Download or read book Implications of Low Particulate Matter Emissions on System Fuel Efficiency for High Efficiency Clean Combustion written by and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced diesel combustion regimes such as High Efficiency Clean Combustion (HECC) offer the benefits of reduced engine out NOX and particulate matter (PM) emissions. Lower PM emissions during advanced combustion reduce the demand on diesel particulate filters (DPFs) and can, thereby, reduce the fuel penalty associated with DPF regeneration. In this study, a SiC DPF was loaded and regenerated on a 1.7-liter 4-cylinder diesel engine operated in conventional and advanced combustion modes at different speed and load conditions. A diesel oxidation catalyst (DOC) and a lean NOX trap (LNT) were also installed in the exhaust stream. Five steady-state speed and load conditions were weighted to estimate Federal Test Procedure (FTP) fuel efficiency. The DPF was loaded using lean-rich cycling with frequencies that resulted in similar levels of NOX emissions downstream of the LNT. The pressure drop across the DPF was measured at a standard point (1500 rpm, 5.0 bar) before and after loading, and a P rise rate was determined for comparison between conventional and advanced combustion modes. Higher PM emissions in conventional combustion resulted in a higher rate of backpressure rise across the DPF at all of the load points leading to more frequent DPF regenerations and higher fuel penalty. The fuel penalty during conventional combustion was 4.2% compared with 3.1% for a mixture of conventional and advanced modes.
Download or read book Medium and Heavy Duty Fuel Efficiency Improvement Program written by and published by . This book was released on 2011 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Reducing Particulate Emissions in Gasoline Engines written by Thorsten Boger and published by SAE International. This book was released on 2018-11-28 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: For years, diesel engines have been the focus of particulate matter emission reductions. Now, however, modern diesel engines emit less particles than a comparable gasoline engine. This transformation necessitates an introduction of particulate reduction strategies for the gasoline-powered vehicle. Many strategies can be leveraged from diesel engines, but new combustion and engine control technologies will be needed to meet the latest gasoline regulations across the globe. Particulate reduction is a critical health concern in addition to the regulatory requirements. This is a vital issue with real-world implications. Reducing Particulate Emissions in Gasoline Engines encompasses the current strategies and technologies used to reduce particulates to meet regulatory requirements and curtail health hazards - reviewing principles and applications of these techniques. Highlights and features in the book include: Gasoline particulate filter design, function and applications Coated and uncoated three way catalyst design and integration Measurement of gasoline particulate matter emission, both laboratory and PEMS The goal is to provide a comprehensive assessment of gasoline particulate emission control to meet regulatory and health requirements - appealing to calibration, development and testing engineers alike.
Download or read book The Ongoing Challenge of Managing Carbon Monoxide Pollution in Fairbanks Alaska written by National Research Council and published by National Academies Press. This book was released on 2002-08-22 with total page 158 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon monoxide (CO) is a toxic air pollutant produced largely from vehicle emissions. Breathing CO at high concentrations leads to reduced oxygen transport by hemoglobin, which has health effects that include impaired reaction timing, headaches, lightheadedness, nausea, vomiting, weakness, clouding of consciousness, coma, and, at high enough concentrations and long enough exposure, death. In recognition of those health effects, the U.S. Environmental Protection Agency (EPA), as directed by the Clean Air Act, established the health-based National Ambient Air Quality Standards (NAAQS) for CO in 1971. Most areas that were previously designated as "nonattainment" areas have come into compliance with the NAAQS for CO, but some locations still have difficulty in attaining the CO standards. Those locations tend to have topographical or meteorological characteristics that exacerbate pollution. In view of the challenges posed for some areas to attain compliance with the NAAQS for CO, congress asked the National Research Council to investigate the problem of CO in areas with meteorological and topographical problems. This interim report deals specifically with Fairbanks, Alaska. Fairbanks was chosen as a case study because its meteorological and topographical characteristics make it susceptible to severe winter inversions that trap CO and other pollutants at ground level.
Download or read book Cost Effectiveness and Deployment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2015-09-28 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt: The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.
Download or read book Proceedings of the FISITA 2012 World Automotive Congress written by SAE-China and published by Springer Science & Business Media. This book was released on 2012-11-02 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the FISITA 2012 World Automotive Congress are selected from nearly 2,000 papers submitted to the 34th FISITA World Automotive Congress, which is held by Society of Automotive Engineers of China (SAE-China ) and the International Federation of Automotive Engineering Societies (FISITA). This proceedings focus on solutions for sustainable mobility in all areas of passenger car, truck and bus transportation. Volume 2: Advanced Internal Combustion Engines (II) focuses on: •Flow and Combustion Diagnosis •Engine Design and Simulation •Heat Transfer and Waste Heat Reutilization •Emission Standard and International Regulations Above all researchers, professional engineers and graduates in fields of automotive engineering, mechanical engineering and electronic engineering will benefit from this book. SAE-China is a national academic organization composed of enterprises and professionals who focus on research, design and education in the fields of automotive and related industries. FISITA is the umbrella organization for the national automotive societies in 37 countries around the world. It was founded in Paris in 1948 with the purpose of bringing engineers from around the world together in a spirit of cooperation to share ideas and advance the technological development of the automobile.
Download or read book Particulate Matter Emissions from a Direct Injection Spark Ignition Engine Under Cold fast idle Conditions for Ethanol gasoline Blends written by Iason Dimou and published by . This book was released on 2011 with total page 83 pages. Available in PDF, EPUB and Kindle. Book excerpt: In an effort to build internal combustion engines with both reduced brake-specific fuel consumption and better emission control, engineers developed the Direct Injection Spark Ignition (DISI) engine. DISI engines combine the specific higher output of the spark ignition engine, with the better efficiency of the compression ignition engine at part load. Despite their benefits, DISI engines still suffer from high hydrocarbon, NO2 and particulate matter (PM) emissions. Until recently, PM emissions have received relatively little attention, despite their severe effects on human health, related mostly to their size. Previous research indicates that almost 80% of the PM is emitted during the first few minutes of the engine's operation (cold-start-fast-idling period). A proposed solution for PM emission reduction is the use of fuel blends with ethanol. The present research experimentally measures the effect of ethanol content in fuel on PM formation in the combustion chamber of a DISI engine during the cold-start period. A novel sampling system has been designed and combined with a Scanning Mobility Particle Sizer (SMPS) system, in order to measure the particulate matter number (PN) concentration 15 cm downstream from the exhaust valves of a DISI engine, for a temperature range between 0 and 40"C, under low load operation. Seven gasohol fuels have been tested with the ethanol content varying from 0% (EO) up to 85% (E85). For E10 to E85, PN modestly increases when the engine coolant temperature (ECT) is lowered. The PN distributions, however, are insensitive to the ethanol content of the fuel. The total PN for EQ is substantially higher than for the gasohol fuels, at ECT below 20'C. However, for ECT higher than 20'C, the total PN values (obtained from integrating the PN distribution from 15 to 350 nm) are approximately the same for all fuels. This sharp change in PN from EQ to E10 is confirmed by running the tests with E2.5 and E5; the midpoint of the transition occurs at approximately E5. Because the fuels' evaporating properties do not change substantially from EQ to E10, the significant change in PN is attributed to the particulate matter formation chemistry.
Download or read book Effects of Oxygenates Blended with Diesel Fuel on Particulate Matter Emissions from a Compression ignition Engine written by Adelbert Su-Tseh Cheng and published by . This book was released on 2002 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanoparticle Emissions From Combustion Engines written by Jerzy Merkisz and published by Springer. This book was released on 2015-03-19 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on particulate matter emissions produced by vehicles with combustion engines. It describes the physicochemical properties of the particulate matter, the mechanisms of its formation and its environmental impacts (including those on human beings). It discusses methods for measuring particulate mass and number, including the state-of-the-art in Portable Emission Measurement System (PEMS) equipment for measuring the exhaust emissions of both light and heavy-duty vehicles and buses under actual operating conditions. The book presents the authors’ latest investigations into the relations between particulate emission (mass and number) and engine operating parameters, as well as their new findings obtained through road tests performed on various types of vehicles, including those using diesel particulate filter regeneration. The book, which addresses the needs of academics and professionals alike, also discusses relevant European regulations on particulate emissions and highlights selected methods aimed at the reduction of particulate emissions from automobiles.
Download or read book WHO Guidelines for Indoor Air Quality written by World Health Organization and published by World Health Organization. This book was released on 2014 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Built on existing WHO indoor air quality guidelines for specific pollutants, these guidelines bring together the most recent evidence on fuel use, emission and exposure levels, health risks, intervention impacts and policy considerations, to provide practical recommendations to reduce this health burden.
Download or read book Technologies and Approaches to Reducing the Fuel Consumption of Medium and Heavy Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2010-07-30 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: Technologies and Approaches to Reducing the Fuel Consumption of Medium- and Heavy-Duty Vehicles evaluates various technologies and methods that could improve the fuel economy of medium- and heavy-duty vehicles, such as tractor-trailers, transit buses, and work trucks. The book also recommends approaches that federal agencies could use to regulate these vehicles' fuel consumption. Currently there are no fuel consumption standards for such vehicles, which account for about 26 percent of the transportation fuel used in the U.S. The miles-per-gallon measure used to regulate the fuel economy of passenger cars. is not appropriate for medium- and heavy-duty vehicles, which are designed above all to carry loads efficiently. Instead, any regulation of medium- and heavy-duty vehicles should use a metric that reflects the efficiency with which a vehicle moves goods or passengers, such as gallons per ton-mile, a unit that reflects the amount of fuel a vehicle would use to carry a ton of goods one mile. This is called load-specific fuel consumption (LSFC). The book estimates the improvements that various technologies could achieve over the next decade in seven vehicle types. For example, using advanced diesel engines in tractor-trailers could lower their fuel consumption by up to 20 percent by 2020, and improved aerodynamics could yield an 11 percent reduction. Hybrid powertrains could lower the fuel consumption of vehicles that stop frequently, such as garbage trucks and transit buses, by as much 35 percent in the same time frame.
Download or read book Nitrogen oxides NOx why and how they are controlled written by and published by DIANE Publishing. This book was released on 1999 with total page 57 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effects of Secondary Air Injection on Particulate Matter Emissions written by Joseph James Pritchard and published by . This book was released on 2014 with total page 71 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study was performed to investigate the effects of secondary air injection (SAI) on particulate matter (PM) emissions. SAI was developed to reduce hydrocarbon (HC) emissions and has been shown to be effective as a strategy to reduce HC emissions at cold-start. In general, cold-start emissions have become an increasingly important problem due to new, more stringent vehicle emissions regulations. Direct-injection, spark-ignition (DISI) engines, which emit high levels of PM, are growing in popularity because of their fuel efficiency improvements. Meeting PM emissions becomes a more difficult task due to more stringent standards and the greater adoption of DISI engines. This study seeks to investigate the potential use of SAI to reduce PM emissions in the exhaust system. Engine based experiments were conducted using a 2.0 L, turbocharged, DISI General Motors LNF engine. The engine was outfitted with a secondary air injection system and several thermocouples to measure exhaust stream temperature. A TSI Model 3934 Scanning Mobility Particle Sizer (SMPS) was used to measure particle emissions at various engine operating conditions and secondary air rates. PM reductions were observed for the engine conditions and SAI flow rates that were tested. The maximum particle number reduction achieved was 80%. Particle number and particle volume reduction were observed to correlate well with exhaust enthalpy release.
Download or read book Assessment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2011-06-03 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various combinations of commercially available technologies could greatly reduce fuel consumption in passenger cars, sport-utility vehicles, minivans, and other light-duty vehicles without compromising vehicle performance or safety. Assessment of Technologies for Improving Light Duty Vehicle Fuel Economy estimates the potential fuel savings and costs to consumers of available technology combinations for three types of engines: spark-ignition gasoline, compression-ignition diesel, and hybrid. According to its estimates, adopting the full combination of improved technologies in medium and large cars and pickup trucks with spark-ignition engines could reduce fuel consumption by 29 percent at an additional cost of $2,200 to the consumer. Replacing spark-ignition engines with diesel engines and components would yield fuel savings of about 37 percent at an added cost of approximately $5,900 per vehicle, and replacing spark-ignition engines with hybrid engines and components would reduce fuel consumption by 43 percent at an increase of $6,000 per vehicle. The book focuses on fuel consumption-the amount of fuel consumed in a given driving distance-because energy savings are directly related to the amount of fuel used. In contrast, fuel economy measures how far a vehicle will travel with a gallon of fuel. Because fuel consumption data indicate money saved on fuel purchases and reductions in carbon dioxide emissions, the book finds that vehicle stickers should provide consumers with fuel consumption data in addition to fuel economy information.
Download or read book Flue Gas Desulfurization and Industrial Minerals written by M. Michael Miller and published by . This book was released on 1993 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contains 4,101 references on FGD [Flue Gas Desulfurization] ... primarily from 1982 through June 1993. Complements the "Flue Gas Desulfurization and Denitrification" bibliography published by the U.S. Dept. of Energy in Jan. 1985. References were located on the Energy, Science and Technology, Pollution Abstracts, and Environmental Bibliography databases. Primarily covers FGD and the use of industrial minerals in the desulfurization process or in by-product utilization and disposal. Emphasizes post-combustion removal of sulfur dioxide through processes such as in-duct injection and wet and dry scrubbing.
Download or read book Growth and Its Implications for the Future written by United States. Congress. House. Committee on Merchant Marine and Fisheries. Subcommittee on Fisheries and Wildlife Conservation and the Environment and published by . This book was released on 1973 with total page 820 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book N A P C A Abstract Bulletin written by United States. Environmental Protection Agency and published by . This book was released on 1971 with total page 1068 pages. Available in PDF, EPUB and Kindle. Book excerpt:
