Download or read book High Power Output Operation of RCCI Combustion written by and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computational investigation of methods to extend the upper limit of power output of reactivity controlled compression ignition (RCCI) engines was performed. The study utilized two approaches. The first approach is to increase the engine speed while maintaining a medium load. The second approach is to operate at higher loads without changing the engine speed. Iso-octane and n-heptane were used to represent the low-reactivity fuel and high-reactivity fuel, respectively. A light-duty diesel engine was modeled for the high speed dual-fuel RCCI combustion study. With high-speed operation several benefits were identified. Firstly, the peak pressure rise rates (PPRR), both crank angle-based and time-based, were reduced compared to those with low-speed operation. Secondly, at high speed the NO formation residence time became short, leading to reduced NOx emissions. Lastly, a frictional penalty analysis of high-speed operation using the Chen-Flynn model was conducted, which showed only 0.5 bar FMEP increase compared to that at low-speed. These findings indicate that high-speed RCCI is a very promising path for high-power output operation. For the high-load operation study use of dual direct-injectors was explored in order to direct-inject both fuels. Analysis of the optimum injection strategy revealed two main physical mechanisms enabling high-load operation with dual direct-injectors. The first exploited local evaporative cooling from the iso-octane injection, which delayed the iso-octane ignition. The second mechanism was related to the shorter chemical residence time of the iso-octane due to its late delivery into the cylinder. It was also noted that n-heptane's role as an ignition source could not be achieved with just iso-octane. Finally, the co-axial injector location assumption was removed by using an actual dual-injector layout. Unlike results with the co-axial injector design, the actual dual-injector layout exhibited soot and CO emission problems. In order to attempt to accommodate off-center injector locations, various injector hole patterns were tested. Although these unconventional injector hole patterns improved the emissions, it is concluded that the development of a co-axial dual-fuel injector is imperative in order to achieve clean RCCI combustion at high load.

Download or read book Combustion for Power Generation and Transportation written by Avinash Kumar Agarwal and published by Springer. This book was released on 2017-01-20 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph presents both fundamental science and applied innovations on several key and emerging technologies involving fossil and alternate fuel utilization in power and transport sectors from renowned experts in the field. Some of the topics covered include: autoignition in laminar and turbulent nonpremixed flames; Langevin simulation of turbulent combustion; lean blowout (LBO) prediction through symbolic time series analysis; lasers and optical diagnostics for next generation IC engine development; exergy destruction study on small DI diesel engine; and gasoline direct injection. The book includes a chapter on carbon sequestration and optimization of enhanced oil and gas recovery. The contents of this book will be useful to researchers and professionals working on all aspects on combustion.

Download or read book Improvement Trends for Internal Combustion Engines written by Bilge Albayrak Ceper and published by BoD – Books on Demand. This book was released on 2018-03-21 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: Internal combustion engines have remained a challenge due to depending heavily on fossil fuels, which are already limited reserves, and a requirement for improvement in emission levels continuously. The number of advanced technologies such as hybrid systems and low-temperature combustion engines has been introduced, and a number of reports about the use of alternative fuels have been presented in recent years to overcome these challenges. The efforts have made the new concepts to be used in practical along with the new problems which are required advanced control systems. This book presents studies on internal combustion engines with alternative fuels and advanced combustion technologies to obtain efficiency and environment-friendly systems, measurement methodology of exhaust emissions and modelling of a hybrid engine system, and mechanical losses arising from ring-cylinder and ring-groove side contacts as well. The main theme here is to identify solutions for internal combustion engines in terms of fuel consumption, emissions, and performance.

Download or read book Characteristics and Control of Low Temperature Combustion Engines written by Rakesh Kumar Maurya and published by Springer. This book was released on 2017-11-03 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with novel advanced engine combustion technologies having potential of high fuel conversion efficiency along with ultralow NOx and particulate matter (PM) emissions. It offers insight into advanced combustion modes for efficient utilization of gasoline like fuels. Fundamentals of various advanced low temperature combustion (LTC) systems such as HCCI, PCCI, PPC and RCCI engines and their fuel quality requirements are also discussed. Detailed performance, combustion and emissions characteristics of futuristic engine technologies such as PPC and RCCI employing conventional as well as alternative fuels are analyzed and discussed. Special emphasis is placed on soot particle number emission characterization, high load limiting constraints, and fuel effects on combustion characteristics in LTC engines. For closed loop combustion control of LTC engines, sensors, actuators and control strategies are also discussed. The book should prove useful to a broad audience, including graduate students, researchers, and professionals Offers novel technologies for improved and efficient utilization of gasoline like fuels; Deals with most advanced and futuristic engine combustion modes such as PPC and RCCI; Comprehensible presentation of the performance, combustion and emissions characteristics of low temperature combustion (LTC) engines; Deals with closed loop combustion control of advanced LTC engines; State-of-the-art technology book that concisely summarizes the recent advancements in LTC technology. .

Download or read book Biofueled Reciprocating Internal Combustion Engines written by K.A. Subramanian and published by CRC Press. This book was released on 2017-10-02 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biofuels such as ethanol, butanol, and biodiesel have more desirable physico-chemical properties than base petroleum fuels (diesel and gasoline), making them more suitable for use in internal combustion engines. The book begins with a comprehensive review of biofuels and their utilization processes and culminates in an analysis of biofuel quality and impact on engine performance and emissions characteristics, while discussing relevant engine types, combustion aspects and effect on greenhouse gases. It will facilitate scattered information on biofuels and its utilization has to be integrated as a single information source. The information provided in this book would help readers to update their basic knowledge in the area of "biofuels and its utilization in internal combustion engines and its impact Environment and Ecology". It will serve as a reference source for UG/PG/Ph.D. Doctoral Scholars for their projects / research works and can provide valuable information to Researchers from Academic Universities and Industries. Key Features: • Compiles exhaustive information of biofuels and their utilization in internal combustion engines. • Explains engine performance of biofuels • Studies impact of biofuels on greenhouse gases and ecology highlighting integrated bio-energy system. • Discusses fuel quality of different biofuels and their suitability for internal combustion engines. • Details effects of biofuels on combustion and emissions characteristics.

Download or read book A Pathway to Higher Efficiency Internal Combustion Engines Through Thermochemical Recovery and Fuel Reforming written by Flavio Dal Forno Chuahy and published by . This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dual fuel reactivity controlled compression ignition (RCCI) combustion is a promising method to achieve high efficiency with near zero NOx and soot emissions; however, the requirement to carry two fuels on-board has limited practical applications. Advancements in catalytic reforming have demonstrated the ability to generate syngas (a mixture of CO and hydrogen) from a single hydrocarbon stream. The reformed fuel mixture can then be used as a low reactivity fuel stream to enable RCCI out of a single parent fuel. Beyond enabling dual-fuel combustion strategies out of a single parent fuel, fuel reforming can be endothermic and allow recovery of exhaust heat to drive the reforming reactions, potentially improving overall efficiency of the system. Previous works have focused on using reformed fuel to extend the lean limit of spark ignited engines, and enhancing the control of HCCI type combustion. The strategy pairs naturally with advanced dual-fuel combustion strategies, and the use of dual-fuel strategies in the context of on-board reforming and energy recovery has not been explored. Accordingly, the work presented in this dissertation attempts to fill in the gaps in the current literature and provide a pathway to "single" fuel RCCI combustion through a combination of experiments and computational fluid dynamics modeling. Initially, a system level analysis focusing on three common reforming techniques (i.e., partial oxidation, steam reforming and auto-thermal reforming) was conducted to evaluate the potential of reformed fuel. A system layout was proposed for each reforming technique and a detailed thermodynamic analysis using first- and second-law approaches were used to identify the sources of efficiency improvements. The results showed that reformed fuel combustion with a near TDC injection of diesel fuel can increase engine-only efficiency by 4% absolute when compared to a conventional diesel baseline. The efficiency improvements were a result of reduced heat transfer and shorter, more thermodynamically efficient, combustion process. For exothermic reforming processes, losses in the reformer outweigh the improvements to engine efficiency, while for endothermic processes the recovery of exhaust energy was able to allow the system efficiency to retain a large portion of the benefits to the engine combustion. Energy flow analysis showed that the reformer temperature and availability of high grade exhaust heat were the main limiting factors preventing higher efficiencies. RCCI combustion was explored experimentally for its potential to expand on the optimization results and achieve low soot and NOx emissions. The results showed that reformed fuel can be used with diesel to enable RCCI combustion and resulted in low NOx and soot emissions while achieving efficiencies similar to conventional diesel combustion. Experiments showed that the ratio H2/(H2+CO) is an important parameter for optimal engine operation. Under part-load conditions, fractions of H2/(H2+CO) higher than 60% led to pressure oscillations inside the cylinder that substantially increased heat transfer and negated any efficiency benefits. The system analysis approach was applied to the experimental results and showed that chemical equilibrium limited operation of the engine to sub-optimal operating conditions. RCCI combustion was able to achieve "diesel like" system level efficiencies without optimization of either the engine operating conditions or the combustion system. Reformed fuel RCCI was able to provide a pathway to meeting current and future emission targets with a reduction or complete elimination of aftertreatment costs. Particle size distribution experiments showed that addition of reformed fuel had a significant impact on the shape of the particle size distribution. Addition of reformed fuel reduced accumulation-mode particle concentration while increasing nucleation-mode particles. When considering the full range of particle sizes there was a significant increase in total particle concentration. However, when considering currently regulated (Dm>23nm) particles, total concentration was comparable. To address limitations identified in the system analysis of the RCCI experiments a solid oxide fuel cell was combined with the engine into a hybrid electrochemical combustion system. The addition of the fuel cell addresses the limitations by providing sufficient high grade heat to fully drive the reforming reactions. From a system level perspective, the impact of the high frequency oscillations observed in the experiments are reduced, as the system efficiency is less dependent on the engine efficiency. From an engine perspective, the high operating pressures and low reactivity of the anode gas allow reduction of the likelihood of such events. A 0-D system level code was developed and used to find representative conditions for experimental engine validation. The results showed that the system can achieve system electrical efficiencies higher than 70% at 1 MWe power level. Experimental validation showed that the engine was able to operate under both RCCI and HCCI combustion modes and resulted in low emissions and stable combustion. The potential of a hybrid electrochemical combustion system was demonstrated for high efficiency power generation

Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.

Download or read book Diesel Engines and Biodiesel Engines Technologies written by Freddie L. Inambao and published by BoD – Books on Demand. This book was released on 2022-08-17 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Diesel Engines and Biodiesel Engines Technologies explores the conceptual and methodological approaches for the understanding of both diesel engines and biodiesel technologies. The book incorporates reviews of the most significant research findings in both diesel and biodiesel engine production and utilization. It presents technological interventions in biodiesel production and offers a foresight analysis of the perspectives of biodiesel as a future global commodity. It also examines the main challenges that biodiesel will have to overcome in order to play a key role in future energy systems. Furthermore, the book discusses alternative diesel fuels from oils and fats and proposes solutions to issues associated with biodiesel feedstocks, production issues, quality control, viscosity, stability, applications, emissions, and other environmental impacts.

Download or read book Experimental Investigation of Transient RCCI Combustion in a Light Duty Diesel Engine written by and published by . This book was released on 2013 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt: Low Temperature Combustion (LTC) is currently being researched as a way to reduce problematic emissions (i.e., NOx and PM) from compression-ignition engines while maintaining high fuel efficiency. One of the primary types of LTC is Premixed Compression Ignition (PCI), with some examples of PCI being homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI), reactivity controlled compression ignition (RCCI) and partially premixed combustion (PPC). These LTC strategies use early fuel injections to allow sufficient time for air/fuel mixing before combustion. By increasing the amount of air/fuel premixing, NOx and PM emissions can be lowered due to the reduced local and global equivalence ratios. The lean nature of PCI also maintains high thermal efficiency due to the reduced heat transfer losses from the reduced peak combustion temperatures. However, too much air/fuel premixing can lead to rapid energy release rates, limiting the operation space for PCI. To combat this problem, the combustion strategy of interest for the study, RCCI, uses fuel reactivity gradients to increase combustion duration (i.e., reduce the energy release rate) and phasing control, thereby increasing the engine operating space for PCI operation. Previous tests [1-7] have shown promising results for petroleum-based fuels with RCCI. Recent work at Oak Ridge National Laboratory (ORNL) has shown how blends of biofuels with petroleum fuels can improve RCCI combustion performance [8,9] The work sets out to examine biofuel performance over a wide engine operating space both at steady-state and transient operating conditions with RCCI combustion. It is hoped to demonstrate the capability and effects of using bio-derived fuels in place of conventional petroleum-derived fuels for advanced combustion strategies under real-world operating conditions. In RCCI operation, blends of biodiesel and ethanol fuels will be investigated to examine the fuel effects on the combustion event.

Download or read book Advances in Clean Energy written by Anand Ramanathan and published by CRC Press. This book was released on 2020-10-22 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Clean Energy: Production and Application supports sustainable clean energy technology and green fuel for clean combustion by reviewing the pros and cons of currently available technologies specifically for biodiesel production from biomass sources, recent fuel modification strategy, low-temperature combustion technology, including other biofuels as well. Written for researchers, graduate students, and professionals in mechanical engineering, chemical engineering, energy, and environmental engineering, this book: Covers global energy scenarios and future energy demands pertaining to clean energy technologies Provides systematic and detailed coverage of the processes and technologies used for biofuel production Includes new technologies and perspectives, giving up-to-date and state-of-the-art information on research and commercialization Discusses all conversion methods including biochemical and thermochemical Examines the environmental consequences of biomass-based biofuel use

Download or read book Investigation of RCCI Operation with Customized Pistons in a Light duty Multi cylinder Engine Using Dieseline written by and published by . This book was released on 2016 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: In an attempt to increase efficiency and lower critical and highly regulated emissions (i.e., NOx, PM and CO2) many advanced combustion strategies have been investigated. Most of the current strategies fall into the category of low temperature combustion (LTC), which allow emissions mandates to be met in-cylinder along with anticipated reduction in cost and complexity. These strategies, such as homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI), partially premixed combustion (PPC) and reactivity controlled compression ignition (RCCI), use early injection timings, resulting in a highly lean charge with increased specific heat ratios to improve thermal efficiency and reduce PM emissions. Lower combustion temperatures also avoid the activation of NOx formation reactions. However, the lean air/fuel ratio decreases fuel oxidation rates of CO and HC and, due to longer ignition delays with high peak pressure rise rate (PPRR) and heat release rates (HRR), confines the engine’s operating loads and speeds. A strategy to reduce these negative effects of LTC is RCCI, which generally uses two fuels with different reactivities in order to optimize ignitability and equivalence ratio stratification. It has demonstrated improvements in efficiency and low NOx and PM emissions by utilizing in-cylinder fuel blending, while the simultaneous optimization of fuel reactivity results in increased engine operating space. The current work investigates Reactivity Controlled Compression Ignition (RCCI) combustion in a light-duty multi-cylinder engine over steady-state and transient operating conditions using also fast exhaust sampling emissions equipment for UHC, NO and PM measurements. A “single-fuel ” approach for RCCI combustion was studied using port-injected and direct-injected (DI) cetane improved gasoline with custom designed, 15.3:1 compression ratio, pistons. In addition, experiments were conducted using mixtures of gasoline and diesel, i.e., “dieseline”, as the high reactivity fuel. The experiments were performed over a broad selection of “ad hoc” load and speed points in order to examine performance and emission effects of a less reactive DI fuel mixture to in turn reduce the need for a second fuel. This work also helps to demonstrate the requirements for high levels of boost in a multi-cylinder engine during RCCI operation. Comparisons were also made to an HCCI/GCI like combustion strategy using similar gasoline/diesel fuel blends.

Download or read book Gasoline Compression Ignition Technology written by Gautam Kalghatgi and published by Springer Nature. This book was released on 2022-01-17 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on gasoline compression ignition (GCI) which offers the prospect of engines with high efficiency and low exhaust emissions at a lower cost. A GCI engine is a compression ignition (CI) engine which is run on gasoline-like fuels (even on low-octane gasoline), making it significantly easier to control particulates and NOx but with high efficiency. The state of the art development to make GCI combustion feasible on practical vehicles is highlighted, e.g., on overcoming problems on cold start, high-pressure rise rates at high loads, transients, and HC and CO emissions. This book will be a useful guide to those in academia and industry.

Download or read book DESIGN OF REAL TIME COMBUSTION FEEDBACK SYSTEM AND EXPERIMENTAL STUDY OF AN RCCI ENGINE FOR CONTROL written by and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Abstract : Premixed compression ignition (PCI) technologies offer high efficiency and low emissions but are usually confined by limited operation range as well as high pressure rise and heat release rate. In this work, a more recently developed PCI mode is explored where in-cylinder blending of two fuels with different auto-ignition characteristics (diesel and gasoline) is utilized to create reactivity stratification such that heat release rate and combustion timing can be controlled. This mode has been defined as Reactivity Controlled Compression Ignition (RCCI). As part of this thesis, the main aim is to study various parameters that can be used to control combustion phasing. Also, steady state mapping of the engine is done so as to explore the operating range for the current engine setup. Best efficiencies as well as highest loads are obtained for higher Premixed Ratio (PR) values and advanced Start of Injection (SOI) timings, where as lower PR fuel blends are needed to achieve low load limit. The analysis is also extended to transient RCCI operation for observing various dynamics involved and their effects on combustion phasing. As part of realizing full-load range operation, switching to conventional Spark-Ignition (SI) combustion mode is also carried out. Various dynamics involved in the switching process are captured. A cycle-by-cycle closed loop combustion controller is designed and implemented on the engine to achieve optimum combustion phasing during transient engine operation. To provide feedback of combustion parameters like engine load and combustion phasing to the closed loop controller, a real-time combustion feedback system is designed and implemented utilizing Field Programmable Gate Array (FPGA).

Download or read book The Future of Internal Combustion Engines written by Antonio Paolo Carlucci and published by BoD – Books on Demand. This book was released on 2019-09-11 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Based on previsions, the reciprocating internal combustion engine will continue to be widely used in all sectors: transport, industry, and energy production. Therefore, its development, while complying with the limitations of pollutants as well as CO2 emission levels and maintaining or increasing performance, will certainly continue for the next few decades.In the last three decades, a significant effort has been made to reduce pollutant emission levels. More recently, attention has been given to CO2 emission levels too.It is widely recognized that one single technology will not completely solve the problem of CO2 emissions in the atmosphere. Rather, the different technologies already available will have to be integrated, and new technologies developed, to obtain substantial CO2 abatement.

Download or read book Modeling and Control of Maximum Pressure Rise Rate in RCCI Engines written by and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Abstract : Low Temperature Combustion (LTC) is a combustion strategy that burns fuel at lower temperatures and leaner mixtures in order to achieve high efficiency and near zero NOx emissions. Since the combustion happens at lower temperatures it inhibits the formation of NOx and soot emissions. One such strategy is Reactivity Controlled Compression Ignition (RCCI). One characteristic of RCCI combustion and LTC com- bustion in general is short burn durations which leads to high Pressure Rise Rates (PRR). This limits the operation of these engines to lower loads as at high loads, the Maximum Pressure Rise Rate (MPRR) hinders the use of this combustion strategy. This thesis focuses on the development of a model based controller that can control the Crank Angle for 50% mass fraction burn (CA50) and Indicated Mean Effective Pressure (IMEP) of an RCCI engine while limiting the MPRR to a pre determined limit. A Control Oriented Model (COM) is developed to predict the MPRR in an RCCI engine. This COM is then validated against experimental data. A statistical analysis of the experimental data is conducted to understand the accuracy of the COM. The results show that the COM is able to predict the MPRR with reasonable accuracy in steady state and transient conditions. Also, the COM is able to capture the trends during transient operation. This COM is then included in an existing cycle by cycle dynamic RCCI engine model and used to develop a Linear Parameter Varying (LPV) representation of an RCCI engine using Data Driven Modeling (DDM) approach with Support Vector Machines (SVM). This LPV representation is then used along with a Model Predictive Controller (MPC) to control the CA50 and IMEP of the RCCI engine model while limiting the MPRR. The controller was able to track the desired CA50 and IMEP with a mean error of 0.9 CAD and 4.7 KPa respectively while maintaining the MPRR below 5.8 bar/CAD.

Download or read book Prospects of Alternative Transportation Fuels written by Akhilendra P Singh and published by Springer. This book was released on 2017-11-28 with total page 408 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses different types of alternative fuels, including biodiesel, alcohol, synthetic fuels, compressed natural gas (CNG) and its blend with hydrogen, HCNG, and provides detailed information on the utilization of these alternative fuels in internal combustion (IC) engines. Further, it presents methods for production of these alternative fuels and explores advanced combustion techniques, such as low-temperature and dual-fuel combustion, using alternative fuels. It includes a chapter on the soot morphology of biodiesel, which focuses on the toxicity. There are also four chapters on hydrogen-fueled engines, which discuss use of hydrogen in IC engines and also provide important information on the methodologies. This book is a valuable resource for researchers and practicing engineers alike.

Download or read book Reciprocating Engine Combustion Diagnostics written by Rakesh Kumar Maurya and published by Springer. This book was released on 2019-03-19 with total page 616 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with in-cylinder pressure measurement and its post-processing for combustion quality analysis of conventional and advanced reciprocating engines. It offers insight into knocking and combustion stability analysis techniques and algorithms in SI, CI, and LTC engines, and places special emphasis on the digital signal processing of in-cylinder pressure signal for online and offline applications. The text gives a detailed description on sensors for combustion measurement, data acquisition, and methods for estimation of performance and combustion parameters. The information provided in this book enhances readers’ basic knowledge of engine combustion diagnostics and serves as a comprehensive, ready reference for a broad audience including graduate students, course instructors, researchers, and practicing engineers in the automotive, oil and other industries concerned with internal combustion engines.