Download or read book Learning SOLIDWORKS 2022 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2022-03 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Learning SOLIDWORKS 2022 written by Randy Shih and published by SDC Publications. This book was released on 2022-03 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using SOLIDWORKS 2022 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the SOLIDWORKS interface and its basic tools right away. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of SOLIDWORKS's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using SOLIDWORKS. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanisms, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the second to last chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. Finally, in the last chapter, the author introduces you to 3D printing. You will learn the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. Being able to turn your designs into physical objects will open up a whole new world of possibilities to you. There are many books that show you how to perform individual tasks with SOLIDWORKS, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Learning SOLIDWORKS 2021 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2021-03 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Learning SOLIDWORKS 2020 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2020-02 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Learning SOLIDWORKS 2023 with Robot Kit written by Randy Shih and published by . This book was released on 2023-03 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book SOLIDWORKS 2022 Tutorial written by David Planchard and published by SDC Publications. This book was released on with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Uses step-by-step, project based tutorials designed for beginning or intermediate users • Will prepare you for the Certified SOLIDWORKS Associate Exam • Includes a chapter introducing you to 3D printing SOLIDWORKS 2022 Tutorial is written to assist students, designers, engineers and professionals who are new to SOLIDWORKS. The text provides a step-by-step, project based learning approach. It also contains information and examples on the five categories in the CSWA exam. The book is divided into four sections. Chapters 1 - 5 explore the SOLIDWORKS User Interface and CommandManager, Document and System properties, simple and complex parts and assemblies, proper design intent, design tables, configurations, multi-sheet, multi-view drawings, BOMs, and Revision tables using basic and advanced features. In chapter 6 you will create the final robot assembly. The physical components and corresponding Science, Technology, Engineering and Math (STEM) curriculum are available from Gears Educational Systems. All assemblies and components for the final robot assembly are provided. Chapters 7 - 10 prepare you for the Certified Associate - Mechanical Design (CSWA) exam. The certification indicates a foundation in and apprentice knowledge of 3D CAD and engineering practices and principles. Chapter 11 covers the benefits of additive manufacturing (3D printing), how it differs from subtractive manufacturing, and its features. You will also learn the terms and technology used in low cost 3D printers. Follow the step-by-step instructions and develop multiple assemblies that combine over 100 extruded machined parts and components. Formulate the skills to create, modify and edit sketches and solid features. Learn the techniques to reuse features, parts and assemblies through symmetry, patterns, copied components, apply proper design intent, design tables and configurations. Learn by doing, not just by reading. Desired outcomes and usage competencies are listed for each chapter. Know your objective up front. Follow the steps in each chapter to achieve your design goals. Work between multiple documents, features, commands, custom properties and document properties that represent how engineers and designers utilize SOLIDWORKS in industry.
Download or read book Learning SOLIDWORKS 2024 written by Randy Shih and published by SDC Publications. This book was released on 2024-03 with total page 543 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Teaches beginners how to use SOLIDWORKS with easy to understand tutorials • Features a simple robot design used as a project throughout the book • Covers modeling, gear creation, linkage analysis, assemblies, simulations and 3D animation • Available with an optional robot kit • Includes a chapter introducing you to 3D printing This book will teach you everything you need to know to start using SOLIDWORKS 2024 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the SOLIDWORKS interface and its basic tools right away. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of SOLIDWORKS's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using SOLIDWORKS. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanisms, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the second to last chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. Finally, in the last chapter, the author introduces you to 3D printing. You will learn the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. Being able to turn your designs into physical objects will open up a whole new world of possibilities to you. There are many books that show you how to perform individual tasks with SOLIDWORKS, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Learning SOLIDWORKS 2023 written by Randy Shih and published by SDC Publications. This book was released on 2023-03-27 with total page 545 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Teaches beginners how to use SOLIDWORKS with easy to understand tutorials • Features a simple robot design used as a project throughout the book • Covers modeling, gear creation, linkage analysis, assemblies, simulations and 3D animation • Available with an optional robot kit • Includes a chapter introducing you to 3D printing This book will teach you everything you need to know to start using SOLIDWORKS 2023 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the SOLIDWORKS interface and its basic tools right away. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of SOLIDWORKS's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using SOLIDWORKS. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanisms, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the second to last chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. Finally, in the last chapter, the author introduces you to 3D printing. You will learn the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. Being able to turn your designs into physical objects will open up a whole new world of possibilities to you. There are many books that show you how to perform individual tasks with SOLIDWORKS, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Learning SOLIDWORKS 2021 written by Shih, Randy and published by SDC Publications. This book was released on with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using SOLIDWORKS 2021 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the SOLIDWORKS interface and its basic tools right away. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of SOLIDWORKS's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using SOLIDWORKS. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanisms, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the second to last chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. Finally, in the last chapter, the author introduces you to 3D printing. You will learn the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. Being able to turn your designs into physical objects will open up a whole new world of possibilities to you. There are many books that show you how to perform individual tasks with SOLIDWORKS, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Learning SOLIDWORKS 2020 written by Randy Shih and published by SDC Publications. This book was released on 2020-02 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using SOLIDWORKS 2020 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the SOLIDWORKS interface and its basic tools right away. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of SOLIDWORKS's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using SOLIDWORKS. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanisms, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the second to last chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. Finally, in the last chapter, the author introduces you to 3D printing. You will learn the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. Being able to turn your designs into physical objects will open up a whole new world of possibilities to you. There are many books that show you how to perform individual tasks with SOLIDWORKS, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Learning SOLIDWORKS 2021 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2021-03 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Making Embedded Systems written by Elecia White and published by "O'Reilly Media, Inc.". This book was released on 2011-10-25 with total page 329 pages. Available in PDF, EPUB and Kindle. Book excerpt: Interested in developing embedded systems? Since they donâ??t tolerate inefficiency, these systems require a disciplined approach to programming. This easy-to-read guide helps you cultivate a host of good development practices, based on classic software design patterns and new patterns unique to embedded programming. Learn how to build system architecture for processors, not operating systems, and discover specific techniques for dealing with hardware difficulties and manufacturing requirements. Written by an expert whoâ??s created embedded systems ranging from urban surveillance and DNA scanners to childrenâ??s toys, this book is ideal for intermediate and experienced programmers, no matter what platform you use. Optimize your system to reduce cost and increase performance Develop an architecture that makes your software robust in resource-constrained environments Explore sensors, motors, and other I/O devices Do more with less: reduce RAM consumption, code space, processor cycles, and power consumption Learn how to update embedded code directly in the processor Discover how to implement complex mathematics on small processors Understand what interviewers look for when you apply for an embedded systems job "Making Embedded Systems is the book for a C programmer who wants to enter the fun (and lucrative) world of embedded systems. Itâ??s very well writtenâ??entertaining, evenâ??and filled with clear illustrations." â??Jack Ganssle, author and embedded system expert.
Download or read book Robotics in STEM Education written by Myint Swe Khine and published by Springer. This book was released on 2017-07-10 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes recent approaches in advancing STEM education with the use of robotics, innovative methods in integrating robotics in school subjects, engaging and stimulating students with robotics in classroom-based and out-of-school activities, and new ways of using robotics as an educational tool to provide diverse learning experiences. It addresses issues and challenges in generating enthusiasm among students and revamping curricula to provide application focused and hands-on approaches in learning . The book also provides effective strategies and emerging trends in using robotics, designing learning activities and how robotics impacts the students’ interests and achievements in STEM related subjects. The frontiers of education are progressing very rapidly. This volume brought together a collection of projects and ideas which help us keep track of where the frontiers are moving. This book ticks lots of contemporary boxes: STEM, robotics, coding, and computational thinking among them. Most educators interested in the STEM phenomena will find many ideas in this book which challenge, provide evidence and suggest solutions related to both pedagogy and content. Regular reference to 21st Century skills, achieved through active collaborative learning in authentic contexts, ensures the enduring usefulness of this volume. John Williams Professor of Education and Director of the STEM Education Research Group Curtin University, Perth, Australia
Download or read book Parametric Modeling with SOLIDWORKS 2021 written by Randy Shih and published by SDC Publications. This book was released on 2021-03 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: Parametric Modeling with SOLIDWORKS 2021 contains a series of seventeen tutorial style lessons designed to introduce SOLIDWORKS 2021, solid modeling and parametric modeling techniques and concepts. This book introduces SOLIDWORKS 2021 on a step-by-step basis, starting with constructing basic shapes, all the way through to the creation of assembly drawings and motion analysis. This book takes a hands on, exercise intensive approach to all the important parametric modeling techniques and concepts. Each lesson introduces a new set of commands and concepts, building on previous lessons. The lessons guide the user from constructing basic shapes to building intelligent solid models, assemblies and creating multi-view drawings. This book also covers some of the more advanced features of SOLIDWORKS 2021, including how to use the SOLIDWORKS Design Library, basic motion analysis, collision detection and analysis with SimulationXpress. The exercises in this book cover the performance tasks that are included on the Certified SOLIDWORKS Associate (CSWA) Examination. Reference guides located at the front of the book and in each chapter show where these performance tasks are covered. This book also introduces you to the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. 3D printing makes it easier than ever for anyone to start turning their designs into physical objects and by the end of this book you will be ready to start printing out your own designs.
Download or read book Parametric Modeling with SOLIDWORKS 2022 written by Randy Shih and published by SDC Publications. This book was released on with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Parametric Modeling with SOLIDWORKS 2022 contains a series of seventeen tutorial style lessons designed to introduce SOLIDWORKS 2022, solid modeling and parametric modeling techniques and concepts. This book introduces SOLIDWORKS 2022 on a step-by-step basis, starting with constructing basic shapes, all the way through to the creation of assembly drawings and motion analysis. This book takes a hands on, exercise intensive approach to all the important parametric modeling techniques and concepts. Each lesson introduces a new set of commands and concepts, building on previous lessons. The lessons guide the user from constructing basic shapes to building intelligent solid models, assemblies and creating multi-view drawings. This book also covers some of the more advanced features of SOLIDWORKS 2022, including how to use the SOLIDWORKS Design Library, basic motion analysis, collision detection and analysis with SimulationXpress. The exercises in this book cover the performance tasks that are included on the Certified SOLIDWORKS Associate (CSWA) Examination. Reference guides located at the front of the book and in each chapter show where these performance tasks are covered. This book also introduces you to the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. 3D printing makes it easier than ever for anyone to start turning their designs into physical objects and by the end of this book you will be ready to start printing out your own designs.
Download or read book Learning Autodesk Inventor 2022 written by Randy Shih and published by SDC Publications. This book was released on 2021-08 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2022 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.
Download or read book Robotics Vision and Control written by Peter Corke and published by Springer. This book was released on 2011-09-05 with total page 572 pages. Available in PDF, EPUB and Kindle. Book excerpt: The author has maintained two open-source MATLAB Toolboxes for more than 10 years: one for robotics and one for vision. The key strength of the Toolboxes provide a set of tools that allow the user to work with real problems, not trivial examples. For the student the book makes the algorithms accessible, the Toolbox code can be read to gain understanding, and the examples illustrate how it can be used —instant gratification in just a couple of lines of MATLAB code. The code can also be the starting point for new work, for researchers or students, by writing programs based on Toolbox functions, or modifying the Toolbox code itself. The purpose of this book is to expand on the tutorial material provided with the toolboxes, add many more examples, and to weave this into a narrative that covers robotics and computer vision separately and together. The author shows how complex problems can be decomposed and solved using just a few simple lines of code, and hopefully to inspire up and coming researchers. The topics covered are guided by the real problems observed over many years as a practitioner of both robotics and computer vision. It is written in a light but informative style, it is easy to read and absorb, and includes a lot of Matlab examples and figures. The book is a real walk through the fundamentals of robot kinematics, dynamics and joint level control, then camera models, image processing, feature extraction and epipolar geometry, and bring it all together in a visual servo system. Additional material is provided at http://www.petercorke.com/RVC
