Download or read book Internal Friction and Young s Modulus Measurements in Zr 2 5Nb Alloy Doped with Hydrogen written by Z-L Pan and published by . This book was released on 1992 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: The presence of hydrides is an important factor in assessing the potential for delayed hydride cracking in Zr-2.5Nb alloys, and consequently, the terminal solid solubility (TSS) of hydrogen in the material is an important parameter. In pure zirconium doped with hydrogen, the TSS is marked by a dissolution peak of internal friction on heating and a truncated precipitation peak associated with hydride nucleation on cooling. These phenomena occur only at low frequencies and are accompanied in torsion pendulum studies by autotwisting of the sample (or zero-point drift) that stops abruptly at the TSS. Neither the dissolution/precipitation peaks nor the autotwisting phenomena are observed in Zr-2.5Nb. However, the TSS is also marked by an abrupt change in the slope of Young's modulus as a function of temperature. This phenomenon is observed regardless of the frequency (in the range 1 Hz to 120 kHz) and in both pure zirconium and Zr-2.5Nb alloys. The reasons for the absence of the dissolution/precipitation peak in Zr-2.5Nb alloys are discussed and the use of Young's modulus changes to investigate the TSS of hydrogen and the hysteresis between heat-up and cool-down TSS curves is demonstrated.
Download or read book Internal friction and young s modulus measurements in zr 2 5nb alloy doped with hydrogen written by I. G. Ritchie and published by . This book was released on 1992 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium and Titanium Alloys written by Christoph Leyens and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an excellent reference for materials scientists and engineers needing to gain more knowledge about these engineering materials. Following introductory chapters on the fundamental materials properties of titanium, readers will find comprehensive descriptions of the development, processing and properties of modern titanium alloys. There then follows detailed discussion of the applications of titanium and its alloys in aerospace, medicine, energy and automotive technology.
Download or read book Proceedings of the Scientific Practical Conference Research and Development 2016 written by K. V. Anisimov and published by Springer. This book was released on 2017-12-04 with total page 715 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book relates to the III Annual Conference hosted by The Ministry of Education and Science of the Russian Federation in December 2016. This event has summarized, analyzed and discussed the interim results, academic outputs and scientific achievements of the Russian Federal Targeted Programme “Research and Development in Priority Areas of Development of the Russian Scientific and Technological Complex for 2014–2020.” It contains 75 selected papers from 6 areas considered priority by the Federal Targeted Programme: computer science, ecology & environment sciences; energy and energy efficiency; lifesciences; nanoscience & nanotechnology and transport & communications. The chapters report the results of the 3-years research projects supported by the Programme and finalized in 2016.
Download or read book Isostatic Pressing written by M. Koizumi and published by Springer Science & Business Media. This book was released on 1991-06-30 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt: This updated volume is intended as a reference text on the technology of hot and cold isostatic pressing together with applications for development of new materials.
Download or read book Introduction to Biomaterials written by J. L. Ong and published by Cambridge University Press. This book was released on 2014 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt: A succinct introduction to the field of biomaterials engineering, packed with practical insights.
Download or read book Superplasticity written by K. A. Padmanabhan and published by Springer. This book was released on 2018-12-08 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book combines the perspectives of materials science of Superplasticity, on the one hand, and those of design and mechanics, on the other, in order to provide a holistic view of materials, design, mechanics and performance which will lead to useful solutions of societal benefits, in addition to providing great intellectual challenges. After considering the experimental evidence for superplasticity in different classes of materials, the book discusses the physics-based models, along with their advantages and limitations. Then, the analyses for superplastic forming available in the framework of continuum mechanics, finite element analysis and numerical simulations are presented. Finally, the authors highlight some successful industrial applications. This book is recommended as a text book for courses on Superplasticity and as supplementary use for courses on Materials Processing, Manufacturing, High Temperature Deformation, Nanotechnology and Mechanical Behavior of Materials. Persons working in Department of Materials Science and Engineering, Physics, Mechanics, Mechanical Engineering, Aerospace Engineering, Metallurgy, Ceramics and Geo-sciences are likely to find the book to be useful. It is also recommended as a reference source for practicing engineers involved in the design, processing and manufacture of industrial components, which exploit the unique properties associated with superplastic materials.
Download or read book Buyology written by Martin Lindstrom and published by Currency. This book was released on 2010-02-02 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: NEW YORK TIMES BESTSELLER • “A fascinating look at how consumers perceive logos, ads, commercials, brands, and products.”—Time How much do we know about why we buy? What truly influences our decisions in today’s message-cluttered world? In Buyology, Martin Lindstrom presents the astonishing findings from his groundbreaking three-year, seven-million-dollar neuromarketing study—a cutting-edge experiment that peered inside the brains of 2,000 volunteers from all around the world as they encountered various ads, logos, commercials, brands, and products. His startling results shatter much of what we have long believed about what captures our interest—and drives us to buy. Among the questions he explores: • Does sex actually sell? • Does subliminal advertising still surround us? • Can “cool” brands trigger our mating instincts? • Can our other senses—smell, touch, and sound—be aroused when we see a product? Buyology is a fascinating and shocking journey into the mind of today's consumer that will captivate anyone who's been seduced—or turned off—by marketers' relentless attempts to win our loyalty, our money, and our minds.
Download or read book Sintering Applications written by Burcu Ertug and published by BoD – Books on Demand. This book was released on 2013-02-06 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering is one of the final stages of ceramics fabrication and is used to increase the strength of the compacted material. In the Sintering of Ceramics section, the fabrication of electronic ceramics and glass-ceramics were presented. Especially dielectric properties were focused on. In other chapters, sintering behaviour of ceramic tiles and nano-alumina were investigated. Apart from oxides, the sintering of non-oxide ceramics was examined. Sintering the metals in a controlled atmosphere furnace aims to bond the particles together metallurgically. In the Sintering of Metals section, two sections dealt with copper containing structures. The sintering of titanium alloys is another topic focused in this section. The chapter on lead and zinc covers the sintering in the field of extractive metallurgy. Finally two more chapter focus on the basics of sintering,i.e viscous flow and spark plasma sintering.
Download or read book Metallurgical and Ceramic Protective Coatings written by K.H. Stern and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: Surface engineering is an increasingly important field and consequently those involved need to be aware of the vast range of technologies available to modify surfaces. This text provides an up-to-date, authoritative exposition of the major condensed phase methods used for producing metallurgical and ceramic coatings. Each method is discussed thoroughly by an expert in that field. In each chapter the principle of the method, its range of applications and technical aspects involved are described. The book not only informs the reader about established technologies familiar only to specialists, but also details activity on the frontier of coating technology providing an insight into those potential technologies not yet fully developed but which should emerge in the near future.
Download or read book Hot Cracking Phenomena in Welds III written by John Lippold and published by Springer Science & Business Media. This book was released on 2011-05-03 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the third in a series of compendiums devoted to the subject of weld hot cracking. It contains 22 papers presented at the 3rd International Hot Cracking Workshop in Columbus, Ohio USA in March 2010. In the context of this workshop, the term “hot cracking” refers to elevated temperature cracking associated with either the weld metal or heat-affected zone. These hot cracking phenomena include weld solidification cracking, HAZ and weld metal liquation cracking, and ductility-dip cracking. The book is divided into three major sections based on material type; specifically aluminum alloys, steels, and nickel-base alloys. Each of these sections begins with a keynote paper from prominent researchers in the field: Dr. Sindo Kou from the University of Wisconsin, Dr. Thomas Böllinghaus from BAM and the University of Magdeburg, and Dr. John DuPont from Lehigh University. The papers contained within include the latest insight into the mechanisms associated with hot cracking in these materials and methods to prevent cracking through material selection, process modification, or other means. The three Hot Cracking Phenomena in Welds compendiums combined contain a total of 64 papers and represent the best collection of papers on the topic of hot cracking ever assembled.
Download or read book Handbook of Engineering Practice of Materials and Corrosion written by Jung-Chul (Thomas) Eun and published by Springer Nature. This book was released on 2020-09-04 with total page 885 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an in-depth guide to the practical aspects of materials and corrosion engineering in the energy and chemical industries. The book covers materials, corrosion, welding, heat treatment, coating, test and inspection, and mechanical design and integrity. A central focus is placed on industrial requirements, including codes, standards, regulations, and specifications that practicing material and corrosion engineers and technicians face in all roles and in all areas of responsibility. The comprehensive resource provides expert guidance on general corrosion mechanisms and recommends materials for the control and prevention of corrosion damage, and offers readers industry-tested best practices, rationales, and case studies.
Download or read book Recommended Values of Thermophysical Properties for Selected Commercial Alloys written by K. C. Mills and published by Woodhead Publishing. This book was released on 2002 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Biomaterials written by Joon B. Park and published by CRC Press. This book was released on 2002-08-29 with total page 267 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biomaterials: Principles and Applications offers a comprehensive review of all the major biomaterials in this rapidly growing field. In recent years, the role of biomaterials has been influenced considerably by advances in many areas of biotechnology and science, as well as advances in surgical techniques and instruments. Comprising chapters
Download or read book Hydroxyapatite and Other Calcium Orthophosphates written by Sergey V. Dorozhkin and published by Nova Science Publishers. This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the inorganic constituents of skeletons, dentine and the enamel of teeth in all vertebrates, as well as antlers of male deer, calcium orthophosphates (CaPO4) appear to be the key materials to sustain all life on Earth. Therefore, biologically relevant CaPO4 possess all the necessary features of the biomaterials, such as biocompatibility, bioactivity, bioresorbability, osteoconductivity, osteoinductivity, and appear to be non-toxic, non-inflammatory and non-immunogenic. In this book, the author presents current state-of-the-art applications of CaPO4 as bioceramics, deposits (coatings, films and layers) and in dentistry. Topics discussed include chemical composition and preparation, forming and shaping, sintering and firing for CaPO4-based bioceramics, chemical composition and preparation, pre- and post-deposition treatments for CaPO4-based deposits, followed by the detailed description of their major properties, biomedical applications and in vivo behavior. The detailed description of current CaPO4 applications in dentistry both for dental caries prevention and as various types of dental treatments is given in the last section of this book.
Download or read book The Corrosion of Zirconium written by L. E. Colteryahn and published by . This book was released on 1952 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Physical Metallurgy and processing of Intermetallic Compounds written by N.S. Stoloff and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt: The attractive physical and mechanical properties of ordered intermetallic alloys have been recognized since early in this century. However, periodic attempts to develop intermetallics for structural applications were unsuc cessful, due in major part to the twin handicaps of inadequate low-temper ature ductility or toughness, together with poor elevated-temperature creep strength. The discovery, in 1979, by Aoki and Izumi in Japan that small additions of boron caused a dramatic improvement in the ductility of Ni3Al was a major factor in launching a new wave of fundamental and applied research on intermetallics. Another important factor was the issuance in 1984 of a National Materials Advisory Board reported entitled "Structural Uses for Ductile Ordered Alloys," which identified numerous potential defense-related applications and proposed the launching of a coordinated development program to gather engineering property and processing data. A substantial research effort on titanium aluminides was already underway at the Air Force Materials Laboratory at Wright Patterson Air Force Base in Ohio and, with Air Force support, at several industrial and university laboratories. Smaller programs also were under way at Oak Ridge National Laboratory, under Department of Energy sponsorship. These research efforts were soon augmented in the United States by funding from Department of Defense agencies such as Office of Naval Research and Air Force Office of Scientific Research, and by the National Science Foundation.
