Download or read book Laboratory Testing of Bulk Vitrified Low Activity Waste Forms to Support the 2005 Integrated Disposal Facility Performance Assessment Erratum written by and published by . This book was released on 2016 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E.M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.
Download or read book Corrosion of Metal Inclusions In Bulk Vitrification Waste Packages Erratum written by and published by . This book was released on 2016 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report refers to or contains Kg values for glasses LAWA44, LAWB45 and LAWC22 affected by calculations errors as identified by Papathanassiu et al. (2011). The corrected Kg values are reported in an erratum included in the revised version of the original report. The revised report can be referenced as follows: Pierce E.M. et al. (2004) Waste Form Release Data Package for the 2005 Integrated Disposal Facility Performance Assessment. PNNL-14805 Rev. 0 Erratum. Pacific Northwest National Laboratory, Richland, WA, USA.
Download or read book Waste Form Qualification Compliance Strategy for Bulk Vitrification written by and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Bulk Vitrification System is being pursued to assist in immobilizing the low-activity tank waste from the 53 million gallons of radioactive waste in the 177 underground storage tanks on the Hanford Site. To demonstrate the effectiveness of the bulk vitrification process, a research and development facility known as the Demonstration Bulk Vitrification System (DBVS) is being built to demonstrate the technology. Specific performance requirements for the final packaged bulk vitrification waste form have been identified. In addition to the specific product-performance requirements, performance targets/goals have been identified that are necessary to qualify the waste form but do not lend themselves to specifications that are easily verified through short-term testing. Collectively, these form the product requirements for the DBVS. This waste-form qualification (WFQ) strategy document outlines the general strategies for achieving and demonstrating compliance with the BVS product requirements. The specific objectives of the WFQ activities are discussed, the bulk vitrification process and product control strategy is outlined, and the test strategy to meet the WFQ objectives is described. The DBVS product performance targets/goals and strategies to address those targets/goals are described. The DBVS product-performance requirements are compared to the Waste Treatment and Immobilization Plant immobilized low-activity waste product specifications. The strategies for demonstrating compliance with the bulk vitrification product requirements are presented.
Download or read book ILAW Glass Testing for Disposal at IDF written by and published by . This book was released on 2011 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document reports the results of the testing of phase 1 ORP LAW (low activity waste) glasses, also identified as enhanced LAW glasses. Testing involved are SPFT (Single Pass Flow Through), VHT (Vapor Hydration Test), and PCT (Product Consistency Test), along with the analytical tests (XRD and SEM-EDS). This report contains the data of the high waste loading ORP LAW glasses that will be used for the performance assessment of the IDF (Integrated Disposal Facility).
Download or read book TECHNICAL ASSESSMENT OF BULK VITRIFICATION PROCESS PRODUCT FOR TANK WASTE TREATMENT AT THE DEPARTMENT OF ENERGY HANFORD SITE written by P. S. SCHAUS and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: At the U.S. Department of Energy (DOE) Hanford Site, the Waste Treatment Plant (WTP) is being constructed to immobilize both high-level waste (IUW) for disposal in a national repository and low-activity waste (LAW) for onsite, near-surface disposal. The schedule-controlling step for the WTP Project is vitrification of the large volume of LAW, current capacity of the WTP (as planned) would require 50 years to treat the Hanford tank waste, if the entire LAW volume were to be processed through the WTP. To reduce the time and cost for treatment of Hanford Tank Waste, and as required by the Tank Waste Remediation System Environmental Impact Statement Record of Decision and the Hanford Federal Facility Consent Agreement (Tn-Party Agreement), DOE plans to supplement the LAW treatment capacity of the WTP. Since 2002, DOE, in cooperation with the Environmental Protection Agency and State of Washington Department of Ecology has been evaluating technologies that could provide safe and effective supplemental treatment of LAW. Current efforts at Hanford are intended to provide additional information to aid a joint agency decision on which technology will be used to supplement the WTP. A Research, Development and Demonstration permit has been issued by the State of Washington to build and (for a limited time) operate a Demonstration Bulk Vitrification System (DBVS) facility to provide information for the decision on a supplemental treatment technology for up to 50% of the LAW. In the Bulk Vitrification (BV) process, LAW, soil, and glass-forming chemicals are mixed, dried, and placed in a refractory-lined box, Electric current, supplied through two graphite electrodes in the box, melts the waste feed, producing a durable glass waste-form. Although recent modifications to the process have resulted in significant improvements, there are continuing technical concerns.
Download or read book Laboratory Procedures for Waste Form Testing written by and published by . This book was released on 1994 with total page 49 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory.
Download or read book Feed Variability and Bulk Vitrification Glass Performance Assessment written by and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The supplemental treatment (ST) bulk vitrification process will obtain its feed, consisting of low-activity waste (LAW), from more than one source. One purpose of this letter report is to describe the compositional variability of the feed to ST. The other is to support the M-62-08 decision by providing a preliminary assessment of the effectiveness of bulk vitrification (BV), the process that has been selected to perform supplemental treatment, in handling the ST feed envelope. Roughly nine-tenths of the ST LAW feed will come from the Waste Treatment Plant (WTP) pretreatment. This processed waste is expected to combine (1) a portion of the same LAW feed sent to the WTP melters and (2) a dilute stream that is the product of the condensate from the submerged-bed scrubber (SBS) and the drainage from the electrostatic precipitator (WESP), both of which are part of the LAW off-gas system. The manner in which the off-gas-product stream is concentrated to reduce its volume, and the way in which the excess LAW and off-gas product streams are combined, are part of the interface between WTP and ST and have not been determined. This letter report considers only one possible arrangement, in which half of the total LAW is added to the off-gas product stream, giving an estimated ST feed stream from WTP. (Total LAW equals that portion of LAW sent to the WTP LAW vitrification plant (WTP LAW) plus the LAW not currently treatable in the LAW vitrification plant due to capacity limitations (excess)).
Download or read book GLASS FORMULATION TESTING TO INCREASE SULFATE INCORPORATION Final Report VSL 04R4960 1 Rev 0 2 28 05 Vitreous State Laboratory The Catholic University of American Washington written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: About 50 million gallons of high-level mixed waste is currently in storage in underground tanks at The United States Department of Energy's (DOE's) Hanford site in the State of Washington. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) will provide DOE's Office of River Protection (ORP) with a means of treating this waste by vitrification for subsequent disposal. The tank waste will be separated into low- and high-activity fractions, which will then be vitrified respectively into Immobilized Low Activity Waste (ILAW) and Immobilized High Level Waste (IHLW) products. The ILAW product will be disposed of in an engineered facility on the Hanford site while the IHLW product will be directed to the national deep geological disposal facility for high-level nuclear waste. The ILAW and IHLW products must meet a variety of requirements with respect to protection of the environment before they can be accepted for disposal. The Office of River Protection is currently examining options to optimize the Low Activity Waste (LAW) facility and the LAW glass waste form. One option under evaluation is to enhance the waste processing rate of the vitrification plant currently under construction. It is likely that the capacity of the LAW vitrification plant can be increased incrementally by implementation of a variety of low-risk, high-probability changes, either separately or in combination. These changes include: (1) Operating at the higher processing rates demonstrated at the LAW Pilot Melter; (2) Increasing the glass pool surface area within the existing external melter envelope; (3) Increasing plant availability; (4) Increasing the glass waste loading; (5) Removing sulfate from the LAW stream; (6) Operating the melter at slightly higher temperature; (7) Installing the third LAW melter into the WTP plant; and (8) Other smaller impact changes. The melter tests described in this report utilized blended feed (glass formers plus waste simulant) prepared by Optima Chemicals according to VSL specifications. Sufficient feed was prepared to produce over nineteen hundred kilograms of glass during melter tests. The nominal reductant concentration (stoichiometric ratio of 0.5 ≈ 1 mole sucrose per 16 mole NOx or 3 mole carbon per 4 mole NOx) was maintained in all the tests by the addition of sugar at VSL. The DM 10 was used to screen the optimized glass formulation with two alternative aluminum sources (kyanite and zeolite) over a wide range of target sulfur concentrations. Subsequently, based on the DM10 results, nine 12- to 34-hour DM100 tests were conducted; six with kyanite as the aluminum additive at glass sulfur concentrations ranging from 0.75 to 1.5 wt.% SO3, and the other three with zeolite as the aluminum additive at glass sulfur concentrations ranging from 0.75 to 1.5 wt. % SO3. The DM 100-WV melter was used in order to provide a direct comparison with the LAW tests previously conducted on the same melter. Key operating parameters such as glass temperature and production rate were held constant to investigate the sulfur incorporation into the glass and the effects of varying the aluminum additive source. The bubbling rate was adjusted to achieve a production rate of 2000 kg/m2/day with a near-complete cold cap (90-100% of melt surface covered with feed). Quantitative measurements of glass production rates, melter operating conditions (temperatures, pressures, power, flows, etc.), and off-gas characteristics (NOx, SO2, CO, particulate load and composition, and acid gases) were made for each test. Glass samples taken from the glass pool and the discharge chamber were inspected throughout testing to determine the limit of salt-free operation in the melter.
Download or read book Oak Ridge National Laboratory West End Treatment Facility Simulated Sludge Vitrification Demonstration Revision 1 written by and published by . This book was released on 1994 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Technologies are being developed by the US Department of Energy's (DOE) Nuclear Facility sites to convert hazardous and mixed wastes to a form suitable for permanent disposal. Vitrification, which has been declared the Best Demonstrated Available Technology for high-level radioactive waste disposal by the EPA, is capable of producing a highly durable wasteform that minimizes disposal volumes through organic destruction, moisture evaporation, and porosity reduction. However, this technology must be demonstrated over a range of waste characteristics, including compositions, chemistries, moistures, and physical characteristics to ensure that it is suitable for hazardous and mixed waste treatment. These wastes are typically wastewater treatment sludges that are categorized as listed wastes due to the process origin or organic solvent content, and usually contain only small amounts of hazardous constituents. The Oak Ridge National Laboratory's (ORNL) West End Treatment Facility's (WETF) sludge is considered on of these representative wastes. The WETF is a liquid waste processing plant that generates sludge from the biodenitrification and precipitation processes. An alternative wasteform is needed since the waste is currently stored in epoxy coated carbon steel tanks, which have a limited life. Since this waste has characteristics that make it suitable for vitrification with a high likelihood of success, it was identified as a suitable candidate by the Mixed Waste Integrated Program (MWIP) for testing at CU. The areas of special interest with this sludge are (1) minimum nitrates, (2) organic destruction, and (3) waste water treatment sludges containing little or no filter aid.
Download or read book Enhanced LAW Glass Correlation Phase 1 written by and published by . This book was released on 2016 with total page 199 pages. Available in PDF, EPUB and Kindle. Book excerpt: About 50 million gallons of high-level mixed waste is currently stored in underground tanks at the United States Department of Energy's (DOE's) Hanford site in the State of Washington. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) will provide DOE's Office of River Protection (ORP) with a means of treating this waste by vitrification for subsequent disposal. The tank waste will be separated into low- and high-activity waste fractions, which will then be vitrified respectively into Immobilized Low Activity Waste (ILAW) and Immobilized High Level Waste (IHLW) products. The ILAW product will be disposed in an engineered facility on the Hanford site while the IHLW product is designed for acceptance into a national deep geological disposal facility for high-level nuclear waste. The ILAW and IHLW products must meet a variety of requirements with respect to protection of the environment before they can be accepted for disposal. Acceptable glass formulations for vitrification of Hanford low activity waste (LAW) must meet a variety of product quality, processability, and waste loading requirements. To this end, The Vitreous State Laboratory (VSL) at The Catholic University of America (CUA) developed and tested a number of glass formulations during Part A, Part B1 and Part B2 of the WTP development program. The testing resulted in the selection of target glass compositions for the processing of eight of the Phase I LAW tanks. The selected glass compositions were tested at the crucible scale to confirm their compliance with ILAW performance requirements. Duramelter 100 (DM100) and LAW Pilot Melter tests were then conducted to demonstrate the viability of these glass compositions for LAW vitrification at high processing rates.
Download or read book Low level Waste Vitrification Pilot scale System Need Report written by and published by . This book was released on 1996 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report examines the need for pilot-scale testing in support of the low-level vitrification facility at Hanford. In addition, the report examines the availability of on-site facilities to contain a pilot-plant. It is recommended that a non-radioactive pilot-plant be operated for extended periods. In addition, it is recommended that two small-scale systems, one processing radioactive waste feed and one processing a simulated waste feed be used for validation of waste simulants. The actual scale of the pilot-plant will be determined from the technologies included in conceptual design of the plant. However, for the purposes of this review, a plant of 5 to 10 metric ton/day of glass production was assumed. It is recommended that a detailed data needs package and integrated flowsheet be developed in FY95 to clearly identify data requirements and identify relationships with other TWRS elements. A pilot-plant will contribute to the reduction of uncertainty in the design and initial operation of the vitrification facility to an acceptable level. Prior to pilot-scale testing, the components will not have been operated as an integrated system and will not have been tested for extended operating periods. Testing for extended periods at pilot-scale will allow verification of the flowsheet including the effects of recycle streams. In addition, extended testing will allow evaluation of wear, corrosion and mechanical reality of individual components, potential accumulations within the components, and the sensitivity of the process to operating conditions. Also, the pilot facility will provide evidence that the facility will meet radioactive and nonradioactive environmental release limits, and increase the confidence in scale-up. The pilot-scale testing data and resulting improvements in the vitrification facility design will reduce the time required for cold chemical testing in the vitrification facility.
Download or read book Evaluating Long term Performance of in Situ Vitrified Waste Forms written by and published by . This book was released on 1992 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt: In situ vitrification (ISV) is an emerging technology for the remediation of hazardous and radioactive waste sites. The concept relies on the principle of Joule heating to raise the temperature of a soil between an array of electrodes above the melting temperature. After cooling, the melt solidifies into a massive glass and crystalline block similar to naturally occurring obsidian. Determining the long-term performance of ISV products in a changing regulatory environment requires a fundamental understanding of the mechanisms controlling the dissolution behavior of the material. A series of experiments was performed to determine the dissolution behavior of samples produced from the ISV processing of typical soils from the Idaho National Engineering Laboratory subsurface disposal area. Dissolution rate constant measurements were completed at 90[degrees]C over the pH range 2 to 11 for one sample obtained from a field test of the ISV process.
Download or read book INEL Test Plan for Evaluating Waste Assay Systems written by and published by . This book was released on 1996 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt: A test bed is being established at the Idaho National Engineering Laboratory (INEL) Radioactive Waste Management Complex (RWMC). These tests are currently focused on mobile or portable radioassay systems. Prior to disposal of TRU waste at the Waste Isolation Pilot Plant (WIPP), radioassay measurements must meet the quality assurance objectives of the TRU Waste Characterization Quality Assurance Program Plan. This test plan provides technology holders with the opportunity to assess radioassay system performance through a three-tiered test program that consists of: (a) evaluations using non-interfering matrices, (b) surrogate drums with contents that resemble the attributes of INEL-specific waste forms, and (c) real waste tests. Qualified sources containing a known mixture and range of radionuclides will be used for the non-interfering and surrogate waste tests. The results of these tests will provide technology holders with information concerning radioassay system performance and provide the INEL with data useful for making decisions concerning alternative or improved radioassay systems that could support disposal of waste at WIPP.
Download or read book Single Pass Flow Through SPFT Testing of Fluidized Bed Steam Reforming FBSR Waste Forms written by C. M. Jantzen and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Two samples of fluidized-bed steam reforming (FBSR) mineral waste form product were subjected to single-pass flow-through (SPFT) testing. Sample LAW 1123 resulted from pilot-scale FBSR processing with a Hanford Envelope A low-activity waste (LAW) simulant. Sample SBW 1173 resulted from pilot-scale FBSR processing with an Idaho National Laboratory (INL) simulant commonly referred to as sodium-bearing waste (SBW). The pilot-scale waste forms were made at the Science and Technology Applications Research (STAR) facility in Idaho Falls, Idaho. The durability of the two FBSR waste forms was assessed via the SPFT test in this study. Both samples were multiphase mineral waste forms, so the SPFT test results provide an overall release rate from the multiple mineral species in each sample and are dependent on the amount of each phase present and the mineralogy of the phases present. SPFT testing was performed at temperatures of 25, 40, 70, and 90 C on LAW 1123, while SBW 1173 was only tested at 70 and 90 C. The 70 and 90 C data were compared to each other and the LAW-1123 results were compared to previous testing performed by the Pacific Northwest National Laboratory (PNNL) on a LAW Envelope C (high organic content) waste simulant. The objectives of this study were to obtain forward dissolution rate data for both STAR FBSR bed products (using SPFT tests). Also, a qualitative comparison of the FBSR bed products to a glass waste form (specifically the low-activity reference material (LRM) glass) was performed. For these comparisons, the relative surface areas of the FBSR and glass products had to be measured. Due to the more porous and irregular surface of FBSR bed products, the surface area of the bed products was determined using the Brunauer, Emmett, and Teller (BET) measurement method. The surface area of a glass is much smoother and the calculated geometric surface area is typically used for determining dissolution behavior. Presently there are no specifications or standard release rates that the FBSR tested materials have to meet, e.g. the data from the FBSR testing is normally used during subsequent Performance Assessment (PA) calculations. Since a PA calculation is not part of this study, the LAW and SBW steam reforming samples were compared to each other, to previous LAW FBSR SPFT results, and to the results from the LRM reference glass. The experimental durability data generated from this study suggests that an FBSR mineral waste form product would be an adequate alternative form to borosilicate glass. The tested FBSR mineral waste forms showed normalized release rates for matrix elements such as Si to be more than 200X slower than the LRM glass. However, further durability testing and mineral phase information is recommended to further substantiate these findings.
Download or read book Hanford Low level Waste Process Chemistry Testing Data Package written by Harry D. Smith and published by . This book was released on 1996 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analysis of Machining and Machine Tools written by Steven Liang and published by Springer. This book was released on 2015-12-29 with total page 241 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides readers with the fundamental, analytical, and quantitative knowledge of machining process planning and optimization based on advanced and practical understanding of machinery, mechanics, accuracy, dynamics, monitoring techniques, and control strategies that they need to understanding machining and machine tools. It is written for first-year graduate students in mechanical engineering, and is also appropriate for use as a reference book by practicing engineers. It covers topics such as single and multiple point cutting processes; grinding processes; machine tool components, accuracy, and metrology; shear stress in cutting, cutting temperature and thermal analysis, and machine tool chatter. The second section of the book is devoted to “Non-Traditional Machining,” where readers can find chapters on electrical discharge machining, electrochemical machining, laser and electron beam machining, and biomedical machining. Examples of realistic problems that engineers are likely to face in the field are included, along with solutions and explanations that foster a didactic learning experience.
