Download or read book Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped with a Mean Camberline Strip written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-16 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental and computational studies have been performed to investigate the detailed distribution of convective heat transfer coefficients on the first-stage blade tip surface for a geometry typical of large power generation turbines (greater than 100 MW) In a previous work the numerical heat transfer results for a sharp edge blade tip and a radiused blade tip were presented. More recently several other tip treatments have been considered for which the tip heat transfer has been measured and documented. This paper is concerned with the numerical prediction of the tip surface heat transfer for radiused blade tip equipped with mean-camberline strip (or "squealer" as it is often called). The heat transfer results are compared with the experimental results and discussed. The effectiveness of the mean-camberline strip in reducing the tip leakage and the tip heat transfer as compared to a radiused edge tip and sharp edge tip was studied. The calculations show that the sharp edge tip works best (among the cases considered) in reducing the tip leakage flow and the tip heat transfer. Ameri, A.A. Glenn Research Center NASA/CR-2001-210764, NAS 1.26:210764, E-12693, Rept-2001-GT-0156

Download or read book Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped with a Mean Camberline Strip written by and published by . This book was released on 2001 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped with a Mean Camberline Strip Final Report NASA written by and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped with a Mean camberline Strip Final Report Nasa cr 2001 210764 Aug written by and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Determination of Gas to blade Convection Heat transfer Coefficients on a Forced convection Water cooled Single stage Aluminum Turbine written by John C. Freche and published by . This book was released on 1951 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.

Download or read book Heat Transfer and Flow on the First Stage Blade Tip of a Power Generation Gas Turbine Part 1 Experimental Results written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-15 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: A combined computational and experimental study has been performed to investigate the detailed distribution of convective heat transfer coefficients on the first stage blade tip surface for a geometry typical of large power generation turbines(>100MW). This paper is concerned with the design and execution of the experimental portion of the study. A stationary blade cascade experiment has been run consisting of three airfoils, the center airfoil having a variable tip gap clearance. The airfoil models the aerodynamic tip section of a high pressure turbine blade with inlet Mach number of 0.30, exit Mach number of 0.75, pressure ratio of 1.45, exit Reynolds number based on axial chord of 2.57 x 10(exp 6), and total turning of about 110 degrees. A hue detection based liquid crystal method is used to obtain the detailed heat transfer coefficient distribution on the blade tip surface for flat, smooth tip surfaces with both sharp and rounded edges. The cascade inlet turbulence intensity level took on values of either 5% or 9%. The cascade also models the casing recess in the shroud surface ahead of the blade. Experimental results are shown for the pressure distribution measurements on the airfoil near the tip gap, on the blade tip surface, and on the opposite shroud surface. Tip surface heat transfer coefficient distributions are shown for sharp-edge and rounded-edge tip geometries at each of the inlet turbulence intensity levels. Bunker, Ronald S. and Bailey, Jeremy C. and Ameri, Ali A. Glenn Research Center NASA/CR-1999-209152, NAS 1.26:209152, E-11660, ASME-99-GT-169

Download or read book Analysis of Gas Turbine Rotor Blade Tip and Shroud Heat Transfer written by Ali A. Ameri and published by . This book was released on 1996 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress &Exhibition Birmingham, UK - June 10-13, 1996.

Download or read book Heat Transfer and Flow on the First Stage Blade Tip of a Power Generation Gas Turbine written by and published by . This book was released on 1999 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Heat Transfer and Flow on the First Stage Blade Tip of a Power Generation Gas Turbine written by Ali A. Ameri and published by . This book was released on 1999 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Effect of Blade tip Crossover Passages on Natural convection Water cooling of Gas turbine Blades written by Charles F. Zalabak and published by . This book was released on 1956 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: A water-cooled turbine was fabricated and tested to determine the effect of a connecting passage at the turbine rotor blade tip between a radial coolant passage 0.10 inch in diameter (length-diameter ratio = 25.5) and radial coolant passages in the legnth-diameter range of 5.1 to 20.4. Coolant flow through the connecting passage is induced by free-convection forces in the radial passages.

Download or read book Engineering Applications of Computational Fluid Dynamics written by Ku Zilati Ku Shaari and published by Springer. This book was released on 2014-11-28 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents the results of Computational Fluid Dynamics (CFD) analysis that can be used for conceptual studies of product design, detail product development, process troubleshooting. It demonstrates the benefit of CFD modeling as a cost saving, timely, safe and easy to scale-up methodology.

Download or read book ASME Technical Papers written by and published by . This book was released on 2001 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.

Download or read book Journal of Heat Transfer written by and published by . This book was released on 2005 with total page 484 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Journal of Thermophysics and Heat Transfer written by and published by . This book was released on 2006 with total page 996 pages. Available in PDF, EPUB and Kindle. Book excerpt: This journal is devoted to the advancement of the science and technology of thermophysics and heat transfer through the dissemination of original research papers disclosing new technical knowledge and exploratory developments and applications based on new knowledge. It publishes papers that deal with the properties and mechanisms involved in thermal energy transfer and storage in gases, liquids, and solids or combinations thereof. These studies include conductive, convective, and radiative modes alone or in combination and the effects of the environment.

Download or read book Heat Transfer and Flow on the First Stage Blade Tip of a Power Generation Gas Turbine Part 2 Simulation Results written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-15 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: A combined experimental and computational study has been performed to investigate the detailed distribution of convective heat transfer coefficients on the first stage blade tip surface for a geometry typical of large power generation turbines (>1OOMW). This paper is concerned with the numerical prediction of the tip surface heat transfer. Good comparison with the experimental measured distribution was achieved through accurate modeling of the most important features of the blade passage and heating arrangement as well as the details of experimental rig likely to affect the tip heat transfer. A sharp edge and a radiused edge tip were considered. The results using the radiused edge tip agreed better with the experimental data. This improved agreement was attributed to the absence of edge separation on the tip of the radiused edge blade. Ameri, A. A. and Bunker, R. S. Glenn Research Center NASA/CR-1999-209151/PT2, NAS 1.26:209151/PT2, E-11656/PT2, ASME 99-GT-283/PT2