Download or read book HYDRAULIC FLANGED TUBE PIPE AND HOSE CONNECTIONS 4 BOLT SPLIT FLANGE TYPE written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1972 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations.The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.Flanged heads shall be as specified in Fig. 3 and Table 1. Split flange clamp halves shall be as specified in Fig. 4 and Table 1. Port dimensions and spacing shall be as specified in Fig. 5 and Table 2.O-ring seals, having nominal dimensions as indicated in Table 1, are used in conjunction with these connections. They shall conform to the seals specified in SAE J120, Table on Dimensions and Tolerances.Bolts for use with these connections shall be of the sizes and lengths indicated in Table 1. They shall conform with the finished hexagon bolts specified in SAE J105. They shall be of SAE Grade 5 material or better as specified in SAE J429. Socket head cap screws of SAE Grade 5 material or better are acceptable.Lock washers, if used, shall be in accordance with the light spring lock washers specified in SAE J489, Dimensions of Light, Medium, Heavy, Extra Heavy, and Hi Collar Spring Lock Washers, and of sizes applicable to the corresponding bolts.The following general specifications supplement the dimensional data contained in Table 1 with respect to all unspecified detail.
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections Four Bolt Split Flange Type written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1993 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J518 HOSE CONNECTIONS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES. Flanged heads shall be as specified in Figure 3 and Table 1. Split flange clamp halves shall be as specified in Figure 4 and Table 1. Port dimensions and spacing shall be as specified in Figure 5 and Table 2. O-ring seals, having nominal dimensions as indicated in Table 1, are used in conjunction with these connections. They shall conform to the seals specified in SAE J120, Table on Dimensions and Tolerances. Bolts for use with these connections shall be of the sizes and lengths indicated in Table 1. They shall be of SAE Grade 5 material or better as specified in SAE J429. Socket head cap screws of SAE Grade 5 material or better are acceptable. Lock washers, if used, shall be in accordance with the light spring lock washers specified in SAE J489. Dimensions of Light, medium, Heavy, Extra Heavy, and Hi collar spring Lock Washers, and or sizes applicable to the corresponding bolts.
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections 4 bolt Split Flange Type written by Society of Automotive Engineers and published by . This book was released on 1968 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections 4 Screw Flange Connection Part 1 3 5 MPa to 35 MPa Code 61 written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for the Code 61 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC & FCM), and split flange clamps (FCS & FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also, included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design.The flange heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values.The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail. Parts manufactured to this standard are interchangeable with ISO 6162-1 and connectors to either standard can be supplied. Numerous changes have occurred in the industry since this standard was last updated. ISO 6162 was adopted and it added metric bolts. Over the years, SAE J518 has gone from hard inch to inch (metric referenced) and with this revision metric. The metric dimensions needed to be fine-tuned to eliminate conversion errors. The metric numbers in the SAE standard were reference numbers in the old document that moved the acceptance range by as much as 30% of the tolerance when compared to the inch numbers. At the same time, the standard is to be harmonized with the current ISO 6162-1 with the intent of incorporating the changes into an ISO 6162-1 proposed revision. To help eliminate confusion and improve the connection, a minimum of class 10.9 metric (SAE grade 8 or better) screws are now required. This revision corrects the numbers, corrects problems with the O-ring groove, increases the radius between the d8 and d9 flange head dimension, uses a common clearance hole for inch and metric bolts, adds burst pressure and other requirements, changes & recommends a washer, and numerous other changes from the 1993 revision. The pad spacing has also been changed to recognize that it could be a cavity as well as a raised or flat surface.
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections 4 bolt Split Flange Type written by Society of Automotive Engineers and published by . This book was released on 1988 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections 4 Screw Flange Connection Part 2 42 MPa Code 62 written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design.The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values.THE FOLLOWING GENERAL SPECIFICATIONS SUPPLEMENT THE DIMENSIONAL DATA CONTAINED IN THE TABLES WITH RESPECT TO ALL UNSPECIFIED DETAIL. PARTS MANUFACTURED TO THIS STANDARD ARE INTERCHANGEABLE WITH ISO 6162-2 AND CONNECTORS TO EITHER STANDARD CAN BE SUPPLIED WITH THE EXCEPTION OF THE -40 AND -48 TYPE 2 CONNECTIONS THAT ARE INCLUDED IN J518-2, BUT NOT ISO 6162-2. The DN 63 (-40) and DN 76 (-48) pad sizes existed for many years as special items in the field. Flange clamps were not available and the pads were used with pipe fittings. A couple of years ago, Italy proposed a clamp and supplied test data to support the design. The type 1 (metric screw) version has been approved at the ISO level. This SAE revision adds the -40 and -48 sizes and adds the inch screw sizes that have been used for years in the field. Finally, an identification groove was added to the flanged head. The groove had been approved many years ago, but never made it into the standard.
Download or read book Hydraulic Flange Tube Pipe and Hose Connections Four Screw Flange Connection Part 1 3 5 to 35 MPa Code 61 written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for the Code 61 metric (Type 1) and inch (Type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design.The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values.The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail. Parts manufactured to this standard are interchangeable with ISO 6162-1 and connectors to either standard can be supplied. This ballot version contains a resolution to the comments made on the last ballot. Several reference standard names have been updated, clarifications of corrosion requirements have been included, and drawing and table formatting have been changed.
Download or read book Evaluation of 4 bolt split flange connections conforming the society of Automotive Engineersstandard SAE J518c Hydraulic flanged tube pipe and host connections 4 bolt split flange type written by M. S. Fleming and published by . This book was released on 1985 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Copy of report to Dayton T. Brown from United States Coast Guard. Contains original photographs in the report.
Download or read book NBS Special Publication written by and published by . This book was released on 1971 with total page 1064 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Index of Specifications and Standards written by and published by . This book was released on 2005 with total page 782 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Index of U S Voluntary Engineering Standards written by William J. Slattery and published by . This book was released on 1971 with total page 1016 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Index of U S Voluntary Engineering Standards Supplement written by William J. Slattery and published by . This book was released on 1972 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Index of U S Voluntary Engineering Standards Supplement 1 written by William J. Slattery and published by . This book was released on 1972 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Hydraulics Pneumatics written by and published by . This book was released on 1979 with total page 1064 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Jan. 1956 issue includes Fluid power engineering index, 1931-55.
Download or read book SAE Handbook written by Society of Automotive Engineers and published by . This book was released on 1984 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Index of U S Voluntary Engineering Standards written by United States. National Bureau of Standards and published by . This book was released on 1971 with total page 1038 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Automobile Design Liability written by Richard M. Goodman and published by . This book was released on 1971 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt:
