Download or read book CAD CAM Robotics and Factories of the Future 90 written by Suren N. Dwivedi and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 593 pages. Available in PDF, EPUB and Kindle. Book excerpt: According to the Concurrent Engineering Research Center (CERC) at West Virginia University, "the concurrent engineering (CE) is a rapid simultaneous approach where research and development, design, manufacturing and support are carried out in parallel". The mission of concurrent engineering is to reduce time to market, improve total quality and lower cost for products or systems developed and supported by large organizations. The purpose of the concurrent design methodology is to let the designer know the consequences of his design decisions in the manufacturing and assembly stages as well as in subsequent operations. Design for manufacture and assembly, design for reliability and testability, CAD/CAM/CAE, knowledge based systems, cost analysis and advanced material technology are the major constituents of concurrent engineering. The need for concurrent engineering can be justified from the fact that in every production cycle, the design phase approximately takes 5 to 10% of the total cycle, but overall it influences 80% of the production cycle. This volume contains articles from a wide spectrum dealing with concepts of concurrent engineering. The importance of the knowledge-based systems in the CE environment is significant as they provide the common platform to achieve the same level of expertise to the designers and manufacturers throughout the organization for the specific task. Their role in "do it right the first time" is very important in providing aid to the designers and manufacturers to optimize the design and manufacturing setups for a cost effectiveness and reduced production time.
Download or read book CAD CAM Robotics and Factories of the Future written by Dipak Kumar Mandal and published by Springer. This book was released on 2016-01-05 with total page 831 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is based on the proceedings of the 28th International Conference on CAD/CAM, Robotics and Factories of the Future. This book specially focuses on the positive changes made in the field of robotics, CAD/CAM and future outlook for emerging manufacturing units. Some of the important topics discussed in the conference are product development and sustainability, modeling and simulation, automation, robotics and handling systems, supply chain management and logistics, advanced manufacturing processes, human aspects in engineering activities, emerging scenarios in engineering education and training. The contents of this set of proceedings will prove useful to both researchers and practitioners.
Download or read book CAD CAM Robotics and Factories of the Future written by S. Narayanan and published by Alpha Science Int'l Ltd.. This book was released on 2006 with total page 1112 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presents state-of-the-art research and case studies from over 150 Design & Manufacturing professionals across the globe in the areas of CAD/CAM; Product Design; Rapid Prototyping and Tooling; Manufacturing Processes; Micromachining and Miniaturisation; Mechanism and Robotics; Artificial Intelligence; and Material Handling Systems.
Download or read book CAD CAM Robotics and Factories of the Future written by Birendra Prasad and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is about automation - automation in design, automation in manufacturing, and automation in production. Automation is essen tial for increased productivity of quality products at reduced costs. That even partial or piecemeal automation of a production facility can deliver dramatic improvements in productivity has been amply demon strated in many a real-life situation. Hence, currently, great ef forts are being devoted to research and development of general as well special methodologies of and tools for automation. This volume re ports on some of these methodologies and tools. In general terms, methodologies for automation can be divided into two groups. There are situations where a process, whether open-loop or closed-loop, is fairly clearly understood. In such a situation, it is possible to create a mathematical model and to prescribe a mathe matical procedure to optimize the output. If such mathematical models and procedures are computationally tractable, we call the correspond ing automation - algorithmic or parametric programming. There is, however, a second set of situations which include process es that are not well understood and the available mathematical models are only approximate and discrete. While there are others for which mathematical procedures are so complex and disjoint that they are computationally intractable. These are the situations for which heuristics are quite suitable for automation. We choose to call such automation, knowledge-based automation or heuristic programming.
Download or read book Computer Integrated Manufacturing Proceedings Of The 3rd International Conference In 2 Volumes written by Robert Gay and published by World Scientific. This book was released on 1995-07-10 with total page 1596 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book E business written by Brian Stanford-Smith and published by IOS Press. This book was released on 2000 with total page 1164 pages. Available in PDF, EPUB and Kindle. Book excerpt: How can the Internet and world wide web improve my long-term competitive advantage? This book helps answer this question by providing a better understanding of the technologies, their potential applications and the ways they can be used to add value for customers, support new strategies, and improve existing operations. It is not just about e-commerce but the broader theme of e-business which affects products, business processes, strategies, and relationships with customers, suppliers, distributors and competitors. To cover future trends, the editors have collected papers from authors operating at the frontiers of the developments so the reader can more appreciate the directions in which these technologies are heading. The resulting 165 essays have been collated into ten sections, which have been grouped in three parts: key issues, applications areas and applications, tools and technologies. A business rarely makes radical changes but is constantly making adjustments to circumstances. Businesses must now adapt to the global implications of the Internet and world wide web. This book hopes to aid awareness of the implications so that the changes are managed wisely.
Download or read book Precision Product Process Design and Optimization written by Sanjay S. Pande and published by Springer. This book was released on 2018-04-18 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces readers to various tools and techniques for the design of precision, miniature products, assemblies and associated manufacturing processes. In particular, it focuses on precision mechanisms, robotic devices and their control strategies, together with case studies. In the context of manufacturing process, the book highlights micro/nano machining/forming processes using non-conventional energy sources such as lasers, EDM (electro-discharge machining), ECM (electrochemical machining), etc. Techniques for achieving optimum performance in process modeling, simulation and optimization are presented. The applications of various research tools such as FEM (finite element method), neural networks, genetic algorithms, etc. to product-process design and optimization are illustrated through case studies. The state-of-the-art material presented here provides valuable directions for product development and future research work in this area. The contents of this book will be of use to researchers and industry professionals alike.
Download or read book Planning Design and Analysis of Cellular Manufacturing Systems written by A.K. Kamrani and published by Newnes. This book was released on 1995-04-11 with total page 401 pages. Available in PDF, EPUB and Kindle. Book excerpt: Leading researchers in the field of cellular manufacturing systems from academia and industry have contributed to this volume. The book aims to report the latest developments and address the central issues in the design and implementation of cellular manufacturing systems. Cellular Manufacturing (CM) is one of the major concepts used in the design of flexible manufacturing systems. CM, also known as group production or family programming, can be described as a manufacturing technique that produces families of parts within a single line or cell of machines. The first part of the book describes various techniques for design and modeling of cellular manufacturing systems. The second part is concerned with performance measure and analysis, followed by a section which presents the applications of artifical intelligence and computer tools in cellular manufacturing systems.
Download or read book Robotics and Factories of the Future 87 written by R. Radharamanan and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 868 pages. Available in PDF, EPUB and Kindle. Book excerpt: The papers presented at the Second International Conference on Robotics and Factories of the Future held in San Diego, California, USA during July 28-31, 1987 are compiled in this volume. Over two hundred participants attended the conference, made technical presentations and discussed about various aspects of manufacturing, robotics and factories of the future. The number of papers published in this volume and the number of unpublished presentations at the conference indicates the evidance of growing interest in the areas of CAD/CAM, robotics and their role in future factories. The conference consisted of five plenary sessions, twenty three technical sessions, workshops, and exhibits from local industries and educational institutions. I wish to acknowledge with many thanks the contributions of all the authors who presented their work at the conference and submitted the manuscripts for publication. It is also my pleasure to acknowledge the role of keynote, banquet, and plenary sessions speakers whose contributions added greatly to the success of the conference. My sincere thanks to all session chairmen. I wish that the series of the International Conferences on Robotics and Factories of the Future which was initiated in 1984 in Charlotte, North Carolina will have a major impact on the use of robots and computers in the automated factories of the future.
Download or read book European Control Conference 1995 written by and published by European Control Association. This book was released on 1995-09-05 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the European Control Conference 1995, Rome, Italy 5-8 September 1995
Download or read book Project Modelling in Construction written by Norman Fisher and published by Thomas Telford. This book was released on 1997 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt: A review of the development of object oriented modelling and of the competitive advantages and pitfalls. This work reports on the computer visualisation for use in project design and planning, and examines the process of using a computer to manage the interaction between professional consultants and the project.
Download or read book Balanced Automation Systems written by Luis M. Camarinha-Matos and published by Springer. This book was released on 2013-06-05 with total page 465 pages. Available in PDF, EPUB and Kindle. Book excerpt: Towards Balanced Automation The concept. Manufacturing industries worldwide are facing tough challenges as a consequence of the globalization of economy and the openness of the markets. Progress of the economic blocks such as the European Union, NAFTA, and MERCOSUR, and the global agreements such as GATT, in addition to their obvious economic and social consequences, provoke strong paradigm shifts in the way that the manufacturing systems are conceived and operate. To increase profitability and reduce the manufacturing costs, there is a recent tendency towards establishing partnership links among the involved industries, usually between big industries and the networks of components' suppliers. To benefit from the advances in technology, similar agreements are being established between industries and universities and research institutes. Such an open tete-cooperation network may be identified as an extended enterprise or a virtual enterprise. In fact, the manufacturing process is no more carried out by a single enterprise, rather each enterprise is just a node that adds some value (a step in the manufacturing chain) to the cooperation network of enterprises. The new trends create new scenarios and technological challenges, especially to the Small and Medium size Enterprises (SMEs) that clearly comprise the overwhelming majority of manufacturing enterprises worldwide. Under the classical scenarios, these SMEs would have had big difficulties to access or benefit from the state of the art technology, due to their limited human, financial, and material resources.
Download or read book Integrated Manufacturing Systems Engineering written by Pierre Ladet and published by Springer. This book was released on 2013-06-29 with total page 301 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern manufacturing systems must be engineered as any other complex systems, especially in the context of their integration. The book first presents the all-embracing concept of the Extended Enterprise as way of inter-enterprise integration. It then focusses on Enterprise Engineering methods and tools to address intra-enterprise integration using a model-based approach. Business process modelling and re-engineering isssues are particularly discussed and tools presented. Formal specification and Petri net-based analysis methods for manufacturing systems complete the set of tools for Enterprise Engineering. Coordination and integration issues of manufacturing systems and their business processes are then covered and examples of integration platforms presented. Finally, standardization and pre-standardization issues related to enterprise modelling and integration conclude the book.
Download or read book Deadlock Resolution in Computer Integrated Systems written by MengChu Zhou and published by CRC Press. This book was released on 2018-10-08 with total page 693 pages. Available in PDF, EPUB and Kindle. Book excerpt: Complex computer-integrated systems offer enormous benefits across a wide array of applications, including automated production, transportation, concurrent software, and computer operating systems, computer networks, distributed database systems, and many other automated systems. Yet, as these systems become more complex, automated, distributed, and computing-intensive, the opportunity for deadlock issues rises exponentially. Deadlock modeling, detection, avoidance, and recovery are critical to improving system performance. Deadlock Resolution in Computer-Integrated Systems is the first text to summarize and comprehensively treat this issue in a systematic manner. Consisting of contributions from prominent researchers in the field, this book addresses deadlock-free models and scheduling, detection and recovery methods, the formulation of dynamic control policies, and comparison and industrial benchmark studies that evaluate various approaches. The editors lay the foundation for exploring deadlock issues with a typical example of an automated manufacturing process, illustrating three primary modeling methods (digraphs, Petri nets, and automata) and comparing their respective advantages and disadvantages. Providing all of the important models and resolution approaches, this book is the complete guide for electrical and control engineers and manufacturing, intelligent, and network systems designers to prevent and manage deadlock issues in their systems.
Download or read book Balanced Automation Systems II written by Luis M. Camarinha-Matos and published by Springer. This book was released on 2013-06-29 with total page 534 pages. Available in PDF, EPUB and Kindle. Book excerpt: xiv box for Balanced Automation, research in this area is still young and emerging. In our opinion, the development of hybrid balanced solutions to cope with a variety of automation levels and manual approaches, is a much more challenging research problem than the search for a purely automatic solution. Various research activities described in this book illustrate some of these challenges through the development proposals, assisting tools, and initial results. In certain chapters however, the balancing aspects are not yet achieved in the research area, but their inclusion in this book is intended to give a broader and more comprehensive perspective of the multiple areas involved. One important aspect to be noticed is the extension and application of the concept of balanced automation to all areas of the manufacturing enterprise. Clearly, the need for a "balanced" approach is not restricted to the shop floor components, rather it applies to all other areas, as illustrated by the wide spectrum of research contributions found in this book. For instance, the need for an appropriate integration of multiple systems and their perspectives is particularly important for the implantation of virtual enterprises. Although both the BASYS'95 and the BASYS'96 conferences have provided important contributions, approaches, and tools for the implantation of balanced automation systems, there are a number of areas that require further research: .
Download or read book Advances In Mobile Robotics Proceedings Of The Eleventh International Conference On Climbing And Walking Robots And The Support Technologies For Mobile Machines written by Lino Marques and published by World Scientific. This book was released on 2008-08-29 with total page 1309 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides state-of-the-art scientific and engineering research findings and developments in the area of mobile robotics and associated support technologies. It contains peer-reviewed articles presented at the CLAWAR 2008 conference. Robots are no longer confined to industrial manufacturing environments; rather, a great deal of interest is invested in the use of robots outside the factory environment. The CLAWAR conference series, established as a high-profile international event, acts as a platform for dissemination of research and development findings to address the current interest in mobile robotics in meeting the needs of mankind in various sectors of the society. These include personal care, public health, and services in the domestic, public and industrial environments. The editors of the book have extensive research experience and publications in the area of robotics in general, and in mobile robotics specifically.
Download or read book Impact of risk factors and techniques in lean manufacturing written by Dr. Chandan Deep Singh and published by BookRix. This book was released on 2018-01-18 with total page 39 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lean Manufacturing is defined as efficient approach to identifying and eliminating waste (non–value add activities) through regular improvement flowing the product in the pull of the customer in reach of perfection. Lean manufacturing is often simply "lean", is a systematical method for the leave out of waste ("Muda") within a manufacturing system. Lean also takes into account waste created through overwhelm ("Muri") and waste created through imperfection in workloads ("Mura"). Working from the angle of the client who consumes a product, "value" is any action or process that a customer want to pay for. “ To solve the problem of waste, Lean Manufacturing has number of tools at its disposal. These include continuous process improvement the ‘5 Ways’ and mistake-proofing. Thus it can be seen as taking a very similar approach to other improvement procedure.”
