy of the machining tools. The aim of the third and final section of the book is to point out the widest possibilities for the application of machine tools in industry. An example is presented of the application of machining tools in the orthoses manufacture.
Download or read book Functional Reverse Engineering of Strategic and Non Strategic Machine Tools written by Wasim Ahmed Khan and published by CRC Press. This book was released on 2021-06-20 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes capacity building in strategic and non-strategic machine tool technology. It includes machine building in sectors such as machine tools, automobiles, home appliances, energy, and biomedical engineering, along with case studies. The book offers guidelines for capacity building in academia, covering how to promote enterprises of functional reverse engineering enterprises. It also discusses machine tool development, engineering design, prototyping of strategic, and non-strategies machine tools, as well as presenting communication strategies and IoT, along with case studies. Professionals from the CNC (Computer Numeric Control) machine tools industry, industrial and manufacturing engineers, and students and faculty in engineering disciplines will find interest in this book.
Download or read book Machinery and Production Engineering written by and published by . This book was released on 1923 with total page 938 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Twin Control written by Mikel Armendia and published by Springer. This book was released on 2019-01-05 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book summarizes the results of the European research project “Twin-model based virtual manufacturing for machine tool-process simulation and control” (Twin-Control). The first part reviews the applications of ICTs in machine tools and manufacturing, from a scientific and industrial point of view, and introduces the Twin-Control approach, while Part 2 discusses the development of a digital twin of machine tools. The third part addresses the monitoring and data management infrastructure of machines and manufacturing processes and numerous applications of energy monitoring. Part 4 then highlights various features developed in the project by combining the developments covered in Parts 3 and 4 to control the manufacturing processes applying the so-called CPSs. Lastly, Part 5 presents a complete validation of Twin-Control features in two key industrial sectors: aerospace and automotive. The book offers a representative overview of the latest trends in the manufacturing industry, with a focus on machine tools.
Download or read book Fundamentals of Machining and Machine Tools written by and published by I. K. International Pvt Ltd. This book was released on 2013-12-30 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals of Machining and Machine Tools deals with analytical modeling techniques of machining processes, modern cutting tool materials and their effects on the economics of machining. The book thoroughly illustrates the causes of various phenomena and their effects on machining practice. It includes description of machining processes outlining the merits and de-merits of various modeling approaches. Spread in 22 chapters, the book is broadly divided in four sections: 1. Machining Processes 2. Cutting Tools 3. Machine Tools 4. Automation Data on cutting parameters for machining operations and main characteristics of machine tools have been separately provided in Annexures. In addition to exhaustive theory, a number of numerical examples have been solved and arranged in various chapters. Question bank has been given at the end of every chapter. The book is a must for anyone involved in metal cutting, machining, machine tool technology, machining applications, and manufacturing processes
Download or read book Technology of Machine Tools written by KRAR and published by . This book was released on 2019-02-21 with total page 944 pages. Available in PDF, EPUB and Kindle. Book excerpt: Technology of Machine Tools, 8e provides state-of-the-art training for using machine tools in manufacturing technology, including up-to-date coverage of computer numerical control (CNC). It includes an overview of machine trades and career opportunities followed by theory and application. The text is structured to provide coverage of tools and measurement, machining tools and procedures, drilling and milling machines, computer-aided machining, and metallurgy. There is expanded coverage of computer-related technologies, including computer numerical control (CNC) and computer-aided design and manufacturing (CAD/CAM).
Download or read book Enabling Manufacturing Competitiveness and Economic Sustainability written by Michael F. Zaeh and published by Springer Science & Business Media. This book was released on 2013-09-12 with total page 472 pages. Available in PDF, EPUB and Kindle. Book excerpt: The changing manufacturing environment requires more responsive and adaptable manufacturing systems. The theme of the 5th International Conference on Changeable, Agile, Reconfigurable and Virtual production (CARV2013) is "Enabling Manufacturing Competitiveness and Economic Sustainability. Leading edge research and best implementation practices and experiences, which address these important issues and challenges, are presented. The proceedings include advances in manufacturing systems design, planning, evaluation, control and evolving paradigms such as mass customization, personalization, changeability, re-configurability and flexibility. New and important concepts such as the dynamic product families and platforms, co-evolution of products and systems, and methods for enhancing manufacturing systems' economic sustainability and prolonging their life to produce more than one product generation are treated. Enablers of change in manufacturing systems, production volume and capability, scalability and managing the volatility of markets, competition among global enterprises and the increasing complexity of products, manufacturing systems and management strategies are discussed. Industry challenges and future directions for research and development needed to help both practitioners and academicians are presented. About the Editor Prof. Dr.-Ing. Michael F. Zaeh, born in 1963, has been and is Professor for and Manufacturing Technology since 2002 and, together with Prof. Dr.-Ing. Gunther Reinhart, Head of the Institute for Machine Tools and Industrial Management (iwb) at the Technische Universitaet Muenchen (TUM). After studying general mechanical engineering, he was doctoral candidate under Prof. Dr.-Ing. Joachim Milberg at TUM from 1990 until 1993 and received his doctorate in 1993. From 1994 to 1995, he was department leader under Prof. Dr.-Ing. Gunther Reinhart. From 1996 to 2002, he worked for a machine tool manufacturer in several positions, most recently as a member of the extended management. Prof. Dr.-Ing. Michael F. Zaeh is an associated member of the CIRP and member of acatech, WGP and WLP. His current researches include among others Joining and Cutting Technologies like Laser Cutting and Welding as well as Friction Stir Welding, Structural Behaviour and Energy Efficiency of Machine Tools and Manufacturing Processes like Additive Manufacturing.
Download or read book AMST 05 Advanced Manufacturing Systems and Technology written by Elso Kuljanic and published by Springer Science & Business Media. This book was released on 2005-07-01 with total page 818 pages. Available in PDF, EPUB and Kindle. Book excerpt: Manufacturing a product is not difficult, the difficulty consists in manufacturing a product of high quality, at a low cost and rapidly. Drastic technological advances are changing global markets very rapidly. In such conditions the ability to compete successfully must be based on innovative ideas and new products which has to be of high quality yet low in price. One way to achieve these objecti ves would be through massive investments in research of computer based technology and by applying the approaches presented in this book. The First International Conference on Advanced Manufacturing Systems and Technology AMST87 was held in Opatija (Croatia) in October 1987. The Second International Conference on Advanced Manufacturing Systems and Technology AMSV90 was held in Trento (Italy) in lune 1990. The Third, Fourth, Fifth and Sixth Conferences on Advanced Manufacturing Systems and Technology were all held in Udine (Italy) as follows: AMST93 in April 1993, AMST96 in September 1996, AMST99 in June 1999 and AMST02 in June 2002.
Download or read book Introduction to Manufacturing Systems written by Professor Samuel C. Obi and published by Author House. This book was released on 2013-01-03 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to Manufacturing Systems is written for all college- and university-level manufacturing, industrial technology, engineering technology, industrial design, engineering, business management and other related disciplines where there is an interest in learning about manufacturing systems as a complete system. Even lay people will find this book useful in their quest to learn more about the field. Its simple and easy-to-understand language makes it particularly useful to all readers. The field of manufacturing is a world of its own which bears on almost all other disciplines. This book is not necessarily a “how to” material that teaches one how to manufacture a product, but rather an aid to help learners gain a more complete understanding of “what is in it” and “what happens in the field”. Thus, this book will provide more comprehensive information about manufacturing. It is intended to introduce every interested person to what manufacturing is, its diverse components, and the various activities and tasks that are undertaken in its many and diverse departments. It should serve as an introductory material to beginning college manufacturing and related majors. Over the years, I have learned that most of these beginners are ill equipped with key aspects of manufacturing when they arrive. This group also includes all technical- and business-minded individuals who enroll or train in trade, business, engineering, vocational and technical programs and institutions. This book is divided into 12 very distinctive chapters that are closely arranged to follow manufacturing activities as sequentially as possible, to help readers follow a rather continuous thread of activities generally undertaken in the industry. Its chapters cover various topics including different types, techniques or methods, and philosophies of manufacturing; manufacturing plants and facilities; manufacturing machines; tools and production tooling; manufacturing processes; manufacturing materials and material handling systems; measurement instruments; manufacturing personnel; manufactured products; and planning, implementing, controlling and improving manufacturing systems.
Download or read book Machine Tool Reliability written by Bhupesh K. Lad and published by John Wiley & Sons. This book was released on 2016-04-04 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the domain of reliability engineering in the context of machine tools. Failures of machine tools not only jeopardize users' ability to meet their due date commitments but also lead to poor quality of products, slower production, down time losses etc. Poor reliability and improper maintenance of a machine tool greatly increases the life cycle cost to the user. Thus, the application area of the present book, i.e. machine tools, will be equally appealing to machine tool designers, production engineers and maintenance managers. The book will serve as a consolidated volume on various dimensions of machine tool reliability and its implications from manufacturers and users point of view. From the manufacturers' point of view, it discusses various approaches for reliability and maintenance based design of machine tools. In specific, it discusses simultaneous selection of optimal reliability configuration and maintenance schedules, maintenance optimization under various maintenance scenarios and cost based FMEA. From the users' point of view, it explores the role of machine tool reliability in shop floor level decision- making. In specific, it shows how to model the interactions of machine tool reliability with production scheduling, maintenance scheduling and process quality control.
Download or read book Energy Efficient Manufacturing written by John W. Sutherland and published by John Wiley & Sons. This book was released on 2018-08-14 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the last several years, manufacturers have expressed increasing interest in reducing their energy consumption and have begun to search for opportunities to reduce their energy usage. In this book, the authors explore a variety of opportunities to reduce the energy footprint of manufacturing. These opportunities cover the entire spatial scale of the manufacturing enterprise: from unit process-oriented approaches to enterprise-level strategies. Each chapter examines some aspect of this spatial scale, and discusses and describes the opportunities that exist at that level. Case studies demonstrate how the opportunity may be acted on with practical guidance on how to respond to these opportunities.
Download or read book Machine Tool Vibrations and Cutting Dynamics written by Brandon C. Gegg and published by Springer Science & Business Media. This book was released on 2011-05-30 with total page 187 pages. Available in PDF, EPUB and Kindle. Book excerpt: “Machine Tool Vibrations and Cutting Dynamics” covers the fundamentals of cutting dynamics from the perspective of discontinuous systems theory. It shows the reader how to use coupling, interaction, and different cutting states to mitigate machining instability and enable better machine tool design. Among the topics discussed are; underlying dynamics of cutting and interruptions in cutting motions; the operation of the machine-tool systems over a broad range of operating conditions with minimal vibration and the need for high precision, high yield micro- and nano-machining.
Download or read book Manufacturing Systems Engineering written by Katsundo Hitomi and published by Routledge. This book was released on 2017-10-19 with total page 560 pages. Available in PDF, EPUB and Kindle. Book excerpt: This second edition of the classic textbook has been written to provide a completely up-to-date text for students of mechanical, industrial, manufacturing and production engineering, and is an indispensable reference for professional industrial engineers and managers. In his outstanding book, Professor Katsundo Hitomi integrates three key themes into the text: * manufacturing technology * production management * industrial economics Manufacturing technology is concerned with the flow of materials from the acquisition of raw materials, through conversion in the workshop to the shipping of finished goods to the customer. Production management deals with the flow of information, by which the flow of materials is managed efficiently, through planning and control techniques. Industrial economics focuses on the flow of production costs, aiming to minimise these to facilitate competitive pricing. Professor Hitomi argues that the fundamental purpose of manufacturing is to create tangible goods, and it has a tradition dating back to the prehistoric toolmakers. The fundamental importance of manufacturing is that it facilitates basic existence, it creates wealth, and it contributes to human happiness - manufacturing matters. Nowadays we regard manufacturing as operating in these other contexts, beyond the technological. It is in this unique synthesis that Professor Hitomi's study constitutes a new discipline: manufacturing systems engineering - a system that will promote manufacturing excellence. Key Features: * The classic textbook in manufacturing engineering * Fully revised edition providing a modern introduction to manufacturing technology, production managment and industrial economics * Includes review questions and problems for the student reader
