Download or read book Inverse Heat Conduction and Heat Exchangers written by Suvanjan Bhattacharyya and published by BoD – Books on Demand. This book was released on 2020-12-02 with total page 204 pages. Available in PDF, EPUB and Kindle. Book excerpt: A direct solution of the heat conduction equation with prescribed initial and boundary conditions yields temperature distribution inside a specimen. The direct solution is mathematically considered as a well-posed one because the solution exists, is unique, and continuously depends on input data. The estimation of unknown parameters from the measured temperature data is known as the inverse problem of heat conduction. An error in temperature measurement, thermal time lagging, thermocouple-cavity, or signal noise data makes stability a problem in the estimation of unknown parameters. The solution of the inverse problem can be obtained by employing the gradient or non-gradient based inverse algorithm. The aim of this book is to analyze the inverse problem and heat exchanger applications in the fields of aerospace, mechanical, applied mechanics, environment sciences, and engineering.
Download or read book Inverse Heat Conduction written by James V. Beck and published by James Beck. This book was released on 1985-10-02 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: Here is the only commercially published work to deal with the engineering problem of determining surface heat flux and temperature history based on interior temperature measurements. Provides the analytical techniques needed to arrive at otherwise difficult solutions, summarizing the findings of the last ten years. Topics include the steady state solution, Duhamel's Theorem, ill-posed problems, single future time step, and more.
Download or read book Inverse Heat Transfer written by M. Necat Ozisik and published by Routledge. This book was released on 2018-05-02 with total page 349 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces the fundamental concepts of inverse heat transfer problems. It presents in detail the basic steps of four techniques of inverse heat transfer protocol, as a parameter estimation approach and as a function estimation approach. These techniques are then applied to the solution of the problems of practical engineering interest involving conduction, convection, and radiation. The text also introduces a formulation based on generalized coordinates for the solution of inverse heat conduction problems in two-dimensional regions.
Download or read book Solving Direct and Inverse Heat Conduction Problems written by Jan Taler and published by Springer Science & Business Media. This book was released on 2010-04-16 with total page 890 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a solution for direct and inverse heat conduction problems, discussing the theoretical basis for the heat transfer process and presenting selected theoretical and numerical problems in the form of exercises with solutions. The book covers one-, two- and three dimensional problems which are solved by using exact and approximate analytical methods and numerical methods. An accompanying CD-Rom includes computational solutions of the examples and extensive FORTRAN code.
Download or read book Inverse Heat Conduction written by Hamidreza Najafi and published by John Wiley & Sons. This book was released on 2023-03-02 with total page 355 pages. Available in PDF, EPUB and Kindle. Book excerpt: Inverse Heat Conduction A comprehensive reference on the field of inverse heat conduction problems (IHCPs), now including advanced topics, numerous practical examples, and downloadable MATLAB codes. The First Edition of the classic book Inverse Heat Conduction: III-Posed Problems, published in 1985, has been used as one of the primary references for researchers and professionals working on IHCPs due to its comprehensive scope and dedication to the topic. The Second Edition of the book is a largely revised version of the First Edition with several all-new chapters and significant enhancement of the previous material. Over the past 30 years, the authors of this Second Edition have collaborated on research projects that form the basis for this book, which can serve as an effective textbook for graduate students and as a reliable reference book for professionals. Examples and problems throughout the text reinforce concepts presented. The Second Edition continues emphasis from the First Edition on linear heat conduction problems with revised presentation of Stolz, Function Specification, and Tikhonov Regularization methods, and expands coverage to include Conjugate Gradient Methods and the Singular Value Decomposition method. The Filter Matrix concept is explained and embraced throughout the presentation and allows any of these solution techniques to be represented in a simple explicit linear form. Two direct approaches suitable for non-linear problems, the Adjoint Method and Kalman Filtering, are presented, as well as an adaptation of the Filter Matrix approach applicable to non-linear heat conduction problems. In the Second Edition of Inverse Heat Conduction: III-Posed Problems, readers will find: A comprehensive literature review of IHCP applications in various fields of engineering Exact solutions to several fundamental problems for direct heat conduction problems, the concept of the computational analytical solution, and approximate solution methods for discrete time steps using superposition of exact solutions which form the basis for the IHCP solutions in the text IHCP solution methods and comparison of many of these approaches through a common suite of test problems Filter matrix form of IHCP solution methods and discussion of using filter-form Tikhonov regularization for solving complex IHCPs in multi-layer domain with temperature-dependent material properties Methods and criteria for selection of the optimal degree of regularization in solution of IHCPs Application of the filter concept for solving two-dimensional transient IHCP problems with multiple unknown heat fluxes Estimating the heat transfer coefficient, h, for lumped capacitance body and bodies with temperature gradients Bias in temperature measurements in the IHCP and correcting for temperature measurement bias Inverse Heat Conduction is a must-have resource on the topic for mechanical, aerospace, chemical, biomedical, or metallurgical engineers who are active in the design and analysis of thermal systems within the fields of manufacturing, aerospace, medical, defense, and instrumentation, as well as researchers in the areas of thermal science and computational heat transfer.
Download or read book Theory and Applications of Heat Transfer in Humans 2 Volume Set written by Devashish Shrivastava and published by John Wiley & Sons. This book was released on 2018-07-02 with total page 897 pages. Available in PDF, EPUB and Kindle. Book excerpt: An authoritative guide to theory and applications of heat transfer in humans Theory and Applications of Heat Transfer in Humans 2V Set offers a reference to the field of heating and cooling of tissue, and associated damage. The author—a noted expert in the field—presents, in this book, the fundamental physics and physiology related to the field, along with some of the recent applications, all in one place, in such a way as to enable and enrich both beginner and advanced readers. The book provides a basic framework that can be used to obtain ‘decent’ estimates of tissue temperatures for various applications involving tissue heating and/or cooling, and also presents ways to further develop more complex methods, if needed, to obtain more accurate results. The book is arranged in three sections: The first section, named ‘Physics’, presents fundamental mathematical frameworks that can be used as is or combined together forming more complex tools to determine tissue temperatures; the second section, named ‘Physiology’, presents ideas and data that provide the basis for the physiological assumptions needed to develop successful mathematical tools; and finally, the third section, named ‘Applications’, presents examples of how the marriage of the first two sections are used to solve problems of today and tomorrow. This important text is the vital resource that: Offers a reference book in the field of heating and cooling of tissue, and associated damage. Provides a comprehensive theoretical and experimental basis with biomedical applications Shows how to develop and implement both, simple and complex mathematical models to predict tissue temperatures Includes simple examples and results so readers can use those results directly or adapt them for their applications Designed for students, engineers, and other professionals, a comprehensive text to the field of heating and cooling of tissue that includes proven theories with applications. The author reveals how to develop simple and complex mathematical models, to predict tissue heating and/or cooling, and associated damage.
Download or read book Inverse Heat Transfer written by Helcio R.B. Orlande and published by CRC Press. This book was released on 2021-03-24 with total page 317 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces the fundamental concepts of inverse heat transfer solutions and their application for solving problems in convective, conductive, radiative, and multi-physics problems. Inverse Heat Transfer: Fundamentals and Applications, Second Edition includes techniques within the Bayesian framework of statistics for solution of inverse problems. By modernizing the classic work of the late Professor M. Necat Ozisik and adding new examples and problems, this new edition provides a powerful tool for instructors, researchers, and graduate students studying thermal-fluid systems and heat transfer. FEATURES Introduces the fundamental concepts of inverse heat transfer Presents in systematic fashion the basic steps of powerful inverse solution techniques Develops inverse techniques of parameter estimation, function estimation, and state estimation Applies these inverse techniques to the solution of practical inverse heat transfer problems Shows inverse techniques for conduction, convection, radiation, and multi-physics phenomena Helcio R. B. Orlande is a Professor of Mechanical Engineering at the Federal University of Rio de Janeiro (UFRJ), where he was the Department Head from 2006 to 2007.
Download or read book Emerging Topics in Heat Transfer written by Qiuwang Wang and published by WIT Press. This book was released on 2013-11-06 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented in ten edited chapters this book encompasses important emerging topics in heat transfer equipment, particularly heat exchangers. The chapters have all been selected by invitation only. Advances in high temperature equipment and small scale devices continue to be important as the involved heat transfer and related phenomena are often complex in nature and different mechanisms like heat conduction, convection, turbulence, thermal radiation and phase change as well as chemical reactions may occur simultaneously. The book treats various operating problems, like fouling, and highlights applications in heat exchangers and gas turbine cooling. In engineering design and development, reliable and accurate computational methods are required to replace or complement expensive and time consuming experimental trial and error work. Tremendous advancements in knowledge and competence have been achieved during recent years due to improved computational solution methods for non-linear partial differential equations, turbulence modelling advancement and developments of computers and computing algorithms to achieve efficient and rapid simulations. The chapters of the book thoroughly present such advancement in a variety of applications.
Download or read book Fundamental Principles of Heat Transfer written by Stephen Whitaker and published by Elsevier. This book was released on 2013-10-22 with total page 575 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamental Principles of Heat Transfer introduces the fundamental concepts of heat transfer: conduction, convection, and radiation. It presents theoretical developments and example and design problems and illustrates the practical applications of fundamental principles. The chapters in this book cover various topics such as one-dimensional and transient heat conduction, energy and turbulent transport, forced convection, thermal radiation, and radiant energy exchange. There are example problems and solutions at the end of every chapter dealing with design problems. This book is a valuable introductory course in heat transfer for engineering students.
Download or read book Innovative Heat Exchangers written by Hans-Jörg Bart and published by Springer. This book was released on 2017-12-30 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: This accessible book presents unconventional technologies in heat exchanger design that have the capacity to provide solutions to major concerns within the process and power-generating industries. Demonstrating the advantages and limits of these innovative heat exchangers, it also discusses micro- and nanostructure surfaces and micro-scale equipment, and introduces pillow-plate, helical and expanded metal baffle concepts. It offers step-by-step worked examples, which provide instructions for developing an initial configuration and are supported by clear, detailed drawings and pictures. Various types of heat exchangers are available, and they are widely used in all fields of industry for cooling or heating purposes, including in combustion engines. The market in 2012 was estimated to be U$ 42.7 billion and the global demand for heat exchangers is experiencing an annual growth of about 7.8 %. The market value is expected to reach U$ 57.9 billion in 2016, and approach U$ 78.16 billion in 2020. Providing a valuable introduction to students and researchers, this book offers clear and concise information to thermal engineers, mechanical engineers, process engineers and heat exchanger specialists.
Download or read book Heat Conduction written by M. Necati Özışık and published by John Wiley & Sons. This book was released on 1993-03-22 with total page 716 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Second Edition for the standard graduate level course in conduction heat transfer has been updated and oriented more to engineering applications partnered with real-world examples. New features include: numerous grid generation--for finding solutions by the finite element method--and recently developed inverse heat conduction. Every chapter and reference has been updated and new exercise problems replace the old.
Download or read book Heat Conduction written by Vyacheslav Vikhrenko and published by BoD – Books on Demand. This book was released on 2011-11-30 with total page 366 pages. Available in PDF, EPUB and Kindle. Book excerpt: The content of this book covers several up-to-date approaches in the heat conduction theory such as inverse heat conduction problems, non-linear and non-classic heat conduction equations, coupled thermal and electromagnetic or mechanical effects and numerical methods for solving heat conduction equations as well. The book is comprised of 14 chapters divided into four sections. In the first section inverse heat conduction problems are discuss. The first two chapters of the second section are devoted to construction of analytical solutions of nonlinear heat conduction problems. In the last two chapters of this section wavelike solutions are attained.The third section is devoted to combined effects of heat conduction and electromagnetic interactions in plasmas or in pyroelectric material elastic deformations and hydrodynamics. Two chapters in the last section are dedicated to numerical methods for solving heat conduction problems.
Download or read book Heat Transfer written by Salim Newaz Kazi and published by BoD – Books on Demand. This book was released on 2023-02 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces the fundamentals, enhancements, applications, and modeling of heat transfer phenomena. Topics covered include heat transfer equations and applications in the estimation of heat energy transportation, heat transfer in specific applications, microchannel flow, condensation of refrigerants in modified heat exchanger tubes, alteration of tube surface texture for augmentation of heat transfer, boiling, etc. Also considered are fouling mitigation approaches to prolong heat exchanger operation, as well as tube coatings, heat exchanger digital twins, and various surface alteration techniques. Double-pass solar air heating and phenomena including heat transfer through thin liquid film and surface texture alteration for boiling heat transfer are discussed.
Download or read book Inverse Heat Transfer Fundamentals and Applications written by M. Necat Ozisik and published by CRC Press. This book was released on 2000-08-22 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Heat Transfer written by Aziz Belmiloudi and published by BoD – Books on Demand. This book was released on 2011-02-14 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past few decades there has been a prolific increase in research and development in area of heat transfer, heat exchangers and their associated technologies. This book is a collection of current research in the above mentioned areas and describes modelling, numerical methods, simulation and information technology with modern ideas and methods to analyse and enhance heat transfer for single and multiphase systems. The topics considered include various basic concepts of heat transfer, the fundamental modes of heat transfer (namely conduction, convection and radiation), thermophysical properties, computational methodologies, control, stabilization and optimization problems, condensation, boiling and freezing, with many real-world problems and important modern applications. The book is divided in four sections : "Inverse, Stabilization and Optimization Problems", "Numerical Methods and Calculations", "Heat Transfer in Mini/Micro Systems", "Energy Transfer and Solid Materials", and each section discusses various issues, methods and applications in accordance with the subjects. The combination of fundamental approach with many important practical applications of current interest will make this book of interest to researchers, scientists, engineers and graduate students in many disciplines, who make use of mathematical modelling, inverse problems, implementation of recently developed numerical methods in this multidisciplinary field as well as to experimental and theoretical researchers in the field of heat and mass transfer.
Download or read book Solving Direct and Inverse Heat Conduction Problems written by Jan Taler and published by Springer. This book was released on 2006-10-18 with total page 889 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a solution for direct and inverse heat conduction problems, discussing the theoretical basis for the heat transfer process and presenting selected theoretical and numerical problems in the form of exercises with solutions. The book covers one-, two- and three dimensional problems which are solved by using exact and approximate analytical methods and numerical methods. An accompanying CD-Rom includes computational solutions of the examples and extensive FORTRAN code.
Download or read book Inverse Heat Transfer Problems written by Oleg M. Alifanov and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph presents a systematic treatment of the theory of the propagation of transient electromagnetic fields (such as optical pulses) through dielectric media which exhibit both dispersion a.nd absorption. The work divides naturally into two parts. Part I presents a summary of the fundamental theory of the radiation and propagation of rather general electromagnetic waves in causal, linear media which are homogeneous and isotropic but which otherwise have rather general dispersive and absorbing properties. In Part II, we specialize to the propagation of a plane, transient electromagnetic field in a homogeneous dielectric. Although we have made some contributions to the fundamental theory given in Part I, most of the results of our own research appear in Part II. The purpose of the theory presented in Part II is to predict and to explain in explicit detail the dynamics of the field after it has propagated far enough through the medium to be in the mature-dispersion regime. It is the subject of a classic theory, based on the research conducted by A. Sommerfeld and L.
