Download or read book High Speed CMOS Circuits for Optical Receivers written by Jafar Savoj and published by Springer Science & Business Media. This book was released on 2007-05-08 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: With the exponential growth of the number of Internet nodes, the volume of the data transported on the backbone has increased with the same trend. The load of the global Internet backbone will soon increase to tens of terabits per second. This indicates that the backbone bandwidth requirements will increase by a factor of 50 to 100 every seven years. Transportation of such high volumes of data requires suitable media with low loss and high bandwidth. Among the available transmission media, optical fibers achieve the best performance in terms of loss and bandwidth. High-speed data can be transported over hundreds of kilometers of single-mode fiber without significant loss in signal integrity. These fibers progressively benefit from reduction of cost and improvement of perf- mance. Meanwhile, the electronic interfaces used in an optical network are not capable of exploiting the ultimate bandwidth of the fiber, limiting the throughput of the network. Different solutions at both the system and the circuit levels have been proposed to increase the data rate of the backbone. System-level solutions are based on the utilization of wave-division multiplexing (WDM), using different colors of light to transmit s- eral sequences simultaneously. In parallel with that, a great deal of effort has been put into increasing the operating rate of the electronic transceivers using highly-developed fabrication processes and novel c- cuit techniques.
Download or read book High Speed Optical Receivers with Integrated Photodiode in Nanoscale CMOS written by Filip Tavernier and published by Springer Science & Business Media. This book was released on 2011-06-20 with total page 231 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the design of optical receivers that use the most economical integration technology, while enabling performance that is typically only found in very expensive devices. To achieve this, all necessary functionality, from light detection to digital output, is integrated on a single piece of silicon. All building blocks are thoroughly discussed, including photodiodes, transimpedance amplifiers, equalizers and post amplifiers.
Download or read book Broadband Opto Electrical Receivers in Standard CMOS written by Carolien Hermans and published by Springer Science & Business Media. This book was released on 2007-06-13 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book opens with the basics of the design of opto-electronic interface circuits. The text continues with an in-depth analysis of the photodiode, transimpedance amplifier (TIA) and limiting amplifier (LA). To thoroughly describe light detection mechanisms in silicon, first a one-dimensional and second a two-dimensional model is developed. All material is experimentally verified with several CMOS implementations, with ultimately a fully integrated Gbit/s optical receiver front-end including photodiode, TIA and LA.
Download or read book Design of Analog CMOS Integrated Circuits written by Behzad Razavi and published by . This book was released on 2001 with total page 684 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design of Integrated Circuits for Optical Communications written by Behzad Razavi and published by John Wiley & Sons. This book was released on 2012-09-14 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: The only book on integrated circuits for optical communications that fully covers High-Speed IOs, PLLs, CDRs, and transceiver design including optical communication The increasing demand for high-speed transport of data has revitalized optical communications, leading to extensive work on high-speed device and circuit design. With the proliferation of the Internet and the rise in the speed of microprocessors and memories, the transport of data continues to be the bottleneck, motivating work on faster communication channels. Design of Integrated Circuits for Optical Communications, Second Edition deals with the design of high-speed integrated circuits for optical communication transceivers. Building upon a detailed understanding of optical devices, the book describes the analysis and design of critical building blocks, such as transimpedance and limiting amplifiers, laser drivers, phase-locked loops, oscillators, clock and data recovery circuits, and multiplexers. The Second Edition of this bestselling textbook has been fully updated with: A tutorial treatment of broadband circuits for both students and engineers New and unique information dealing with clock and data recovery circuits and multiplexers A chapter dedicated to burst-mode optical communications A detailed study of new circuit developments for optical transceivers An examination of recent implementations in CMOS technology This text is ideal for senior graduate students and engineers involved in high-speed circuit design for optical communications, as well as the more general field of wireline communications.
Download or read book High speed Optical Transceivers Integrated Circuits Designs And Optical Devices Techniques written by Yuyu Liu and published by World Scientific. This book was released on 2006-03-09 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the unique advantages and large inherent transmission capacity of optical fiber communication systems. The long-term and high-risk research challenges of optical transceivers are analyzed with a view to sustaining the seemingly insatiable demand for bandwidth. A broad coverage of topics relating to the design of high-speed optical devices and integrated circuits, oriented to low power, low cost, and small area, is discussed.Written by specialists with many years of research and engineering experience in the field of optical fiber communication, this book is essential for an audience dedicated to the development of integrated electronic systems for optical communication applications. It can also be used as a supplementary text for graduate courses on optical transceiver IC design.
Download or read book Broadband Circuits for Optical Fiber Communication written by Eduard Säckinger and published by John Wiley & Sons. This book was released on 2005-05-27 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: An expert guide to the new and emerging field of broadband circuits for optical fiber communication This exciting publication makes it easy for readers to enter into and deepen their knowledge of the new and emerging field of broadband circuits for optical fiber communication. The author's selection and organization of material have been developed, tested, and refined from his many industry courses and seminars. Five types of broadband circuits are discussed in detail: * Transimpedance amplifiers * Limiting amplifiers * Automatic gain control (AGC) amplifiers * Lasers drivers * Modulator drivers Essential background on optical fiber, photodetectors, lasers, modulators, and receiver theory is presented to help readers understand the system environment in which these broadband circuits operate. For each circuit type, the main specifications and their impact on system performance are explained and illustrated with numerical values. Next, the circuit concepts are discussed and illustrated with practical implementations. A broad range of circuits in MESFET, HFET, BJT, HBT, BiCMOS, and CMOS technologies is covered. Emphasis is on circuits for digital, continuous-mode transmission in the 2.5 to 40 Gb/s range, typically used in SONET, SDH, and Gigabit Ethernet applications. Burst-mode circuits for passive optical networks (PON) and analog circuits for hybrid fiber-coax (HFC) cable-TV applications also are discussed. Learning aids are provided throughout the text to help readers grasp and apply difficult concepts and techniques, including: * Chapter summaries that highlight the key points * Problem-and-answer sections to help readers apply their new knowledge * Research directions that point to exciting new technological breakthroughs on the horizon * Product examples that show the performance of actual broadband circuits * Appendices that cover eye diagrams, differential circuits, S parameters, transistors, and technologies * A bibliography that leads readers to more complete and in-depth treatment of specialized topics This is a superior learning tool for upper-level undergraduates and graduate-level students in circuit design and optical fiber communication. Unlike other texts that concentrate on analog circuits in general or mostly on optics, this text provides balanced coverage of electronic, optic, and system issues. Professionals in the fiber optic industry will find it an excellent reference, incorporating the latest technology and discoveries in the industry.
Download or read book Analysis and Design of Transimpedance Amplifiers for Optical Receivers written by Eduard Säckinger and published by John Wiley & Sons. This book was released on 2017-10-09 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: An up-to-date, comprehensive guide for advanced electrical engineering studentsand electrical engineers working in the IC and optical industries This book covers the major transimpedance amplifier (TIA) topologies and their circuit implementations for optical receivers. This includes the shunt-feedback TIA, common-base TIA, common-gate TIA, regulated-cascode TIA, distributed-amplifier TIA, nonresistive feedback TIA, current-mode TIA, burst-mode TIA, and analog-receiver TIA. The noise, transimpedance, and other performance parameters of these circuits are analyzed and optimized. Topics of interest include post amplifiers, differential vs. single-ended TIAs, DC input current control, and adaptive transimpedance. The book features real-world examples of TIA circuits for a variety of receivers (direct detection, coherent, burst-mode, etc.) implemented in a broad array of technologies (HBT, BiCMOS, CMOS, etc.). The book begins with an introduction to optical communication systems, signals, and standards. It then moves on to discussions of optical fiber and photodetectors. This discussion includes p-i-n photodetectors; avalanche photodetectors (APD); optically preamplified detectors; integrated detectors, including detectors for silicon photonics; and detectors for phase-modulated signals, including coherent detectors. This is followed by coverage of the optical receiver at the system level: the relationship between noise, sensitivity, optical signal-to-noise ratio (OSNR), and bit-error rate (BER) is explained; receiver impairments, such as intersymbol interference (ISI), are covered. In addition, the author presents TIA specifications and illustrates them with example values from recent product data sheets. The book also includes: Many numerical examples throughout that help make the material more concrete for readers Real-world product examples that show the performance of actual IC designs Chapter summaries that highlight the key points Problems and their solutions for readers who want to practice and deepen their understanding of the material Appendices that cover communication signals, eye diagrams, timing jitter, nonlinearity, adaptive equalizers, decision point control, forward error correction (FEC), and second-order low-pass transfer functions Analysis and Design of Transimpedance Amplifiers for Optical Receivers belongs on the reference shelves of every electrical engineer working in the IC and optical industries. It also can serve as a textbook for upper-level undergraduates and graduate students studying integrated circuit design and optical communication.
Download or read book High Speed Photodiodes in Standard CMOS Technology written by Sasa Radovanovic and published by Springer Science & Business Media. This book was released on 2006-10-11 with total page 159 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-speed Photodiodes in Standard CMOS Technology describes high-speed photodiodes in standard CMOS technology which allow monolithic integration of optical receivers for short-haul communication. For short haul communication the cost aspect is important , and therefore it is desirable that the optical receiver can be integrated in the same CMOS technology as the rest of the system. If this is possible then ultimately a singe-chip system including optical inputs becomes feasible, eliminating EMC and crosstalk problems, while data rate can be extremely high. The problem of photodiodes in standard CMOS technology it that they have very limited bandwidth, allowing data rates up to only 50Mbit per second. High-speed Photodiodes in Standard CMOS Technology first analyzes the photodiode behaviour and compares existing solutions to enhance the speed. After this, the book introduces a new and robust electronic equalizer technique that makes data rates of 3Gb/s possible, without changing the manufacturing technology. The application of this technique can be found in short haul fibre communication, optical printed circuit boards, but also photodiodes for laser disks.
Download or read book High speed Integrated Circuit Technology written by Mark J. W. Rodwell and published by World Scientific. This book was released on 2001 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the state of the art of very high speed digital integrated circuits. Commercial applications are in fiber optic transmission systems operating at 10, 40, and 100 Gb/s, while the military application is ADCs and DACs for microwave radar. The book contains detailed descriptions of the design, fabrication, and performance of wideband Si/SiGe-, GaAs-, and InP-based bipolar transistors. The analysis, design, and performance of high speed CMOS, silicon bipolar, and III-V digital ICs are presented in detail, with emphasis on application in optical fiber transmission and mixed signal ICs. The underlying physics and circuit design of rapid single flux quantum (RSFQ) superconducting logic circuits are reviewed, and there is extensive coverage of recent integrated circuit results in this technology.
Download or read book High Frequency Integrated Circuits written by Sorin Voinigescu and published by Cambridge University Press. This book was released on 2013-02-28 with total page 921 pages. Available in PDF, EPUB and Kindle. Book excerpt: A transistor-level, design-intensive overview of high speed and high frequency monolithic integrated circuits for wireless and broadband systems from 2 GHz to 200 GHz, this comprehensive text covers high-speed, RF, mm-wave, and optical fibre circuits using nanoscale CMOS, SiGe BiCMOS, and III-V technologies. Step-by-step design methodologies, end-of chapter problems, and practical simulation and design projects are provided, making this an ideal resource for senior undergraduate and graduate courses in circuit design. With an emphasis on device-circuit topology interaction and optimization, it gives circuit designers and students alike an in-depth understanding of device structures and process limitations affecting circuit performance.
Download or read book Optical Interconnects written by Lorenzo Pavesi and published by Springer. This book was released on 2007-05-17 with total page 397 pages. Available in PDF, EPUB and Kindle. Book excerpt: Optical Interconnects provides a fascinating picture of the state of the art in optical interconnects and a perspective on what can be expected in the near future. It is composed of selected reviews authored by world leaders in the field, and these reviews are written from either an academic or industrial viewpoint. An in-depth discussion of the path towards fully-integrated optical interconnects in microelectronics is presented. This book will be useful not only to physicists, chemists, materials scientists, and engineers but also to graduate students who are interested in the fields of microelectronics and optoelectronics.
Download or read book Introduction to Fiber Optic Communications written by Rongqing Hui and published by Academic Press. This book was released on 2019-06-12 with total page 662 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to Fiber-Optic Communications provides students with the most up-to-date, comprehensive coverage of modern optical fiber communications and applications, striking a fine balance between theory and practice that avoids excessive mathematics and derivations. Unlike other textbooks currently available, this book covers all of the important recent technologies and developments in the field, including electro-optic modulators, coherent optical systems, and silicon integrated photonic circuits. Filled with practical, relevant worked examples and exercise problems, the book presents complete coverage of the topics that optical and communications engineering students need to be successful. From principles of optical and optoelectronic components, to optical transmission system design, and from conventional optical fiber links, to more useful optical communication systems with advanced modulation formats and high-speed DSP, this book covers the necessities on the topic, even including today's important application areas of passive optical networks, datacenters and optical interconnections. - Covers fiber-optic communication system fundamentals, design rules and terminologies - Provides students with an understanding of the physical principles and characteristics of passive and active fiber-optic components - Teaches students how to perform fiber-optic system design, performance evaluation and troubleshooting - Includes modern advances in modulation and decoding strategies
Download or read book Highly Sensitive Optical Receivers written by Kerstin Schneider and published by Springer Science & Business Media. This book was released on 2006-11-10 with total page 203 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highly Sensitive Optical Receivers primarily treats the circuit design of optical receivers with external photodiodes. Continuous-mode and burst-mode receivers are compared. The monograph first summarizes the basics of III/V photodetectors, transistor and noise models, bit-error rate, sensitivity and analog circuit design, thus enabling readers to understand the circuits described in the main part of the book. In order to cover the topic comprehensively, detailed descriptions of receivers for optical data communication in general and, in particular, optical burst-mode receivers in deep-sub-μm CMOS are presented. Numerous detailed and elaborate illustrations facilitate better understanding.
Download or read book Smart Sensors at the IoT Frontier written by Hiroto Yasuura and published by Springer. This book was released on 2017-05-29 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes technology used for effective sensing of our physical world and intelligent processing techniques for sensed information, which are essential to the success of Internet of Things (IoT). The authors provide a multidisciplinary view of sensor technology from materials, process, circuits, to big data domains and they showcase smart sensor systems in real applications including smart home, transportation, medical, environmental, agricultural, etc. Unlike earlier books on sensors, this book provides a “global” view on smart sensors covering abstraction levels from device, circuit, systems, and algorithms.
Download or read book Optoelectronic Integrated Circuit Design and Device Modeling written by Jianjun Gao and published by John Wiley & Sons. This book was released on 2011-09-19 with total page 258 pages. Available in PDF, EPUB and Kindle. Book excerpt: In Optoelectronic Integrated Circuit Design and Device Modeling, Professor Jianjun Gao introduces the fundamentals and modeling techniques of optoelectronic devices used in high-speed optical transmission systems. Gao covers electronic circuit elements such as FET, HBT, MOSFET, as well as design techniques for advanced optical transmitter and receiver front-end circuits. The book includes an overview of optical communication systems and computer-aided optoelectronic IC design before going over the basic concept of laser diodes. This is followed by modeling and parameter extraction techniques of lasers and photodiodes. Gao covers high-speed electronic semiconductor devices, optical transmitter design, and optical receiver design in the final three chapters. Addresses a gap within the rapidly growing area of transmitter and receiver modeling in OEICs Explains diode physics before device modeling, helping readers understand their equivalent circuit models Provides comprehensive explanations for E/O and O/E conversions done with laser and photodiodes Covers an extensive range of devices for high-speed applications Accessible for students new to microwaves Presentation slides available for instructor use This book is primarily aimed at practicing engineers, researchers, and post-graduates in the areas of RF, microwaves, IC design, photonics and lasers, and solid state devices. The book is also a strong supplement for senior undergraduates taking courses in RF and microwaves. Lecture materials for instructors available at www.wiley.com/go/gao
Download or read book Integrated Optical Interconnect Architectures for Embedded Systems written by Ian O'Connor and published by Springer Science & Business Media. This book was released on 2012-11-07 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a broad overview of current research in optical interconnect technologies and architectures. Introductory chapters on high-performance computing and the associated issues in conventional interconnect architectures, and on the fundamental building blocks for integrated optical interconnect, provide the foundations for the bulk of the book which brings together leading experts in the field of optical interconnect architectures for data communication. Particular emphasis is given to the ways in which the photonic components are assembled into architectures to address the needs of data-intensive on-chip communication, and to the performance evaluation of such architectures for specific applications.
