Download or read book Interlaminar Toughness of Fusion Bonded Thermoplastic Composites written by Francisco Raúl Sacchetti and published by . This book was released on 2017 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermoplastic composites are of increasing interest to the aerospace industry. The melt-processability of the thermoplastic matrix allows for fast manufacturing and assembling techniques, such as thermoforming and fusion bonding, which are also highly suitable for process automation. Fusion bonding involves heating of the interface between the parts to be bonded, application of pressure and finally cooling of the bonded parts. Even though successful commercial application of fusion bonding can already be found in the aerospace industry, a wider use requires additional developments in order to improve the predictability, reliability and robustness of fusion bonded joints. This first of all requires a better understanding of that what is perceived as ‘the load bearing capacity’, as measured by mechanical testing of fusion bonded joints.Two mechanisms that are essential for the generation of the load bearing capacity of fusion bonded joints are (i) intimate contact development, followed by (ii) the interdiffusion of polymer chains across the interface. Although these two mechanisms are a prerequisite for the development of a bond, they are not the only mechanisms that determine the performance of a fusion bonded joint. The physical state of the bond line and the structural morphology of the interface also plays an important role. The objective of this work is to identify, to analyse and, when possible, to quantify the relation between the physical state and the structural morphology induced by the fusion bonding process, and the resulting mechanical performance of the joints. For this purpose, the most relevant variations in physical state and structural morphology, as induced by the fusion bonding process, were identified. These factors were then isolated experimentally, and their effects on the interlaminar fracture toughness of the joints were studied.
Download or read book Interlaminar Fracture Toughness of Thermoplastic Composites written by and published by . This book was released on 1988 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Interlaminar Fracture Toughness of Thermoplastic Composites written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-05 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: Edge delamination tension and double cantilever beam tests were used to characterize the interlaminar fracture toughness of continuous graphite-fiber composites made from experimental thermoplastic polyimides and a model thermoplastic. Residual thermal stresses, known to be significant in materials processed at high temperatures, were included in the edge delamination calculations. In the model thermoplastic system (polycarbonate matrix), surface properties of the graphite fiber were shown to be significant. Critical strain energy release rates for two different fibers having similar nominal tensile properties differed by 30 to 60 percent. The reason for the difference is not clear. Interlaminar toughness values for the thermoplastic polyimide composites (LARC-TPI and polyimidesulfone) were 3 to 4 in-lb/sq in. Scanning electron micrographs of the EDT fracture surfaces suggest poor fiber/matrix bonding. Residual thermal stresses account for up to 32 percent of the strain energy release in composites made from these high-temperature resins. Hinkley, J. A. and Johnston, N. J. and Obrien, T. K. Langley Research Center RTOP 505-63-01-01...
Download or read book Thermoplastic Composite Materials written by Leif A. Carlsson and published by Elsevier Publishing Company. This book was released on 1991 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume provides a report on the structure, properties and thermomechanical response of thermoplastic composites. Emphasis is placed on the role of the matrix on thermomechanical behaviour in various composite microstructures.
Download or read book Interlaminar Fracture Toughness of Thermoplastic Composites written by J. A. Hinkley and published by . This book was released on 1986 with total page 33 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fusion Bonding of Polymer Composites written by C. Ageorges and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fusion bonding is one of the three methods available for joining composite and dissimilar materials. While the other two, mechanical fastening and adhesion bonding, have been the subject of wide coverage both in textbooks and monographs, fusion bonding is covered here substantially for the first time. Fusion bonding offers a number of advantages over traditional joining techniques and it is anticipated that its use will increase dramatically in the future because of the rise in the use of thermoplastic matrix composites and the growing necessity for recyclability of engineering assemblies. Fusion Bonding of Polymer Composites provides an in-depth understanding of the physical mechanisms involved in the fusion bonding process, covering such topics as: - heat transfer in fusion bonding; - modelling thermal degradation; - consolidation mechanisms; - crystallisation kinetics; - processing-microstructure-property relationship; - full-scale fusion bonding; - fusion bonding of thermosetting composite/thermoplastic composite and metal/thermoplastic joints. The book focuses on one practical case study using the resistance welding process. This example exposes the reader to the development of processing windows for a novel manufacturing process including the use of experimental test programmes and modelling strategies.
Download or read book High Performance Thermoplastics A Review of Neat Resin and Composite Properties written by Norman Joseph Johnston and published by . This book was released on 1987 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Moisture Effects on Mode I Interlaminar Fracture Toughness of a Graphite Fiber Thermoplastic Matrix Composite written by JP. Lucas and published by . This book was released on 1989 with total page 17 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mode I interlaminar fracture toughness was determined for a high-temperature thermoplastic matrix, intermediate modulus graphite fiber composite laminate. Interlaminar fracture toughness and fracture energy were determined for a unidirectional layup, continuous-fiber reinforced thermoplastic composite by using a nonconventional specimen. A short bar hybrid test specimen (HTS) was developed and used in this investigation to determine the effect of moisture on mode I delamination fracture toughness and critical strain energy release rate. Exposure of the thermoplastic composite laminate in a water bath for over 400 h had an insignificant effect on delamination fracture toughness. Moreover, a fractographic examination did not reveal effects of absorbed moisture on fracture surface morphology and failure processes. Fracture was characterized primarily by matrix decohesion and fiber pullout. There was, however, clear evidence of fracture mechanisms that contributed significantly to mode I fracture energy of the composite. Crack bridging by isolated, single fibers and fiber bundles was prevalent, particularly after a considerable degree of crack extension in the laminate. Translaminar, secondary microcracking was observed in the vicinity of the primary crack tip.
Download or read book High Performance Thermoplastic Resins and Their Composites written by Sylvie Beland and published by William Andrew. This book was released on 2012-12-02 with total page 185 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent developments in high performance thermoplastic resins and their composites are described in this book, and the benefits and limitations of these emerging materials are assessed for aerospace and other applications. Discussions on the performance of neat and continuous fiber reinforced thermoplastic resins in terms of their properties and environmental and chemical resistance are provided.
Download or read book Fusion Bonding of Thermoplastic Composites by Resistance Heating written by Roderic C. Don and published by . This book was released on 1989 with total page 35 pages. Available in PDF, EPUB and Kindle. Book excerpt: The efficiency of the welded joints is quantified by comparing test results to compression molded lap shear strength. A rapid increase in strength that asymptotically approaches the compression molded baseline is measured. In general, resistance welded APC-2 with PEEK film requires longer process times, with fiber motion occurring at the joint, to achieve a maximum lap shear strength of 44.8±7.6 MPa. The APC-2/PEI resistance welded specimens achieved a maximum strength of 35.9±1.0 Mpa in shorter time with no fiber motion. The baseline for the APC-2/PEI was determined from isothermal processing (1200 sec at 293°C) to be 43.6±3.8 MPa."
Download or read book Reinforced Thermoplastics written by P. G. Kelleher and published by iSmithers Rapra Publishing. This book was released on 1993 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report covers semi and non-crystalline thermoplastics, polymer blends and various classes of reinforcing fibres, and the properties which determine their suitability for specific applications. A detailed discussion of the injection moulding of reinforced thermoplastics includes the effect of processing on fibre distribution and breakage. An additional indexed section containing several hundred abstracts from the Rapra Polymer Library database provides useful references for further reading.
Download or read book Thermoplastic Composites written by Haibin Ning and published by Walter de Gruyter GmbH & Co KG. This book was released on 2021-11-08 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book covers various thermoplastic composites, including continuous and discontinuous fiber thermoplastic composites. It describes processing methods and explains the effect of different processing parameters on the structure and performance of thermoplastic composites. Characterization and mechanics of the composite are also discussed in the book.
Download or read book Sustainable Automotive Technologies 2012 written by Aleksandar Subic and published by Springer Science & Business Media. This book was released on 2012-03-02 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book on Sustainable Automotive Technologies aims to draw special attention to the research and practice focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. In particular, the book features incremental and radical technical advancements that are able to meet social, economic and environmental targets in both local and global contexts. These include original solutions to the problems of pollution and congestion, vehicle and public safety, sustainable vehicle design and manufacture, new structures and materials, new power-train technologies and vehicle concepts. In addition to vehicle technologies, the book is also concerned with the broader systemic issues such as sustainable supply chain systems, integrated logistics and telematics, and end-of-life vehicle management. It captures selected peer reviewed papers accepted for presentation at the 4th International Conference on Sustainable Automotive Technologies, ICSAT2012, held at the RMIT, Melbourne, Australia.
Download or read book Experimental investigation of interlaminar fracture toughness of carbon fiber thermoplastic and carbon fiber thermosetting composites by DCB specimens written by and published by . This book was released on 1991 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Non isothermal Strength Model Including Healing and Bondline Thickness Effect for Fusion Bonding of Thermoplastic Composites written by Min Chao and published by . This book was released on 1993 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Structure and Properties of Additive Manufactured Polymer Components written by Klaus Friedrich and published by Woodhead Publishing. This book was released on 2020-06-18 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structure and Properties of Additive Manufactured Polymer Components provides a state-of-the-art review from leading experts in the field who discuss key developments that have appeared over the last decade or so regarding the use of additive manufacturing (AM) methods in the production of neat and reinforced polymeric components. A major focus is given to materials science aspects, i.e., how the quality of the polymer preforms, the parameters of the chosen AM method, and how these factors can affect the microstructure and properties of the final product. The book not only covers production technologies and the relationship between processing, microstructure and fundamental properties of the produced parts, but also gives readers ideas on the use of AM polymer parts in medicine, automotive, aerospace, tribology, electronics, and more. Focuses on industrial aspects and applications Dedicated purely to recent advances in polymer composite additive manufacturing Emphasizes processing, structure and property relationships
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 702 pages. Available in PDF, EPUB and Kindle. Book excerpt:
