Download or read book High Temperature Pressure Transducer Mk I written by L. H. Thacker and published by . This book was released on 1962 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book High Temperature Pressure Transducers written by Julian Delmonte and published by . This book was released on 1969 with total page 113 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Effects of Extended High temperature Storage on the Performance Characteristics of Several Strain Gage Pressure Transducers written by Randolph Williams and published by . This book was released on 1969 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication reports the results of a test program to evaluate the effects of high-temperature storage in the performance characteristics of several types of commercial strain gage pressure transducers. The results obtained indicate shifts in the zero pressure output and the sensitivity, some of which are permanent. The equipment used and the procedure followed are described.

Download or read book Hermetically Sealed High temperature Pressure Transmitter and Hermetically Sealed High temperature Liquid level Probe written by M. T. Morgan and published by . This book was released on 1955 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Design of a High Temperature Pressure Transducer written by George J. Dvorak and published by . This book was released on 1984 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book High Temperature Solid State Pressure Transducers for Military Jet Engine Environments written by Gerald L. Vick and published by . This book was released on 1973 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: The document reports the work performed to apply advance design and fabrication techniques to the economic development of high temperature solid state pressure transducers for military jet engine environments. Improvements in a previously developed high temperature solid state pressure transducer have been made in a number of areas. Media compatibility has been extended from clean air to conductive and mildly corrosive liquids and gases. Cost effective reductions to warrant production have been achieved. Accuracy has been improved by introduction of nonlinear temperature compensation. The operating temperature range has been extended from 660F to 750F with survival proven to 930F. (Author).

Download or read book High temperature Transient Pressure Transducer for Use in Liquid metal Systems written by Ted W. Nyland and published by . This book was released on 1969 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: High temperature transient pressure transducer tested for liquid metal systems.

Download or read book Transducers 01 Eurosensors XV written by Ernst Obermeier and published by Springer. This book was released on 2016-05-12 with total page 1763 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Conference is the premier international meeting for the presentation of original work addressing all aspects of the theory, design, fabrication, assembly, packaging, testing and application of solid-state sensors, actuators, MEMS, and microsystems.

Download or read book Pressure Transducer Performance and Measurement Trade Offs in a Transient High Temperature Combustion Environment written by and published by . This book was released on 1995 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: At the U.S. Army Research Laboratory (ARL), a series of tests were performed in a 120mm cannon to characterize the effects of transducer type, transducer port configuration, thermal protection media, and severe mechanical forces on the amplitude and frequency response of the pressure measurement. A ring of five pressure transducer ports (72 deg apart)) was machined 2.6 m from the rear face of a 12Omm gun trade. The physical configuration of the transducer ports consisted of three single-diameter ports with varying standoff distances, a conventional two-diameter port, and blind port. As the projectile passed the longitudinal position the pressure transducers were exposed to a transient, high temperature environment which allowed the investigators to study the fidelity of the pressure measurement under transient, high temperature, mechanically adverse gun conditions. These tests demonstrated that the use of single-diameter pressure ports with cavity depths of 0.254 mm (0.010 in) and 0.711 mm (0.028 in) win more accurately characterize the oscillatory nature of the pressure measurement than would the use of a single-diameter port with a cavity depth of 1.6O0mm (0.063 in). In addition, the combustion chamber of the weapon was also highly instrumented with pressure transducers in an attempt to evaluate the effects of various transducer types and thermal protection greases on the magnitude of the pressure measurement. This study showed that the Kistler 6211 pressure transducer (quartz) reads about 5% higher than the E30MA pressure transducer (normaline) in both the forward and rear of the chamber. No conclusion could be reached as to which gage gives the more correct quasi-steady-state pressure level.

Download or read book A Temperature Compensated Pressure Transducer for High Temperature High Pressure Applications written by Sandra Margaret Lippka and published by . This book was released on 1991 with total page 162 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Expanding the Vision of Sensor Materials written by Committee on New Sensor Technologies: Materials and Applications and published by National Academies Press. This book was released on 1995-07-06 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in materials science and engineering have paved the way for the development of new and more capable sensors. Drawing upon case studies from manufacturing and structural monitoring and involving chemical and long wave-length infrared sensors, this book suggests an approach that frames the relevant technical issues in such a way as to expedite the consideration of new and novel sensor materials. It enables a multidisciplinary approach for identifying opportunities and making realistic assessments of technical risk and could be used to guide relevant research and development in sensor technologies.

Download or read book High Temperature Pressure Transmitter Evaluation written by W. R. Miller and published by . This book was released on 1958 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Transducer Interfacing Handbook written by Analog Devices, inc and published by . This book was released on 1980 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: The tranducer as a circuit element. Interfacing considerations - bridges. Interfacing considerations - interference. Amplifiers and signal translation. Offseting and linearizing. Overall considerations. 2 interface-design examples. Thermoswitches and thermocouples. Resistance temperature detectors (RTDs). Thermistor interfacing. Semiconductor temperature transducers. Pressure-transducer interfacing. Force-transducer interfacing. Flowmeter interfacing. Interfacing level transducers. Application miscellany.

Download or read book High Temperature Thermocouples written by Harley A. Wilhelm and published by . This book was released on 1948 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book A High temperature Wideband Pressure Transducer written by Allan J. Zuckerwar and published by . This book was released on 1975 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Development of a Pressure Transducer for Usage in High temperature and Vibration Environments written by H. T. Liu and published by . This book was released on 1984 with total page 61 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of the Phase I project is to determine the feasibility of developing a highly accurate, low-range pressure transducer that is suitable for measurement in environments where high vibrations, high temperatures and varying line pressures create problems for presently available transducers. The primary sensor is an elastic metal diaphragm that forms one plate of a capacitor; the other plate is fixed with respect to the diaphragm. An electronic circuit converts the diaphragm deflections, induced by a pressure force, into voltage variations that are then sampled by a microprocessor, which is to be developed in Phase II. Because of the small oscillating mass of the diaphragm, the transducer has a high natural frequency and is largely insensitive to externally induced vibrations. The simple configuration of the capacitive transducer is potentially very large overloads with appropriate installation of an overload stop between the two plates. In comparison with other types of pressure sensors, the capacitive transducer concept offers an unusual amount of design flexibility for a wide range of operational conditions. Phase I research demonstrated the feasibility of the capacitive transducer concepts, as well as its capability to meet and potentially exceed all DoD requirements for transducer performance. (Author).

Download or read book Evaluation of a high temperature pressure transducer for use as a force transducer written by J. A. Aikin and published by . This book was released on 1983 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: