Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.
Download or read book Gas Turbine Heat Transfer and Cooling Technology written by Je-Chin Han and published by Taylor & Francis. This book was released on 2012-11-27 with total page 865 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, this second edition focuses on gas turbine heat transfer issues and their associated cooling technologies for aircraft and land-based gas turbines. It provides information on state-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling schemes. The book also offers updated experimental methods for gas turbine heat transfer and cooling research, as well as advanced computational models for gas turbine heat transfer and cooling performance predictions. The authors provide suggestions for future research within this technology and includes 800 illustrations to help clarify concepts and instruction.
Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.
Download or read book Heat Transfer in Gas Turbines written by Bengt Sundén and published by Witpress. This book was released on 2001 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title presents and reflects current active research on various heat transfer topics and related phenomena in gas turbine systems. It begins with a general introduction to gas turbine heat transfer, before moving on to specific areas.
Download or read book Impingement Jet Cooling in Gas Turbines written by R.S. Amano and published by WIT Press. This book was released on 2014-05-28 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to the requirement for enhanced cooling technologies on modern gas turbine engines, advanced research and development has had to take place in field of thermal engineering. Among the gas turbine cooling technologies, impingement jet cooling is one of the most effective in terms of cooling effectiveness, manufacturability and cost. The chapters contained in this book describe research on state-of-the-art and advanced cooling technologies that have been developed, or that are being researched, with a variety of approaches from theoretical, experimental, and CFD studies. The authors of the chapters have been selected from some of the most active researchers and scientists on the subject. This is the first to book published on the topics of gas turbines and heat transfer to focus on impingement cooling alone.
Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.
Download or read book Heat Transfer and Cooling in Gas Turbines written by and published by . This book was released on 1985 with total page 530 pages. Available in PDF, EPUB and Kindle. Book excerpt: Partial Contents: Rotating Heat Transfer on a Multipass Cooling Geometry; Pressure Drop and Heat Transfer Characteristics of Circular and Oblong Low Aspect Ratio Pin Fins; External Heat Transfer Study on a HP Turbine Rotor Blade; Effects of Wakes on the Heat Transfer in Gas Turbine Cascades; Effect of Hole Geometry, Wall Curvature and Pressure Gradient on Film Cooling Downstream of a Single Row; The Effect of Density Ratio on the Film-Cooling of a Flat Plate; Shroud Segments for Unshrouded Blade Turbines; Heat Transfer Test Evaluation of the Shell-Spar Blade Cooling Concept Applied to Industrial Gas Turbines; Heat-Flux Measurements and Analysis for a Rotating Turbine Stage; Calculation of Laminar-Turbulent Boundary Layer Transition on Turbine Blades; A Model for Correlating Flat Plate Film Cooling Effectiveness for Rows of Round Holes; Heat Transfer in Gas Turbine Combustors; Effectiveness Measurements for a Cooling Film Disrupted by a Single Jet with Wall Plunging; Full Coverage Impingement Heat Transfer: The Variation in Pitch to Diameter Ratio at a Constant Gap; The Measurement of Local Heat Transfer Coefficients in Blade Cooling Geometries; High Frequency Response Heat Flux Gauge for Metal Blading; Transient Thermal Behavior of a Compressor Rotor with Ventilation - Test Results under Simulated Engine Conditions; Heat Exchangers in Regenerative Gas Turbine Cycles.
Download or read book Gas Turbines for Electric Power Generation written by S. Can Gülen and published by Cambridge University Press. This book was released on 2019-02-14 with total page 735 pages. Available in PDF, EPUB and Kindle. Book excerpt: Everything you wanted to know about industrial gas turbines for electric power generation in one source with hard-to-find, hands-on technical information.
Download or read book Fundamental Heat Transfer Research for Gas Turbine Engines written by and published by . This book was released on 1980 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Combustion and Heat Transfer in Gas Turbine Systems written by E. R. Norster and published by Elsevier. This book was released on 2013-10-22 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion and Heat Transfer in Gas Turbine Systems is a compilation of papers from the Proceedings of an International Propulsion Symposium held at the College of Aeronautics, Cranfield in April 1969. This compilation deals with research done by academic and scientific institutions and of industrial organizations, with some research papers covering atomization, fuels, and high-temperature materials. One paper describes the combustion system of the Concorde engine used in commercial flights, temperature of metal parts, and some design modifications to increase the mechanical life of the combustion system. Another paper discusses the evolution of the RB 162 combustion system that is used in the vertical takeoff and landing aircrafts. The RB 162 has many design features of the earlier single reversal chamber and differs in only one or two points. The book then notes the necessity of a plenum chamber burning to further development of supersonic engines and flight. One paper also proposes an alternative theory to the traditional ignition theory of altitude relighting such as those developed by Lewis and von Elbe. Another paper reposts on some observations made of the atomizing characteristics of air-blast atomizers and proposes simple changes to improve the performance of the atomizer by prefilming and allowing air to both sides of the fuel. This compilation will prove very helpful for aeronautical engineers, aviation designers, physicists, students of engineering, and readers who are interested in the design and development of jet engines and supersonic aircrafts.
Download or read book Survey of Advantages and Problems Associated with Transpiration Cooling and Film Cooling of Gas turbine Blades written by Ernst Rudolf Georg Eckert and published by . This book was released on 1951 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summary: Transpiration and film cooling promise to be effective methods of cooling gas-turbine blades; consequently, analytical and experimental investigations are being conducted to obtain a better understanding of these processes. This report serves as an introduction to these cooling methods, explains the physical processes, and surveys the information available for predicting blade temperatures and heat-transfer rates. In addition, the difficulties encountered in obtaining a uniform blade temperature are discussed, and the possibilities of correcting these difficulties are indicated. Air is the only coolant considered in the application of these cooling methods.
Download or read book Cooling of Gas Turbines written by W. Byron Brown and published by . This book was released on 1948 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cooling of Gas Turbines written by W. Byron Brown and published by . This book was released on 1947 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cooling of Gas Turbines written by Lincoln Wolfenstein and published by . This book was released on 1947 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Basic Aspects of Gas Turbine Heat Transfer written by Shailendra Naik and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of gas turbines for power generation and electricity production in both single cycle and combined cycle plant operation is extensive and will continue to globally grow into the future. Due to its high power density and ability to convert gaseous and liquid fuel into mechanical work with very high thermodynamic efficiencies, significant efforts continue today to further increase both the power output and thermodynamic efficiencies of the gas turbine. In particular, the aerothermal design of gas turbine components has progressed at a rapid pace in the last decade with all gas turbine manufacturers, in order to achieve higher thermodynamic efficiencies. This has been achieved by using higher turbine inlet temperatures and pressures, advanced turbine aerodynamics and efficient cooling systems of turbine airofoils, and advanced high temperature alloys, metallic coatings, and ceramic thermal barrier coatings. In this chapter, issues related to the thermal design of gas turbine blades are highlighted and several heat transfer technologies are examined, such as convective cooling, impingement cooling, film cooling, and application of thermal barrier coatings. Typical methods for validating the thermal designs of gas turbine airofoils are also outlined.
Download or read book Analysis and Comparison of Wall Cooling Schemes for Advanced Gas Turbine Applications written by Raymond Strong Colladay and published by . This book was released on 1972 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: The relative performance of (1) counterflow film cooling, (2) parallel-flow film cooling, (3) convection cooling, (4) adiabatic film cooling, (5) transpiration cooling, and (6) full-coverage film cooling was investigated for heat loading conditions expected in future gas turbine engines. Assumed in the analysis were hot-gas conditions of 2200 K (3500 F) recovery temperature, 5 to 40 atmospheres total pressure, and 0.6 gas Mach number and a cooling air supply temperature of 811 K (1000 F). The first three cooling methods involve film cooling from slots. Counterflow and parallel flow describe the direction of convection cooling air along the inside surface of the wall relative to the main gas flow direction. The importance of utilizing the heat sink available in the coolant for convection cooling prior to film injection is illustrated.
Download or read book Effect of Diameter of Closed end Coolant Passages on Natural convection Water Cooling of Gas turbine Blades written by Arthur N. Curren and published by . This book was released on 1956 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental investigation on a water-cooled gas turbine with blade coolant-passage diameters ranging from 0.100 to 0.500 inch, corresponding to length-to-diameter ratios of 25.5 to 5.1, in various quadrants of the turbine. The investigation was conducted to determine (1) whether coolant-passage length-to-ratio has a significant effect on natural-convection heat-transfer correlation, and (2) whether turbine blade temperatures could be calculated with reasonable accuracy from a theoretical natural-convection heat-transfer correlation.
