Download or read book In situ Small Angle X ray Scattering Investigation of Transient Nanostructure of Multi phase Polymer Materials Under Mechanical Deformation written by Ahmad Zeinolebadi and published by Springer Science & Business Media. This book was released on 2013-01-30 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results in this dissertation set the ground to answer a fundamental question in data-driven polymer material science: "Why don't prepared composites show less fatigue than the pure plastics?" A simultaneous analysis of mechanical testing and small angle X-Ray scattering from the DESY source in Hamburg has been applied to approach this question, which is also central to the European research project "Nanotough", and the results are clearly presented in this book. The evolution of the materials structure is visualized and quantitatively analyzed from exhaustive sequences of scattering images. Three different classes of polymer composites are presented as typical and illustrative examples. The obtained results illustrate that the interactions of their components can cause unpredictable structural effects, ultimaltely leading to a weakening of the material, where a reinforcement was expected.
Download or read book In situ Materials Characterization written by Alexander Ziegler and published by Springer Science & Business Media. This book was released on 2014-04-01 with total page 265 pages. Available in PDF, EPUB and Kindle. Book excerpt: The behavior of nanoscale materials can change rapidly with time either because the environment changes rapidly or because the influence of the environment propagates quickly across the intrinsically small dimensions of nanoscale materials. Extremely fast time resolution studies using X-rays, electrons and neutrons are of very high interest to many researchers and is a fast-evolving and interesting field for the study of dynamic processes. Therefore, in situ structural characterization and measurements of structure-property relationships covering several decades of length and time scales (from atoms to millimeters and femtoseconds to hours) with high spatial and temporal resolutions are crucially important to understand the synthesis and behavior of multidimensional materials. The techniques described in this book will permit access to the real-time dynamics of materials, surface processes and chemical and biological reactions at various time scales. This book provides an interdisciplinary reference for research using in situ techniques to capture the real-time structural and property responses of materials to surrounding fields using electron, optical and x-ray microscopies (e.g. scanning, transmission and low-energy electron microscopy and scanning probe microscopy) or in the scattering realm with x-ray, neutron and electron diffraction.
Download or read book Soft Matter Characterization written by Redouane Borsali and published by Springer Science & Business Media. This book was released on 2008-07-28 with total page 1490 pages. Available in PDF, EPUB and Kindle. Book excerpt: This 2-volume set includes extensive discussions of scattering techniques (light, neutron and X-ray) and related fluctuation and grating techniques that are at the forefront of this field. Most of the scattering techniques are Fourier space techniques. Recent advances have seen the development of powerful direct imaging methods such as atomic force microscopy and scanning probe microscopy. In addition, techniques that can be used to manipulate soft matter on the nanometer scale are also in rapid development. These include the scanning probe microscopy technique mentioned above as well as optical and magnetic tweezers.
Download or read book Advanced Mechanical Properties and Deformation Mechanisms of Bulk Nanostructured Materials written by and published by . This book was released on 2011 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bulk nanostructured (NS) materials have emerged as a new class of materials having unusual structures and properties. As a result, they have attracted considerable attention in recent years. Bulk NS materials are single or multi-phase polycrystals with a nanoscale grain size and can usually be classified into nanocrystalline (
Download or read book Magnetic Small Angle Neutron Scattering written by Andreas Michels and published by Oxford University Press. This book was released on 2021 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnetic Small-Angle Neutron Scattering provides the first extensive treatment of magnetic small-angle neutron scattering (SANS). The theoretical background required to compute magnetic SANS cross sections and correlation functions related to long-wavelength magnetization structures is laidout. The concepts are scrutinized based on the discussion of experimental neutron data. Regarding prior background knowledge, some familiarity with the basic magnetic interactions and phenomena as well as scattering theory is desired.Besides exposing the different origins of magnetic SANS, and furnishing the basics of the magnetic SANS technique in early chapters, a large part of the book is devoted to a comprehensive treatment of the continuum theory of micromagnetics, as it is relevant for the study of the elastic magneticSANS cross section. Analytical expressions for the magnetization Fourier components allow to highlight the essential features of magnetic SANS and to analyze experimental data both in reciprocal, as well as in real space. Later chapters provide an overview on the magnetic SANS of nanoparticles andso-called complex systems (e.g., ferrofluids, magnetic steels, spin glasses and amorphous magnets). It is this subfield where major progress is expected to be made in the coming years, mainly via the increased usage of numerical micromagnetic simulations (Chapter 7), which is a very promisingapproach for the understanding of the magnetic SANS from systems exhibiting nanoscale spin inhomogeneity.
Download or read book Polymer Morphology written by Qipeng Guo and published by John Wiley & Sons. This book was released on 2016-05-16 with total page 472 pages. Available in PDF, EPUB and Kindle. Book excerpt: With a focus on structure-property relationships, this book describes how polymer morphology affects properties and how scientists can modify them. The book covers structure development, theory, simulation, and processing; and discusses a broad range of techniques and methods. • Provides an up-to-date, comprehensive introduction to the principles and practices of polymer morphology • Illustrates major structure types, such as semicrystalline morphology, surface-induced polymer crystallization, phase separation, self-assembly, deformation, and surface topography • Covers a variety of polymers, such as homopolymers, block copolymers, polymer thin films, polymer blends, and polymer nanocomposites • Discusses a broad range of advanced and novel techniques and methods, like x-ray diffraction, thermal analysis, and electron microscopy and their applications in the morphology of polymer materials
Download or read book Nanostructure Science and Technology written by Richard W. Siegel and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Timely information on scientific and engineering developments occurring in laboratories around the world provides critical input to maintaining the economic and technological strength of the United States. Moreover, sharing this information quickly with other countries can greatly enhance the productivity of scientists and engineers. These are some of the reasons why the National Science Foundation (NSF) has been involved in funding science and technology assessments comparing the United States and foreign countries since the early 1980s. A substantial number of these studies have been conducted by the World Technology Evaluation Center (WTEC) managed by Loyola College through a cooperative agreement with NSF. The National Science and Technology Council (NSTC), Committee on Technology's Interagency Working Group on NanoScience, Engineering and Technology (CT/IWGN) worked with WTEC to develop the scope of this Nanostucture Science and Technology report in an effort to develop a baseline of understanding for how to strategically make Federal nanoscale R&D investments in the coming years. The purpose of the NSTC/WTEC activity is to assess R&D efforts in other countries in specific areas of technology, to compare these efforts and their results to U. S. research in the same areas, and to identify opportunities for international collaboration in precompetitive research. Many U. S. organizations support substantial data gathering and analysis efforts focusing on nations such as Japan. But often the results of these studies are not widely available. At the same time, government and privately sponsored studies that are in the public domain tend to be "input" studies.
Download or read book Direct Analysis of Diffraction by Matter written by Rolf Hosemann and published by . This book was released on 1962 with total page 764 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Characterization of Polymer Blends written by Sabu Thomas and published by John Wiley & Sons. This book was released on 2015-02-09 with total page 972 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filling the gap for a reference dedicated to the characterization of polymer blends and their micro and nano morphologies, this book provides comprehensive, systematic coverage in a one-stop, two-volume resource for all those working in the field. Leading researchers from industry and academia, as well as from government and private research institutions around the world summarize recent technical advances in chapters devoted to their individual contributions. In so doing, they examine a wide range of modern characterization techniques, from microscopy and spectroscopy to diffraction, thermal analysis, rheology, mechanical measurements and chromatography. These methods are compared with each other to assist in determining the best solution for both fundamental and applied problems, paying attention to the characterization of nanoscale miscibility and interfaces, both in blends involving copolymers and in immiscible blends. The thermodynamics, miscibility, phase separation, morphology and interfaces in polymer blends are also discussed in light of new insights involving the nanoscopic scale. Finally, the authors detail the processing-morphology-property relationships of polymer blends, as well as the influence of processing on the generation of micro and nano morphologies, and the dependence of these morphologies on the properties of blends. Hot topics such as compatibilization through nanoparticles, miscibility of new biopolymers and nanoscale investigations of interfaces in blends are also addressed. With its application-oriented approach, handpicked selection of topics and expert contributors, this is an outstanding survey for anyone involved in the field of polymer blends for advanced technologies.
Download or read book Polyurethane Elastomers written by Cristina Prisacariu and published by Springer Science & Business Media. This book was released on 2011-07-03 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive account of the physical / mechanical behaviour of polyurethanes (PU ́s) elastomers, films and blends of variable crystallinity. Aspects covered include the elasticity and inelasticity of amorphous to crystalline PUs, in relation to their sensitivity to chemical and physical structure. A study is made of how aspects of the constitutive responses of PUs vary with composition: the polyaddition procedure, the hard segment, soft segment and chain extender (diols and diamines) are varied systematically in a large number of systems of model and novel crosslinked andthermoplastic PUs. Results will be related to: microstructural changes, on the basis of evidence from x-ray scattering (SAXS and WAXS), and also dynamic mechanical analyses (DMA), differential scanning calorimetry (DSC) and IR dichroism. Inelastic effects will be investigated also by including quantitative correlations between the magnitude of the Mullins effect and the fractional energy dissipation by hysteresis under cyclic straining, giving common relations approached by all the materials studied. A major structural feature explored is the relationship between the nature of the hard segment (crystallising or not) and that of the soft segments. Crystallinity has been sometimes observed in the commercial PUs hard phase but this is usually limited to only a few percent for most hard segment structures when solidified from the melt. One particular diisocyanate, 4,4’-dibenzyl diisocyanate (DBDI) that, in the presence of suitable chain extenders ( diols or diamines), gives rise to significant degrees of crystallinity [i-iii] and this is included in the present work. Understanding the reaction pathways involved, in resolving the subtle morphological evolution at the nanometre level, and capturing mathematically the complex, large-deformation nonlinear viscoelastic mechanical behaviour are assumed to bring new important insights in the world basic research in polyurethanes and towards applied industrial research in this area.
Download or read book Rheology of Complex Fluids written by Abhijit P. Deshpande and published by Springer Science & Business Media. This book was released on 2010-09-20 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of the School on Rheology of Complex fluids is to bring together young researchers and teachers from educational and R&D institutions, and expose them to the basic concepts and research techniques used in the study of rheological behavior of complex fluids. The lectures will be delivered by well-recognized experts. The book contents will be based on the lecture notes of the school.
Download or read book Materials Science and Engineering Laboratory written by and published by . This book was released on 1993 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Residual Stresses 2018 written by Marc Seefeldt and published by Materials Research Forum LLC. This book was released on 2018-10-10 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: The European Conference on Residual Stresses (ECRS) series is the leading European forum for scientific exchange on internal and residual stresses in materials. It addresses both academic and industrial experts and covers a broad gamut of stress-related topics from instrumentation via experimental and modelling methodology up to stress problems in specific processes such as welding or shot-peening, and their impact on materials properties. Chapters: Diffraction Methods; Mechanical Relaxation Methods; Acoustic and Electromagnetic Methods; Composites, Nano and Microstructures; Films, Coatings and Oxides; Cold Working and Machining; Heat Treatments and Phase Transformations; Welding, Fatigue and Fracture: Stresses in Additive Manufacturing.
Download or read book Polymer Colloids written by Rodney Priestley and published by Royal Society of Chemistry. This book was released on 2019-12-02 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Academic and industrial research around polymer-based colloids is huge, driven both by the development of mature technologies, e.g. latexes for coatings, as well as the advancement of new materials and applications, such as building blocks for 2D/3D structures and medicine. Edited by two world-renowned leaders in polymer science and engineering, this is a fundamental text for the field. Based on a specialised course by the editors, this book provides the reader with an invaluable single source of reference. The first section describes formation, explaining basic properties of emulsions and dispersion polymerization, microfluidic approaches to produce polymer-based colloids and formation via directed self-assembly. The next section details characterisation methodologies from microscopy and small angle scattering, to surface science and simulations. The final chapters close with applications, including Pickering emulsions and molecular engineering for materials development. A comprehensive guide to polymer colloids, with contributions by leaders in their respective areas, this book is a must-have for researchers and practitioners working across polymers, soft matter and chemical and molecular engineering.
Download or read book Micellar Solutions and Microemulsions written by Sow Hsin Chen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: During the last decade there has been a renewed interest in research on supramolecular assemblies in solutions, such as micelles and microemulsions, not only because of their extensive applications in industries dealing with catalysts, detergency, biotechnology, and enhanced oil recovery, but also due to the development of new and more powerful experimental and theoretical tools for probing the microscopic behavior of these systems. Prominent among the array of the newly available experimental techniques are photon correlation spectroscopy, small-angle neutron and X-ray scattering, and neutron spin-echo and nuclear magnetic resonance spectroscopies. On the theoretical side, the traditionally emphasized thermodynamic approach to the study of the phase behavior of self-assembled systems in solutions is gradually being replaced by statistical mechanical studies of semi-micro scopic and microscopic models of the assemblies. Since the statistical mechanical approach demands as its starting point the microscopic struc tural information of the self-assembled system, the experimental determina tion of the structures of micelles and microemulsions becomes of paramount interest. In this regard the scattering techniques mentioned above have played an important role in recent years and will continue to do so in the future. In applying the scattering techniques to the supramolecular species in solution, one cannot often regard the solution to be ideal. This is because the inter-aggregate interaction is often long-ranged since it is coulombic in nature and the interparticle correlations are thus appreciable.
Download or read book Materials Design Inspired by Nature written by Peter Fratzl and published by Royal Society of Chemistry. This book was released on 2015-11-09 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt: The inner architecture of a material can have an astonishing effect on its overall properties and is vital to understand when designing new materials. Nature is a master at designing hierarchical structures and so researchers are looking at biological examples for inspiration, specifically to understand how nature arranges the inner architectures for a particular function in order to apply these design principles into man-made materials. Materials Design Inspired by Nature is the first book to address the relationship between the inner architecture of natural materials and their physical properties for materials design. The book explores examples from plants, the marine world, arthropods and bacteria, where the inner architecture is exploited to obtain specific mechanical, optical or magnetic properties along with how these design principles are used in man-made products. Details of the experimental methods used to investigate hierarchical structures are also given. Written by leading experts in bio-inspired materials research, this is essential reading for anyone developing new materials.
Download or read book Liquid Cell Electron Microscopy written by Frances M. Ross and published by Cambridge University Press. This book was released on 2017 with total page 529 pages. Available in PDF, EPUB and Kindle. Book excerpt: 2.6.2 Electrodes for Electrochemistry
