Download or read book Influence of Composition and Processing on the Oxidation Behavior of MCrAlY Coatings for TBC Applications written by Juan Toscano and published by Forschungszentrum Jülich. This book was released on 2009 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zsfassung in dt. und engl. Sprache.
Download or read book Influence of Composition and Processing on the Oxidation Behavior of MCrAlY coatings for TBC Applications written by Juan Pablo Toscano Alvarez and published by . This book was released on 2008 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oxidation behaviour of MCrAlX coatings written by Pimin Zhang and published by Linköping University Electronic Press. This book was released on 2018-02-12 with total page 79 pages. Available in PDF, EPUB and Kindle. Book excerpt: MCrAlY coatings (M=Ni and/or Co) have been widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive to improve engine combustion efficiency while reducing emissions by increasing the operation temperature brings a big challenge for coating design. As a result, the need for improvement of MCrAlY coatings for better oxidation resistance is essential. Formation of a stable, dense, continuous, and slow-growing ?-Al2O3 layer, on the MCrAlY coating surface, is the key to oxidation protection, since the protective ?-Al2O3 scale offers superior oxidation resistance due to its lower oxygen-diffusion rate as compared with other oxides. The ability of a MCrAlY coating to form and maintain such a protective scale depends on the coating composition and microstructure, and can be improved through optimization of deposition parameters, modification of coating surface conditions, and so on. Part of this thesis work focuses on studying the effect of post-deposition surface treatments on the oxidation behavior of MCrAlX coatings (X can be yttrium and/or other minor alloying elements). The aim is to gain fundamental understanding of alumina scale evolution during oxidation which is important for achieving improved oxidation resistance of MCrAlX coatings. Oxide scale formed on coatings at initial oxidation stage and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and weight gain. Results showed that both mechanically polished and shot-peened coatings exhibited superior performance due to rapid formation of ?-Al2O3 fully covering the coating and suppressing growth of transient alumina, assisted by the high density of ?-Al2O3 nuclei on surface treatment induced defects. The early development of a two-layer alumina scale, consisting of an inward-grown inner ?-Al2O3 layer and an outer layer transformed from outward-grown transient alumina, resulted in a higher oxide growth rate of the as-sprayed coating. The positive effect of the surface treatments on retarding oxide scale growth and suppressing formation of spinel was also observed in oxidation test up to 1000 hrs. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form ?-Al2O3 is of great importance to accurately evaluate coating lifetime, which is the aim of the other part of the thesis work. Survey of published results on a number of binary Ni-Al and ternary Ni-Cr-Al, Ni-Al-Si systems shows that the empirical Al-concentration based criterion is inadequate to properly predict the formation of a continuous ?-Al2O3 scale. On the other hand, correlating the corresponding Al-activity data, calculated from measured chemical compositions using the Thermo-Calc software, to the experimental oxidation results has revealed a temperature dependent, critical Al-activity value for forming continuous ?-Al2O3 scale. To validate the criterion, long-term oxidation tests were performed on five MCrAlX coatings with varying compositions and the implementation of the Al-activity based criterion on these coatings successfully predicted ?-Al2O3 formation, showing a good agreement with experiment results.
Download or read book Performance of MCrAlX coatings written by Pimin Zhang and published by Linköping University Electronic Press. This book was released on 2019-11-04 with total page 61 pages. Available in PDF, EPUB and Kindle. Book excerpt: MCrAlY coatings (M=Ni and/or Co) are widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive for coating systems to bestow adequate oxidation and corrosion resistance upon the components becomes urgent as an inevitable result of the necessary improvement in engine combustion efficiency and service lifetime. Through the careful design of the composition, MCrAlY coating performance can be optimized to meet the needs under different service conditions and component materials, therefore, “MCrAlX”, with “X” stands for the minor alloying elements, is used to highlight the effect. In the present thesis, the performance of new MCrAlX coatings is investigated with respect to oxidation, hot corrosion and interactions between coating-superalloy substrates. Oxidation of MCrAlX coatings can be generally categorized into initial, steady and close-to-end stages. Coating performance can be affected by various factors at different stages, therefore, experiments were designed by targeting the oxidation stages. Investigation on the initial stage oxidation behavior of MCrAlY coatings with post-deposition surface treatments reveals the different growth mechanisms of alumina scales. Surface treatments significantly reduce the alumina growth rate by suppressing transient alumina development and aiding the early formation of ?-Al2O3, which improves the long-term oxidation performance of the coating. Similarly, the modification of minor alloy elements in MCrAlX coatings also serves the purpose. The oxidation behavior of new MCrAlX coatings was investigated at the steady oxidation stage, followed by the microstructure observation, thermodynamic and kinetic simulations. As an alternative reactive element addition of Y, Ce shows a negative effect on the formation of columnar alumina scales of high strain tolerance. In comparison, Fe or Ru addition shows no influence on alumina growth, rather than strengthening the phase stability in the coating and reducing the interdiffusion between coating-substrate through different mechanisms. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form ?-Al2O3 is of great importance to accurately evaluate coating lifetime. A temperature-dependent critical Al-activity criterion was proposed to better predict the formation of a continuous ?-Al2O3 scale based on correction of elemental activity using thermodynamic database to replace the empirical Al-concentration based criterion. Severe interdiffusion occurs between coating-substrate during high temperature oxidation, accelerating the degradation of the system. Interdiffusion behavior of diffusion couples of superalloys-MCrAlX coatings were examined. It is highlighted that the recrystallization of superficial layer of the substrate contributes to the secondary reaction zone formation and element interdiffusion controls subsequent zone thickening. Study on Type I hot corrosion behavior of new MCrAlX coatings shows that the addition of Fe has no influence on basic fluxing reactions before severe Al depletion from the coating occurs. Instead, it boosts the “effective” Al supply of coating by shifting the equilibrium concentration of Al in the ? phase to a low Al level. Besides, the pre-mature coating degradation at the coating-substrate interface was due to the fast growth of corrosion products from substrate induced large local volume expansions, resulting in early coating spallation. MCrAlY ytbeläggningar (M=Ni och/eller Co) används ofta för att skydda komponenter tillverkade av superlegeringar mot oxidation samt högtemperaturskorrosion i de heta gasturbindelarna. Förbättrad förbränningseffektivitet och livslängd hos gasturbiner, gör att ytbeläggningssystemen måste besitta adekvata oxidations- och korrosionsmotstånd. Genom att omsorgsfullt utforma den kemiska sammansättningen hos MCrAlY ytbeläggningar kan deras prestanda optimeras för att möta kraven från olika driftförhållanden samt olika substratmaterial, därför används beteckningen "MCrAlX" för att belysa förändringar av den kemiska kompositionen, där "X" står för reaktiva legeringsämnen som tillsätts i mindre mängder. I denna avhandling undersöks prestandan hos en ny MCrAlX ytbeläggning med hänsyn till oxidation, högtemperaturskorrosion och interaktionen mellan ytbeläggningen och superlegeringssubstratet. Oxidation av MCrAlX ytbeläggningar kan generellt kategoriseras i tre faser; initiala, stabila och nära-slutet fasen. Ytbeläggningens prestanda kan påverkas av olika faktorer vid de olika faserna, därför utformades olika experiment för att undersöka de olika oxidationsfaserna. Undersökningen av den initiala fasen av oxidationsbeteendet hos MCrAlX ytbeläggningar som genomgått ytbehandlingar efter ytbeläggningsdeponeringen avslöjade olika tillväxtmekanismer hos aluminiumoxidskikten. Aluminiumoxidens tillväxthastighet reducerades signifikant av ytbehandlingarna, detta genom att undertrycka utvecklingen av övergående aluminiumoxid och bistå den tidiga tillväxten av ?-Al2O3, vilket förbättrar ytbeläggningens oxidationsprestanda långsiktigt. De reaktiva legeringsämnena som tillsätts i mindre mänger påverkar ytbeläggningens oxidationsprestanda på liknande sätt. Oxidationsbeteendet hos de nya MCrAlX ytbeläggningarna i den stabila fasen följdes av mikrostrukturundersökning, termodynamiska och kinetiska simuleringar. Det framkom att Ce visar en negativ effekt på bildandet av kolumnära aluminiumoxidskikt med hög töjningstolerans som alternativt reaktivt legeringsämne till Y. Jämförelsevis ger Fe- eller Ru-tillsatser ingen påverkan på aluminiumoxidtillväxten, förutom att det förstärker fasstabiliteten i ytbeläggningen samt genom olika mekanismer reducerar interdiffusionen mellan ytbeläggningen och substratet. När oxidationsprocessen kommit till nära-slutet fasen, är det viktigt att uppskatta kapaciteten hos en ytbeläggning att bilda ?-Al2O3, detta då det är ett tillförlitligt kriterium för att noggrant kunna utvärdera ytbeläggningens livslängd. Därför föreslogs ett temperaturberoende kriterium för kritisk Al-aktivitet för att bättre kunna förutsäga bildandet av ett kontinuerligt ?-Al2O3-skikt. Kriteriet baserades på korrigering av legeringsämnens aktivitet genom att använda en termodynamisk databas, detta för att ersätta det empiriska Al-koncentrations baserade kriteriet. Vid högtemperatursoxidation sker en omfattande interdiffusion mellan ytbeläggningen och substratet, vilket accelererar degraderingen av ytbeläggningssystemet. Därför har interdiffusionsbeteendet mellan superlegeringssubstratet och MCrAlX ytbeläggningen undersökts i denna avhandling. Det framkom att rekristallisationen av ytliga skikt av substratet bidrar till formationen av den sekundära reaktionszonen och att interdiffusion kontrollerar zonens efterföljande tjocklektillväxt. Undersökningen av Typ I högtemperaturskorrosionsbeteendet hos en ny MCrAlX ytbeläggning visar att legeringstillägg av Fe inte påverkar de grundläggande flödesreaktionerna innan en kritisk Al utarmning sker i ytbeläggningen. Istället stimulerar det tillförseln av Al genom att skifta jämviktskoncentrationen av Al i ? fasen till en låg nivå av Al. Det framkom också att den tidiga degraderingen av ytbeläggningen vid gränsskiktet mellan ytbeläggningen och substratet kommer av att den snabba tillväxten av korrosionsprodukter från substratet inducerade en stor lokal volymsutvidgning, vilket ledde till tidig ytbeläggningsspallation.
Download or read book Influence of Material and Testing Parameters on the Lifetime of TBC Systems with MCrAlY and NiPtAl Bondcoats written by Peng Song and published by Forschungszentrum Jülich. This book was released on 2012 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Influence of the Dynamic Ergodic Divertor on the Radial Electric Field at the Tokamak TEXTOR written by Jan Willem Coenen and published by Forschungszentrum Jülich. This book was released on 2009 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Amorphous and Microcrystalline Silicon Applied in Very Thin Tandem Solar Cells written by Sandra Schicho and published by Forschungszentrum Jülich. This book was released on 2011 with total page 219 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Ceramic Coatings for High Temperature Environments written by Amirhossein Pakseresht and published by Springer Nature. This book was released on 2024-01-06 with total page 493 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses the recent trends in thermal and environmental barrier coatings and their applications in extreme environments. It introduces the state of the art in coating materials and processes for high and ultrahigh-temperature environments and identifies areas for improvement in materials selection, performance upgrades, design considerations, and manufacturing methods. This book also covers fundamental studies involving modelling, creating coating architectures, coating preparation methods, and coating capability throughout a wide temperature range. The book examines a variety of high-temperature coatings prepared through various synthesis processes such as thermal spraying, electron beam evaporation, and sol–gel methods. This book also covers ultrahigh-temperature ceramic (UHTC) materials and provides a brief overview of the synthesis method, densification processes, and coating methods along with the properties and applications of emerging high entropy UHTCs. With contributions from international researchers active in the field, this edited book features the most recent and up-to-date literature references for a broad readership consisting of academic and industrial professionals. It is suitable for graduate students as well as materials scientists and engineers working in the area of high and ultrahigh-temperature ceramic materials.
Download or read book Thermal Barrier Coatings written by Hongbo Guo and published by Woodhead Publishing. This book was released on 2023-01-18 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal Barrier Coatings, Second Edition plays a critical role in counteracting the effects of corrosion and degradation of exposed materials in high-temperature environments such as gas turbine and aero-engines. This updated edition reviews recent advances in the processing and performance of thermal barrier coatings, as well as their failure mechanisms. Novel technologies for the manufacturing of thermal barrier coatings (TBCs) such as plasma spray-physical vapor deposition and suspension plasma spray, are covered, as well as severe degradation of TBCs caused by CMAS attack. In addition to discussions of new materials and technologies, an outlook about next generation TBCs, including T/EBCs is discussed.This edition will provide the fundamental science and engineering of thermal barrier coatings for researchers in the field of TBCs, as well as students looking for a tutorial. Includes coverage of emerging materials, such as rare-earth doped ceramics Presents the latest on plasma spray-physical vapor deposition and suspension (solution precursor) Discusses the degradation of TBCs caused by CMAS attack and its protection Looks at thermally environmental barrier coatings, interdiffusion and diffusion barrier
Download or read book Development of Thermal Spray Processes with Liquid Feedstocks written by Alexandre Guignard and published by Forschungszentrum Jülich. This book was released on 2012 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Impact of Different Vertical Transport Representations on Simulating Processes in the Tropical Tropopause Layer TTL written by Felix Plöger and published by Forschungszentrum Jülich. This book was released on 2011 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experiments and Numerical Studies on Transport of Sulfadiazine in Soil Columns written by Myriam Unold and published by Forschungszentrum Jülich. This book was released on 2010 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Development of Thin Film Inorganic Membranes for Oxygen Separation written by Hyo Jeong Moon and published by Forschungszentrum Jülich. This book was released on 2012 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Non invasive Monitoring of Water and Solute Fluxes in a Cropped Soil written by Sarah Garré and published by Forschungszentrum Jülich. This book was released on 2010 with total page 175 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electron Transport in the Plasma Edge with Rotating Resonant Magnetic Perturbations at the TEXTOR Tokamak written by Henning Stoschus and published by Forschungszentrum Jülich. This book was released on 2011 with total page 141 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Processes in the Yangtze River System written by Stephan Küppers and published by Forschungszentrum Jülich. This book was released on 2011 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Disposal Strategy of Proton Irradiated Mercury from High Power Spallation Sources written by Suresh Chiriki and published by Forschungszentrum Jülich. This book was released on 2010 with total page 151 pages. Available in PDF, EPUB and Kindle. Book excerpt:
