Download or read book Investigation of Optical Loss Changes in Siloxane Polymer Waveguides During Thermal Curing and Aging written by Shashikant G. Hegde and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In high performance electronic systems, with increasing chip speed and larger number of processors, the system performance is being limited by off-chip metal interconnects. In such systems, polymer optical waveguides are being considered to replace electrical interconnects because of their high capacity for bandwidth and less constraints on interconnect length. The optical loss in the polymer optical waveguides is the key criterion used to evaluate their performance, and is significantly affected by thermal curing and aging. The evolution of degree-of-cure is determined from differential scanning calorimetry and compared to optical absorption from spectroscopy. Optical loss due to scattering mechanisms is related to local density fluctuations, which is studied using dielectric analysis. Based on the optical loss trends in uncladded and cladded waveguides, the underlying mechanisms for the optical loss variations are proposed and a cure process schedule to realize the lowest optical loss is recommended. Process-induced thermal stresses can also affect the polymer waveguide by introducing stress birefringence. The stress-optical coefficients of the siloxane polymer are extracted and employed in a numerical modeling method to determine the stress-induced birefringence in an optical waveguide system. The thermal-aging dependent optical loss is determined for waveguide samples at several different accelerated temperature conditions. To get the field-use conditions, the temperature distribution in the vicinity of the embedded laser and the polymer waveguide is determined. Using such thermal experimental data, the analytical reliability models were employed to relate the optical loss with time, and provide a practical way of determining whether the optical waveguides would perform within the optical loss budget during field-use conditions.

Download or read book Optical Attenuation in Siloxane Polymer Waveguides written by Shashikant Hegde and published by Lulu.com. This book was released on with total page 115 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hot Embossing written by Matthias Worgull and published by William Andrew. This book was released on 2009-09-28 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is an overview of replication technology for micro- and nanostructures, focusing on the techniques and technology of hot embossing, a scaleable and multi-purpose technology for the manufacture of devices such as BioMEMS and microfluidic devices which are expected to revolutionize a wide range of medical and industrial processes over the coming decade.The hot embossing process for replicating microstructures was developed by the Forschungszentrum Karlsruhe (Karlsruhe Institute of Technology) where the author is head of the Nanoreplication Group. Worgull fills a gap in existing information by fully detailing the technology and techniques of hot embossing. He also covers nanoimprinting, a process related to hot embossing, with examples of actual research topics and new applications in nanoreplication. A practical and theoretical guide to selecting the materials, machinery and processes involved in microreplication using hot embossing techniques Compares different replication processes such as: micro injection molding, micro thermoforming, micro hot embossing, and nanoimprinting Details commercially available hot embossing machinery and components like tools and mold inserts

Download or read book Silane Coupling Agents written by Edwin P. Plueddemann and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: * It has been rumored that a bumble bee has such aerodynamic deficiencies that it should be incapable of flight. Fiberglass-reinforced polymer com posites, similarly, have two (apparently) insurmountable obstacles to per formance: 1) Water can hydrolyze any conceivable bond between organic and inorganic phase, and 2) Stresses across the interface during temperature cycling (resulting from a mismatch in thermal expansion coefficients) may exceed the strength of one of the phases. Organofunctional silanes are hybrid organic-inorganic compounds that are used as coupling agents across the organic-inorganic interface to help overcome these two obstacles to composite performance. One of their functions is to use the hydrolytic action of water under equilibrium condi tions to relieve thermally induced stresses across the interface. If equilib rium conditions can be maintained, the two problems act to cancel each other out. Coupling agents are defined primarily as materials that improve the practical adhesive bond of polymer to mineral. This may involve an increase in true adhesion, but it may also involve improved wetting, rheology, and other handling properties. The coupling agent may also modify the inter phase region to strengthen the organic and inorganic boundary layers.

Download or read book Lab on Fiber Technology written by Andrea Cusano and published by Springer. This book was released on 2014-07-29 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on a research field that is rapidly emerging as one of the most promising ones for the global optics and photonics community: the “lab-on-fiber” technology. Inspired by the well-established "lab on-a-chip" concept, this new technology essentially envisages novel and highly functionalized devices completely integrated into a single optical fiber for both communication and sensing applications. Based on the R&D experience of some of the world's leading authorities in the fields of optics, photonics, nanotechnology, and material science, this book provides a broad and accurate description of the main developments and achievements in the lab-on-fiber technology roadmap, also highlighting the new perspectives and challenges to be faced. This book is essential for scientists interested in the cutting-edge fiber optic technology, but also for graduate students.

Download or read book Broadband Dielectric Spectroscopy written by Friedrich Kremer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 740 pages. Available in PDF, EPUB and Kindle. Book excerpt: Both an introductory course to broadband dielectric spectroscopy and a monograph describing recent dielectric contributions to current topics, this book is the first to cover the topic and has been hotly awaited by the scientific community.

Download or read book Industrial Photoinitiators written by W. Arthur Green and published by CRC Press. This book was released on 2010-04-22 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of photoinitiators in the UV curing process shows remarkable possibilities in myriad applications. Highlighting critical factors such as reactivity, cure speeds, and application details, Industrial Photoinitiators: A Technical Guide is a practical, accessible, industrially oriented text that explains the theory, describes the products, and

Download or read book Sol Gel Optics written by Lisa C. Klein and published by Springer Science & Business Media. This book was released on 2013-11-27 with total page 589 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sol--Gel--Optics encompasses numerous schemes for fabricating optical materials from gels -- materials such as bulk optics, optical waveguides, doped oxides for laser and nonlinear optics, gradient refractive index (GRIN) optics, chemical sensors, environmental sensors, and `smart' windows. Sol--Gel--Optics: Processing and Applications provides in-depth coverage of the synthesis and fabrication of these materials and discusses the optics related to microporous, amorphous, crystalline and composite materials. The reader will also find in this book detailed descriptions of new developments in silica optics, bulk optics, waveguides and thin films. Various applications to sensor and device technology are highlighted. For researchers and students looking for novel optical materials, processing methods or device ideas, Sol--Gel--Optics: Processing and Applications surveys a wide array of promising new avenues for further investigation and for innovative applications. (This book is the first in a new subseries entitled `Electronic Materials: Science and Technology).

Download or read book OFC 2002 written by and published by . This book was released on 2002 with total page 960 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sol Gel Technologies for Glass Producers and Users written by Michel Andre Aegerter and published by Springer Science & Business Media. This book was released on 2013-03-19 with total page 474 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sol-Gel Techniques for Glass Producers and Users provides technological information, descriptions and characterizations of prototypes, or products already on the market, and illustrates advantages and disadvantages of the sol-gel process in comparison to other methods. The first chapter entitled "Wet Chemical Technology" gives a summary of the basic principles of the sol-gel chemistry. The most promising applications are related to coatings. Chapter 2 describes the various "Wet Chemical Coating Technologies" from glass cleaning to many deposition and post-coating treatment techniques. These include patterning of coatings through direct or indirect techniques which have became very important and for which the sol-gel processing is particularly well adapted. Chapter 3 entitled "Bulk Glass Technologies" reports on the preparation of special glasses for different applications. Chapter 4 entitled "Coatings and Materials Properties" describes the properties of the different coatings and the sol-gel materials, fibers and powders. The chapter also includes a section dedicated to the characterization techniques especially applied to sol-gel coatings and products.

Download or read book Spatial Solitons written by Stefano Trillo and published by Springer Science & Business Media. This book was released on 2001-09-11 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt: Soliton-based concepts open the road for newly designed laser sources, new frequency converters and high-intensity laser-material interactions. Optical solitons as stable spatial patterns of complex nonlinear systems allow for the control of the diffraction of optical beams. Solitons also prevent unwanted chaotic behavior. Thus, solitary wave physics plays a significant role from modern optical physics to optical communication, optical switching, and optical storage. The book gives an updated overview of optical solitons and can serve as a reference and guide for advanced students and scientists working in the field and related areas of science where solitons are observed.

Download or read book High Performance Polymers and Engineering Plastics written by Vikas Mittal and published by John Wiley & Sons. This book was released on 2011-09-09 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes advances in synthesis, processing, and technology of environmentally friendly polymers generated from renewable resources. With contents based on a wide range of functional monomers and contributions from eminent researchers, this volume demonstrates the design, synthesis, properties and applications of plant oil based polymers, presenting an elaborate review of acid mediated polymerization techniques for the generation of green polymers. Chemical engineers are provided with state-of-the-art information that acts to further progress research in this direction.

Download or read book Chemistry and Technology of Cyanate Ester Resins written by I. Hamerton and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: After epoxy resins and polyimides, cyanate esters arguably form the most well-developed group of high-temperature, thermosetting polymers. They possess a number of desirable performance characteristics which make them of increasing technological importance, where their somewhat higher costs are acceptable. The principal end uses for cyanate esters are as matrix resins for printed wiring board laminates and structural composites. For the electronics markets, the low dielectric loss characteristics, dimen sional stability at molten solder temperatures and excellent adhesion to conductor metals at temperatures up to 250°C, are desirable. In their use in aerospace composites, unmodified cyanate esters offer twice the frac ture toughness of multifunctional epoxies, while achieving a service tem perature intermediate between epoxy and bis-maleimide capabilities. Applications in radome construction and aircraft with reduced radar signatures utilize the unusually low capacitance properties of cyanate esters and associated low dissipation factors. While a number of commercial cyanate ester monomers and prepoly mers are now available, to date there has been no comprehensive review of the chemistry and recent technological applications of this versatile family of resins. The aims of the present text are to present these in a com pact, readable form. The work is primarily aimed at materials scientists and polymer technologists involved in research and development in the chemical, electronics, aerospace and adhesives industries. It is hoped that advanced undergraduates and postgraduates in polymer chemistry and technology, and materials science/technology will find it a useful introduc tion and source of reference in the course of their studies.

Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2710 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Polymer Characterisation written by B.J. Hunt and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polymers continue to play an ever increasing role in the modern world. In fact it is quite inconceivable to most people that we could ever have existed of the increased volume and variety of materials without them. As a result currently available, and the diversity of their application, characterisation has become an essential requirement of industrial and academic laboratories in volved with polymeric materials. On the one hand requirements may come from polymer specialists involved in the design and synthesis of new materials who require a detailed understanding of the relationship between the precise molecular architecture and the properties of the polymer in order to improve its capabilities and range of applications. On the other hand, many analysts who are not polymer specialists are faced with the problems of analysing and testing a wide range of polymeric materials for quality control or material specification purposes. We hope this book will be a useful reference for all scientists and techno or industrial laboratories, logists involved with polymers, whether in academic and irrespective of their scientific discipline. We have attempted to include in one volume all of the most important techniques. Obviously it is not possible to do this in any great depth but we have encouraged the use of specific examples to illustrate the range of possibilities. In addition numerous references are given to more detailed texts on specific subjects, to direct the reader where appropriate. The book is divided into II chapters.

Download or read book Optical Fiber Sensor Technology written by L.S. Grattan and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: Environmental and chemical sensors in optical fiber sensor technology The nature of the environment in which we live and work, and the precarious state of many aspects of the natural environment, has been a major lesson for scientists over the last few decades. Public awareness of the issues involved is high, and often coupled with a scepticism of the ability of the scientist and engineer to provide an adequate, or even rapid solution to the preservation of the environment before further damage is done, and to achieve this with a mini mum of expenditure. Monitoring of the various aspects of the environment, whether it be external or internal to ourselves and involving chemical, physical or biomedical parameters is an essential process for the well-being of mankind and of the individual. Legis lative requirements set new standards for measurement and control all around us, which must be met by the most appropriate of the technologies available, commensurate with the costs involved. Optical fiber sensor technology has a major part to play in this process, both to complement existing technologies and to promote new solutions to difficult measurement issues. The developments in new sources and detectors covering wider ranges of the electromagnetic spectrum, with higher sensitivity, allow the use of techniques that some time ago would have been considered inappropriate or lacking in sufficient sensitivity.

Download or read book Clay Polymer Nanocomposites written by Khouloud Jlassi and published by Elsevier. This book was released on 2017-07-26 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt: Clay–Polymer Nanocomposites is a complete summary of the existing knowledge on this topic, from the basic concepts of synthesis and design to their applications in timely topics such as high-performance composites, environment, and energy issues. This book covers many aspects of synthesis such as in- situ polymerization within the interlamellar spacing of the clays or by reaction of pristine or pre-modified clays with reactive polymers and prepolymers. Indeed, nanocomposites can be prepared at industrial scale by melt mixing. Regardless the synthesis method, much is said in this book about the importance of theclay pre-modification step, which is demonstrated to be effective, on many occasions, in obtaining exfoliated nanocomposites. Clay–Polymer Nanocomposites reports the background to numerous characterization methods including solid state NMR, neutron scattering, diffraction and vibrational techniques as well as surface analytical methods, namely XPS, inverse gas chromatography and nitrogen adsorption to probe surface composition, wetting and textural/structural properties. Although not described in dedicated chapters, numerous X-ray diffraction patterns of clay–polymer nanocomposites and reference materials are displayed to account for the effects of intercalation and exfoliations of layered aluminosilicates. Finally, multiscale molecular simulation protocols are presenting for predicting morphologies and properties of nanostructured polymer systems with industrial relevance. As far as applications are concerned, Clay–Polymer Nanocomposites examines structural composites such as clay–epoxy and clay–biopolymers, the use of clay–polymer nanocomposites as reactive nanocomposite fillers, catalytic clay-(conductive) polymers and similar nanocomposites for the uptake of hazardous compounds or for controlled drug release, antibacterial applications, energy storage, and more. The most comprehensive coverage of the state of the art in clay–polymer nanocomposites, from synthesis and design to opportunities and applications Covers the various methods of characterization of clay–polymer nanocomposites - including spectroscopy, thermal analyses, and X-ray diffraction Includes a discussion of a range of application areas, including biomedicine, energy storage, biofouling resistance, and more