Download or read book Influence of Fiber Content on Mechanical Performance of SiC fiber reinforced Reaction bonded Silicon Nitride Composites written by and published by . This book was released on 1995 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Effects on the Mechanical Properties of SiC Fiber Reinforced Reaction Bonded Silicon Nitride Matrix SiC RBSN Composites written by R. T. Bhatt and published by . This book was released on 1988 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: The elevated temperature four-point flexural strength and the room temperature tensile and flexural strength properties after thermal shock were measured for ceramic composites consisting of 30 vol % uniaxially aligned 142 microns diameter SiC fibers in a reaction bonded Si3N4 matrix. The elevated temperature strengths were measured after 15 min of exposure in air at temperatures to 1400 C. The thermal shock treatment was accomplished by heating the composite in air for 15 min at temperatures to 1200 C and then quenching in water at 25 C. The results indicate no significant loss in strength properties either at temperature or after thermal shock when compared with the strength data for composites in the as-fabricated condition. (jes).
Download or read book Oxidation Effects on the Mechanical Properties of SiC Fiber Reinforced Reaction bonded Silicon Nitride Matrix Composites written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-09 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt: The room temperature mechanical properties of SiC fiber reinforced reaction bonded silicon nitride composites were measured after 100 hrs exposure at temperatures to 1400 C in nitrogen and oxygen environments. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers in a reaction bonded Si3N4 matrix. The results indicate that composites heat treated in a nitrogen environment at temperatures to 1400 C showed deformation and fracture behavior equivalent to that of the as-fabricated composites. Also, the composites heat treated in an oxidizing environment beyond 400 C yielded significantly lower tensile strength values. Specifically in the temperature range from 600 to 1000 C, composites retained approx. 40 percent of their as-fabricated strength, and those heat treated in the temperatures from 1200 to 1400 C retained 70 percent. Nonetheless, for all oxygen heat treatment conditions, composite specimens displayed strain capability beyond the matrix fracture stress; a typical behavior of a tough composite. Bhatt, Ramakrishna T. Glenn Research Center RTOP 510-01-0A...
Download or read book Effects of Interface Coating and Nitride Enhancing Additive on Properites of Hi Nicalon SiC Fiber Reinforced Reaction bonded Silicon Nitride Composites written by Ramakrishna T. Bhatt and published by . This book was released on 2000 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: Strong and tough Hi-Nicalon SiC fiber reinforced reaction-bonded silicon nitride matirix composites (SiC/RBSN) have been fabricated by the fiber lay-up approach. Commercially available uncoated and PBN, PBN/Si-rich PBN, and BN/SiC coated SiC Hi-Nicalon fiber tows were used as reinforcement. The composites contained ~24 vol % of aligned 14 ♯m diameter SiC fibers in a porous RBSN matrix. Both one- and two-dimensional composites were characterized. The effects of interface coating composition, and the nitridation enhancing additive, NiO, on the room temperature physical, tensile, and interfacial shear strenght properties of SiC/RBSN matrix composites were evaluated. Results indicate that all three coated fibers, the thickness of the coating decreased from the outer periphery to the interior of the tows, and that from 10 to 30 percent of the fibers were not covered with the interface coating.
Download or read book Influence of Interfacial Shear Strength on the Mechanical Properties of SiC Fiber Reinforced Reaction Bonded Silicon Nitride Matrix Composites written by and published by . This book was released on 1990 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: The influence of fiber/matrix interface microstructure and interfacial shear strength on the mechanical properties of a fiber-reinforced ceramic composite has been evaluated. The composite consisted of about 30 vol % uniaxially aligned 142 micron diameter SiC fibers (Textron SCS-6) in a reaction- bonded Si3N4 matrix (SiC/RBSN). The interface microstructure was varied by controlling the composite fabrication conditions and by heat treating the composite in an oxidizing environment. Interfacial shear strength was determined by the matrix crack spacing method. The results of microstructural examination indicate that the carbon-rich coating provided with the as-produced SiC fibers was stable in composites fabricated at 1200 C in a nitrogen or in a nitrogen plus 4 percent hydrogen mixture for 40 hr. However this coating degraded in composites fabricated at 1350 C in N2 + 4%H2 for 40 and 72 hr and also in composites heat treated in an oxidizing environment at 600 C for 100 hr after fabrication at 1200 C in a nitrogen. It was determined that degradation occurred by carbon removal which in turn had a strong influence on interfacial shear strength and other mechanical properties. Specifically, as the carbon coating was removed, the composite interfacial shear strength, primary elastic modulus, first matrix cracking stress, and ultimate tensile strength decreased, but the first matrix cracking strain remained nearly the same. Keywords: Ceramic matrix composites; Interfacial shear strength; Mechanical properties.
Download or read book Mechanical Properties of SiC Fiber Reinforced Reaction Bonded Si3N4 Composites written by R. T. Bhatt and published by . This book was released on 1985 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: The room temperature mechanical and physical properties of silicon carbide fiber-reinforced reaction-bonded silicon nitride composites (SiC/RBSN) have been evaluated. The composites contained similiar to 23 and similiar to 40 volume fraction of aligned 140 micron diameter chemically vapor deposited SiC fibers. Preliminary results for composites tensile and bend strengths and fracture strain indicate that the composites displayed excellent properties when compared with unreinforced RBSN of comparable porosity. Fiber volume fraction showed little influence on matrix first cracking strain did influence the stresses required for matrix first cracking and for ultimate composite fracture strength. It is suggested that by reducing matrix porosity and by increasing the volume fraction of the large diameter SiC fiber, it should be possible to further improve the composite stress at which the matrix first cracks. Keywords: Ceramic powders; Composite fabrication; Microstructure; Density; Axial bend and tensile; Strength; and Integrated shear strength.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 19th Annual Conference on Composites Advanced Ceramics Materials and Structures A Volume 16 Issue 4 written by John B. Wachtman and published by John Wiley & Sons. This book was released on 2009-09-28 with total page 606 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is part of the Ceramic Engineering and Science Proceeding (CESP) series. This series contains a collection of papers dealing with issues in both traditional ceramics (i.e., glass, whitewares, refractories, and porcelain enamel) and advanced ceramics. Topics covered in the area of advanced ceramic include bioceramics, nanomaterials, composites, solid oxide fuel cells, mechanical properties and structural design, advanced ceramic coatings, ceramic armor, porous ceramics, and more.
Download or read book Effects of Interface Coating and Nitride Enhancing Additive on Properties of Hi Nicalon Sic Fiber Reinforced Reaction Bonded Silicon Nitride Composite written by National Aeronautics and Space Adm Nasa and published by Independently Published. This book was released on 2018-09-27 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: Strong and tough Hi-Nicalon SiC fiber reinforced reaction-bonded silicon nitride matrix composites (SiC/ RBSN) have been fabricated by the fiber lay-up approach. Commercially available uncoated and PBN, PBN/Si-rich PBN, and BN/SiC coated SiC Hi-Nicalon fiber tows were used as reinforcement. The composites contained approximately 24 vol % of aligned 14 micron diameter SiC fibers in a porous RBSN matrix. Both one- and two-dimensional composites were characterized. The effects of interface coating composition, and the nitridation enhancing additive, NiO, on the room temperature physical, tensile, and interfacial shear strength properties of SiC/RBSN matrix composites were evaluated. Results indicate that for all three coated fibers, the thickness of the coatings decreased from the outer periphery to the interior of the tows, and that from 10 to 30 percent of the fibers were not covered with the interface coating. In the uncoated regions, chemical reaction between the NiO additive and the SiC fiber occurs causing degradation of tensile properties of the composites. Among the three interface coating combinations investigated, the BN/SiC coated Hi-Nicalon SiC fiber reinforced RBSN matrix composite showed the least amount of uncoated regions and reasonably uniform interface coating thickness. The matrix cracking stress in SiC/RBSN composites was predicted using a fracture mechanics based crack bridging model. Bhatt, Ramakrishana T. and Hull, David R. and Eldridge, Jeffrey I. and Babuder, Raymond Glenn Research Center NASA/TM-2000-210211, E-12330, NAS 1.15:210211
Download or read book 57th Porcelain Enamel Institute Technical Forum Volume 16 Issue 6 written by John B. Wachtman and published by John Wiley & Sons. This book was released on 2009-09-28 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is part of the Ceramic Engineering and Science Proceeding (CESP) series. This series contains a collection of papers dealing with issues in both traditional ceramics (i.e., glass, whitewares, refractories, and porcelain enamel) and advanced ceramics. Topics covered in the area of advanced ceramic include bioceramics, nanomaterials, composites, solid oxide fuel cells, mechanical properties and structural design, advanced ceramic coatings, ceramic armor, porous ceramics, and more.
Download or read book Effects of Thermal Cycling on Thermal Expansion and Mechanical Properties of SiC Fiber reinforced Reaction bonded Si3N4 Composites written by Ramakrishna T. Bhatt and published by . This book was released on 1994 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal expansion curves for SiC fiber-reinforced reaction-bonded Si3N4 matrix composites (SiC/RBSN) and unreinforced RBSN were measured from 25 to 1400 C in nitrogen and in oxygen. The effects of fiber/matrix bonding and cycling on the thermal expansion curves and room-temperature tensile properties of unidirectional composites were determined. The measured thermal expansion curves were compared with those predicted from composite theory. Predicted thermal expansion curves parallel to the fiber direction for both bonding cases were similar to that of the weakly bonded composites, but those normal to the fiber direction for both bonding cases resulted in no net dimensional changes at room temperature, and no loss in tensile properties from the as-fabricated condition. In contrast, thermal cycling in oxygen for both composites caused volume expansion primarily due to internal oxidation of RBSN. Cyclic oxidation affected the mechanical properties of the weakly bonded SiC/RBSN composites the most, resulting in loss of strain capability beyond matrix fracture and catastrophic, brittle fracture. Increased bonding between the SiC fiber and RBSN matrix due to oxidation of the carbon-rich fiber surface coating and an altered residual stress pattern in the composite due to internal oxidation of the matrix are the main reasons for the poor mechanical performance of these composites.
Download or read book NASA Technical Memorandum written by and published by . This book was released on 1994 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1989 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Thermal Cycling on Thermal Expansion and Mechanical Properties of SiC Fiber reinforced Reaction bonded Si3N4 Composites written by Ramakrishna T. Bhatt and published by . This book was released on 1994 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal expansion curves for SiC fiber-reinforced reaction-bonded Si3N4 matrix composites (SiC/RBSN) and unreinforced RBSN were measured from 25 to 1400 C in nitrogen and in oxygen. The effects of fiber/matrix bonding and cycling on the thermal expansion curves and room-temperature tensile properties of unidirectional composites were determined. The measured thermal expansion curves were compared with those predicted from composite theory. Predicted thermal expansion curves parallel to the fiber direction for both bonding cases were similar to that of the weakly bonded composites, but those normal to the fiber direction for both bonding cases resulted in no net dimensional changes at room temperature, and no loss in tensile properties from the as-fabricated condition. In contrast, thermal cycling in oxygen for both composites caused volume expansion primarily due to internal oxidation of RBSN. Cyclic oxidation affected the mechanical properties of the weakly bonded SiC/RBSN composites the most, resulting in loss of strain capability beyond matrix fracture and catastrophic, brittle fracture. Increased bonding between the SiC fiber and RBSN matrix due to oxidation of the carbon-rich fiber surface coating and an altered residual stress pattern in the composite due to internal oxidation of the matrix are the main reasons for the poor mechanical performance of these composites.
Download or read book ASM Specialty Handbook written by Joseph R. Davis and published by ASM International. This book was released on 1997-01-01 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials covered include carbon, alloy and stainless steels; alloy cast irons; high-alloy cast steels; superalloys; titanium and titanium alloys; refractory metals and alloys; nickel-chromium and nickel-thoria alloys; structural intermetallics; structural ceramics, cermets, and cemented carbides; and carbon-composites.
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 1032 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Fiber Content on Mechanical Properties of CVD SiC Fiber Reinforced Strontium Aluminosilicate Glass Ceramic Composites written by Narottam P. Bansal and published by . This book was released on 1996 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: