Download or read book Intelligent Compaction Control of Highway Embankment Soil in Kansas written by Farhana Rahman and published by . This book was released on 2008 with total page 107 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanistic pavement design procedures based on elastic layer theory require characterization of pavement layer materials including subgrade soil. This paper discusses the subgrade stiffness measurements obtained from a new compaction roller for compaction control on highway embankment projects in Kansas. Three test sections were compacted using a single, smooth steel drum intelligent compaction (IC) roller that compacts and simultaneously measures stiffness values of the compacted soil. Traditional compaction control measurements such as, density, in-situ moisture content, soil stiffness measurements using soil stiffness gage, surface deflection tests using the Light Falling Weight Deflectometer (LFWD) and Falling Weight Deflectometer (FWD), and penetration tests using a Dynamic Cone Penetrometer (DCP), were also done. The results show that the IC roller was able to identify the locations of lower soil stiffness in the spatial direction. Thus the IC roller can be used in proof rolling. IC roller stiffness showed sensitivity to the field moisture content indicating that moisture control during compaction is critical. No universal correlation was observed among the IC roller stiffness, soil gage stiffness, backcalculated subgrade moduli from the LFWD and FWD deflection data, and the California Bearing Ratio (CBR) obtained from DCP tests. The discrepancy seems to arise from the fact that different equipment were capturing response from different volumes of soil on the same test section. Analysis using the newly released Mechanistic-Empirical Pavement Design Guide (M-EPDG) shows that pavement rutting, roughness and asphalt base thickness are significantly influenced by the subgrade strength. "Target" modulus for compaction quality control can also be obtained by this analysis.
Download or read book Soil Stiffness Evaluation for Compaction Control of Cohesionless Embankments written by Farhana Rahman and published by . This book was released on 2008 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanistic pavement design procedures based on elastic layer theory require characterization of pavement layer materials including subgrade soil. This paper discusses the subgrade stiffness measurements obtained from a new compaction roller for compaction control on highway embankment projects in Kansas. Three test sections were compacted using a single, smooth steel drum intelligent compaction (IC) roller that compacts and simultaneously, measures stiffness values of the compacted soil. Traditional compaction control measurements such as, density, in-situ moisture content, stiffness measurements using a soil stiffness gage, surface deflection tests using the light falling weight deflectometer (LFWD) and falling weight deflectometer (FWD), and penetration tests using a dynamic cone penetrometer (DCP), were also done. The results show that the IC roller was able to identify the locations of lower soil stiffness in the spatial direction. Thus, an IC roller can be used in proof rolling. IC roller stiffness showed sensitivity to the field moisture content indicating that moisture control during compaction is critical. No universal correlation was observed among the IC roller stiffness, soil gage stiffness, back-calculated subgrade moduli from the LFWD and FWD deflection data, and the California bearing ratio obtained from DCP tests. The discrepancy seems to arise from the fact that different pieces of equipment were capturing response from different volumes of soil on the same test section.
Download or read book Intelligent Soil Compaction Systems written by Michael A. Mooney and published by Transportation Research Board. This book was released on 2010 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Report 676: Intelligent Soil Compaction Systems explores intelligent compaction, a new method of achieving and documenting compaction requirements. Intelligent compaction uses continuous compaction-roller vibration monitoring to assess mechanistic soil properties, continuous modification/adaptation of roller vibration amplitude and frequency to ensure optimum compaction, and full-time monitoring by an integrated global positioning system to provide a complete GPS-based record of the compacted area--
Download or read book Intelligent Compaction of Soils written by Philip Dunston and published by . This book was released on 2018-08-15 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes a study of intelligent compaction (IC) technologies, within the context of actual construction projects, for its potential as a component of INDOT's QC/QA for soils. The output from an IC-equipped roller compaction equipment is a real-time area mapping of the compacted lift stiffness as captured by the IC measure. Data was collected to evaluate the correlation between each of two IC measures-compaction meter value (CMV) and machine drive power (MDP)-and in situ embankment quality test measures, the chief in situ test being the dynamic cone penetrometer (DCP) test which INDOT uses for soil embankment acceptance testing. Researchers sought to understand how well the IC measures might assess embankment quality as currently evaluated by the in situ measures. Window-averaged IC measures were compared with the in situ DCP test points. For CMV, a variable correlation was found between the average CMV and DCP values from 74 in situ locations. Also, a limited head-to-head comparison of CMV and MDP with the in situ measures provided some indication that MDP should be studied further. Lessons were learned regarding the elimination of bias in future correlation studies, critical provisions to facilitate best data quality, and important aspects of data management. IC technology holds promise for monitoring the consistency of the soil compaction effort and flagging weak areas in real time during compaction operations. However, further insight is needed regarding the correlation of the DCP measure with both types of IC measures for various soil characterizations and field moisture conditions.
Download or read book Accelerated Implementation of Intelligent Compaction Technology for Embankment Subgrade Soils Aggregate Base and Asphalt Pavement Materials written by Jack H. Hansen and published by . This book was released on 2011 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intelligent compaction (IC) is an emerging technology, and for some applications it is mature enough for implementation in field compaction of pavement materials. The intent of this project is to realize the blueprint in the FHWA IC strategic plan. IC is a compaction technology used for materials including soils, aggregates, and asphalt mixtures, by using vibratory rollers equipped with the real-time kinematic (RTK) Global Positioning System (GPS), roller-integrated measurement system (normally accelerometer-based), feedback controls, and onboard real-time display of all IC measurements. IC technology can be used to produce uniformly compacted pavement products that perform better and last longer.
Download or read book Advanced Compaction Quality Control written by Carlos Zambrano and published by . This book was released on 2006-10-15 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evaluation of Intelligent Compaction Technology for Densification of Roadway Subgrades and Structural Layers written by and published by . This book was released on 2010 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Airfield and Highway Pavements written by Imad L. Al-Qadi and published by . This book was released on 2006 with total page 1072 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection contains 87 papers presented at the 2006 Airfield and Highway Pavements Specialty Conference, held in Atlanta, Georgia, April 30-May 3, 2006.
Download or read book Intelligent Compaction for Soils and Subbase Materials written by United States. Federal Highway Administration and published by . This book was released on 2010 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intelligent compaction (IC) is a construction method relatively new to the USA that uses modern vibratory rollers equipped IC components and technologies. Though used for decades in the rest of the world, the IC technology is less mature for its application in the asphalt compaction than its counter part for the soils and subbase compaction. Under the on-going FHWA/TPF IC studies, tremendous amount of knowledge has been gained on HMA IC. Components of asphalt IC include: double-drum IC rollers, roller measurement system, global position system (GPS) radio/receiver/base station, infrared temperature sensors, and integrated reporting system. Therefore, an asphalt IC roller can "adapt its behavior in response to varying situations and requirements" -being "intelligent"! There are many benefits using asphalt IC rollers. To name a few: proof rolling (mapping) to identify soft spots, achieve consistent roller patterns, monitor asphalt surface temperature (to keep up with the paver) and levels of compaction for 100% coverage area, and many more.
Download or read book Intelligent Compaction written by United States. Federal Highway Administration and published by . This book was released on 2013 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Technical Brief provides information that targets what an Executive level person in a state DOT would need to know to understand the advantages and reasons for using Intelligent Compaction equipment to construct highway aggregate bases and for construction of asphalt pavements. Use of this technology can improve pavement performance and extend the life of the pavement.
Download or read book Development of Stiffness based Specifications for In situ Embankment Compaction Quality Control written by Kansas. Department of Transportation. Bureau of Materials & Research and published by . This book was released on 2007 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: Compaction of embankment soils is a key factor influencing premature pavement distresses and bridge approach settlement. The current specifications of the Kansas Department of Transportation (KDOT) address embankment compaction in terms of density and moisture content. However, the implementation of performance-based specifications would require measuring mechanical properties of soil, such as stiffness, in addition to density. This is needed because soil stiffness is the parameter used to characterize the embankment soil in the design of pavement structures. The objectives of this study were to investigate the use of the Light Falling Weight Deflectometer (L-FWD) to measure in-situ soil stiffness and to investigate the feasibility of developing a stiffness-based specification for embankment soil compaction quality control. To achieve these objectives, soil stiffness values were measured at multiple locations along nine KDOT embankment projects using the Prima 100 L-FWD. Concurrent density and moisture measurements were also taken at select locations. Bulk soil samples were collected and remolded soil samples were used to measure the resilient moduli of the soils in the laboratory at varying density and moisture contents. For each soil, and at each combination moisture content and dry density level used in the laboratory tests, a constitutive model was derived from the laboratory resilient modulus data to capture the stress-dependent behavior of the soil. The constitutive model was then implemented in a finite element model of a semi-infinite soil half-space to compute the deflection at the surface of the half-space for a circular load. An equivalent elastic modulus for the soil half-space was back-estimated with the Boussinesque formula, for each combination moisture content and dry density. A regression model was then developed to relate the equivalent elastic modulus of the soil half-space to the dry density and moisture content of the soil. The regression model was used to predict the equivalent elastic moduli for the in-situ moisture contents and dry density values recorded during the field L-FWD tests. The predicted equivalent moduli were then compared to the moduli measured by the L-FWD. It was found that the equivalent moduli predicted from the results of the laboratory resilient modulus tests do not correlate with the in-situ soil stiffness measured with the L-FWD. This prevented the development of a quality control scheme based on laboratory measured resilient moduli. The high degree of spatial variability obtained for the in-situ moduli measured with the L-FWD prevented the development of a quality control scheme based on a control test strip.
Download or read book Intelligent Compaction for Asphalt Materials written by United States. Federal Highway Administration. Office of Pavement Technology and published by . This book was released on 2010 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intelligent compaction (IC) is a construction method relatively new to the USA that uses modern vibratory rollers equipped IC components and technologies. Though used for decades in the rest of the world, the IC technology is less mature for its application in the asphalt compaction than its counter part for the soils and subbase compaction. Under the on-going FHWA/TPF IC studies, tremendous amount of knowledge has been gained on HMA IC. Components of asphalt IC include: double-drum IC rollers, roller measurement system, global position system (GPS) radio/receiver/base station, infrared temperature sensors, and integrated reporting system. Therefore, an asphalt IC roller can "adapt its behavior in response to varying situations and requirements" -being "intelligent"! There are many benefits using asphalt IC rollers. To name a few: proof rolling (mapping) to identify soft spots, achieve consistent roller patterns, monitor asphalt surface temperature (to keep up with the paver) and levels of compaction for 100% coverage area, and many more.
Download or read book Intelligent Compaction for Roadway Soil and Asphalt Pavement written by Christopher M. Savan and published by . This book was released on 2014 with total page 118 pages. Available in PDF, EPUB and Kindle. Book excerpt: Conventional test methods for roadway compaction cover less than one percent of roadway; whereas, intelligent compaction (IC) offers a method to measure 100 percent of a roadway. IC offers the ability to increase compaction uniformity of soils and asphalt pavements, which leads to decreased maintenance costs and an extended service life. This thesis examines IC technology, how IC quality control and assurance specifications can encourage IC adoption, knowledge and use of IC through survey responses, and benefits and costs of IC. The surveys reveal that a majority of respondents from state departments of transportation have conducted IC demonstration projects, but questions about cost and willingness of policymakers to adopt IC remain a barrier to implementation. The benefit-cost analysis demonstrates that use of IC reduces compaction costs by as much as 54 percent and results in a $15,385 annual savings per lane mile throughout the roadway's life.
Download or read book Geosynthetics for Development of Transportation Infrastructures written by Sujit Kumar Dash and published by Frontiers Media SA. This book was released on 2021-05-05 with total page 107 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Principles and Practice of Ground Improvement written by Jie Han and published by John Wiley & Sons. This book was released on 2015-06-22 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gain a stronger foundation with optimal ground improvement Before you break ground on a new structure, you need to analyze the structure of the ground. Expert analysis and optimization of the geo-materials on your site can mean the difference between a lasting structure and a school in a sinkhole. Sometimes problematic geology is expected because of the location, but other times it's only unearthed once construction has begun. You need to be able to quickly adapt your project plan to include an improvement to unfavorable ground before the project can safely continue. Principles and Practice of Ground Improvement is the only comprehensive, up-to-date compendium of solutions to this critical aspect of civil engineering. Dr. Jie Han, registered Professional Engineer and preeminent voice in geotechnical engineering, is the ultimate guide to the methods and best practices of ground improvement. Han walks you through various ground improvement solutions and provides theoretical and practical advice for determining which technique fits each situation. Follow examples to find solutions to complex problems Complete homework problems to tackle issues that present themselves in the field Study design procedures for each technique to simplify field implementation Brush up on modern ground improvement technologies to keep abreast of all available options Principles and Practice of Ground Improvement can be used as a textbook, and includes Powerpoint slides for instructors. It's also a handy field reference for contractors and installers who actually implement plans. There are many ground improvement solutions out there, but there is no single right answer to every situation. Principles and Practice of Ground Improvement will give you the information you need to analyze the problem, then design and implement the best possible solution.
Download or read book Practices for Unbound Aggregate Pavement Layers written by E. Tutumluer and published by . This book was released on 2013 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: "TRB's National Cooperative Highway Research Program (NCHRP) Synthesis 445: Practices for Unbound Aggregate Pavement Layers consolidates information on the state-of-the-art and state-of-the-practice of designing and constructing unbound aggregate pavement layers. The report summarizes effective practices related to material selection, design, and construction of unbound aggregate layers to potentially improve pavement performance and longevity."--Publisher website.
Download or read book Design Guidelines for the Control of Blowing and Drifting Snow written by Ronald D. Tabler and published by Strategic Highway Research Program (Shrp). This book was released on 1994 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt:
