Download or read book HCCI Load Expansion Opportunities Using a Fully Variable HVA Research Engine to Guide Development of a Production Intent Cam based VVA Engine written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: While the potential emissions and efficiency benefits of HCCI combustion are well known, realizing the potentials on a production intent engine presents numerous challenges. In this study we focus on identifying challenges and opportunities associated with a production intent cam-based variable valve actuation (VVA) system on a multi-cylinder engine in comparison to a fully flexible, naturally aspirated, hydraulic valve actuation (HVA) system on a single-cylinder engine, with both platforms sharing the same GDI fueling system and engine geometry. The multi-cylinder production intent VVA system uses a 2-step cam technology with wide authority cam phasing, allowing adjustments to be made to the negative valve overlap (NVO) duration but not the valve opening durations. On the single cylinder HVA engine, the valve opening duration and lift are variable in addition to the NVO duration. The content of this paper is limited to the low-medium operating load region at 2000rpm. Using different injection strategies, including the NVO pilot injection approach, the single-cylinder engine is operated over a load range from 160-390 kPa net IMEP at 2000 rpm. Changes to valve opening duration on the single-cylinder HVA engine illustrate opportunities for load expansion and efficiency improvement at certain conditions. For instance, the low load limit can be extended on the HVA engine by reducing breathing and operating closer to a stoichiometric air fuel ratio (AFR) by using valve deactivation. The naturally aspirated engine used here without external EGR confirmed that as operating load increases the emissions of NOx increases due to combustion temperature. NOx emissions are found to be one limitation to the maximum load limitation, the other being high pressure rise rate. It is found that the configuration of the production intent cam-based system represents a good compromise between valve lift and duration in the low to medium load region. Changing the extent of charge motion and breathing via valve deactivation prove beneficial at moderating the pressure rise rate and combustion stability and extending the low load limit at 2000rpm on the HVA engine. It also confirms that strategies using a pilot fuel injection are beneficial at low operating loads but that as operating load is increased, the benefits of multiple injection diminish to the point where a single injection offers the best performance.
Download or read book Proceedings of the 2nd Conference on Engine Processes written by Sens, Marc and published by Universitätsverlag der TU Berlin. This book was released on 2015-10-30 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the combustion engine looks set to remain the dominant energy conversion unit in vehicle powertrains in the medium term, either in combination with electrical components or on its own, attention will need to be paid to continue improving its efficiency in the future. The high development depth of today's combustion engines means that it is becoming increasingly difficult to achieve significant efficiency improvements by simple means. On the search for these improvements, the focus has shifted to inner-engine processes, for instance charge cycles including the charging system, the mixture formation including injection, combustion and kinematic conversion of the energy within the fuel. Our 2nd conference 'Engine processes' aims to offer all developers a platform to discuss the latest technological developments in the field of inner-engine process control, and encourage new paths to be taken. We believe that the program for this conference is a sound foundation for this endeavour. Da der Verbrennungsmotor auch mittelfristig die dominierende Energiewandlungseinheit im Antriebsstrang von Kraftfahrzeugen sein wird, entweder im Verbund mit elektrischen Komponenten oder aber als alleiniger Antrieb, muss der Verbesserung von dessen Wirkungsgrad auch in Zukunft erhebliche Aufmerksamkeit zu Teil werden. Aufgrund der hohen Entwicklungstiefe, die heutige Verbrennungsmotoren aufweisen, wird es immer schwerer, deutliche Wirkungsgradverbesserungen auf einfachem Weg zu erreichen. Auf der Suche nach diesen Verbesserungen rücken die innermotorischen Prozesse immer mehr in den Fokus, hierzu zählen der Ladungswechsel inkl. Aufladesystem, die Gemischbildung inkl. Einspritzung, die Verbrennung sowie die kinematische Wandlung der im Kraftstoff gebundenen Energie. Unsere 2. Tagung „Motorische Prozesse“ soll nun allen Entwicklern als Austauschforum zu neuesten technologischen Entwicklungen auf dem Gebiet der innermotorischen Prozessführung dienen und dazu anregen neue Wege zu beschreiten. Wir sind überzeugt, mit dem vorliegenden Tagungs-Programm hierzu einen sehr guten Beitrag leisten zu können.
Download or read book Cost Effectiveness and Deployment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2015-09-28 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt: The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.
Download or read book Engine Testing written by A. J. Martyr and published by Elsevier. This book was released on 2012-04-18 with total page 601 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engine Testing is a unique, well-organized and comprehensive collection of the different aspects of engine and vehicle testing equipment and infrastructure for anyone involved in facility design and management, physical testing and the maintenance, upgrading and trouble shooting of testing equipment. Designed so that its chapters can all stand alone to be read in sequence or out of order as needed, Engine Testing is also an ideal resource for automotive engineers required to perform testing functions whose jobs do not involve engine testing on a regular basis. This recognized standard reference for the subject is now enhanced with new chapters on hybrid testing, OBD (on-board diagnostics) and sensor signals from modern engines. One of few books dedicated to engine testing and a true, recognized market-leader on the subject Covers all key aspects of this large topic, including test-cell design and setup, data management, and dynamometer selection and use, with new chapters on hybrid testing, OBD (on-board diagnostics) and sensor signals from modern engines Brings together otherwise scattered information on the theory and practice of engine testing into one up-to-date reference for automotive engineers who must refer to such knowledge on a daily basis
Download or read book Homogeneous Charge Compression Ignition HCCI Engines written by Fuquan Zhao and published by SAE International. This book was released on 2003-01-01 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: The homogeneous charge, compression-ignition (HCCI) combustion process has the potential to significantly reduce NOx and particulate emissions, while achieving high thermal efficiency and the capability of operating with a wide variety of fuels. This makes the HCCI engine an attractive technology that can ostensibly provide diesel-like fuel efficiency and very low emissions, which may allow emissions compliance to occur without relying on lean aftertreatment systems. A profound increase in the level of research and development of this technology has occurred in the last decade. This book gathers contributions from experts in both industry and academia, providing a basic introduction to the state-of-the-art of HCCI technology, a critical review of current HCCI research and development efforts, and perspective for the future. Chapters cover: Gasoline-Fueled HCCI Engines; Diesel-Fueled HCCI Engines; Alternative Fuels and Fuel Additives for HCCI Engines; HCCI Control and Operating Range Extension; Kinetics of HCCI Combustion; HCCI Engine Modeling Approaches.In addition to the extensive overview of terminology, physical processes, and future needs, each chapter also features select SAE papers (a total of 41 are included in the book), as well as a comprehensive list of references related to the subjects. Homogeneous Charge Compression Ignition (HCCI) Engines: Key Research and Development Issues provides a valuable base of information for those interested in learning about this rapidly-progressing technology which has the potential to enhance fuel economy and reduce emissions.
Download or read book Transitions to Alternative Vehicles and Fuels written by National Research Council and published by National Academies Press. This book was released on 2013-04-14 with total page 395 pages. Available in PDF, EPUB and Kindle. Book excerpt: For a century, almost all light-duty vehicles (LDVs) have been powered by internal combustion engines operating on petroleum fuels. Energy security concerns about petroleum imports and the effect of greenhouse gas (GHG) emissions on global climate are driving interest in alternatives. Transitions to Alternative Vehicles and Fuels assesses the potential for reducing petroleum consumption and GHG emissions by 80 percent across the U.S. LDV fleet by 2050, relative to 2005. This report examines the current capability and estimated future performance and costs for each vehicle type and non-petroleum-based fuel technology as options that could significantly contribute to these goals. By analyzing scenarios that combine various fuel and vehicle pathways, the report also identifies barriers to implementation of these technologies and suggests policies to achieve the desired reductions. Several scenarios are promising, but strong, and effective policies such as research and development, subsidies, energy taxes, or regulations will be necessary to overcome barriers, such as cost and consumer choice.
Download or read book HCCI and CAI Engines for the Automotive Industry written by Hua Zhao and published by CRC Press. This book was released on 2007-09-10 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.
Download or read book Advanced Direct Injection Combustion Engine Technologies and Development written by H Zhao and published by Elsevier. This book was released on 2014-01-23 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: Direct injection enables precise control of the fuel/air mixture so that engines can be tuned for improved power and fuel economy, but ongoing research challenges remain in improving the technology for commercial applications. As fuel prices escalate DI engines are expected to gain in popularity for automotive applications. This important book, in two volumes, reviews the science and technology of different types of DI combustion engines and their fuels. Volume 1 deals with direct injection gasoline and CNG engines, including history and essential principles, approaches to improved fuel economy, design, optimisation, optical techniques and their applications. Reviews key technologies for enhancing direct injection (DI) gasoline engines Examines approaches to improved fuel economy and lower emissions Discusses DI compressed natural gas (CNG) engines and biofuels
Download or read book Engine Testing written by A. J. Martyr and published by Butterworth-Heinemann. This book was released on 2020-10-29 with total page 742 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engine Testing: Electrical, Hybrid, IC Engine and Power Storage Testing and Test Facilities, Fifth Edition covers the requirements of test facilities dealing with e-vehicle systems and different configurations and operations. Chapters dealing with the rigging and operation of Units Under Test (UUT) are updated to include electric motor-based systems, test cell services and thermo-dynamics. Control module and system testing using advanced, in-the-Loop (XiL) methods are described, including powertrain component integrated simulation and testing. All other chapters dealing with test cell design, installation, safety and use together with the cell support systems in IC engine testing are updated to reflect current developments and research. Covers multiple technical disciplines for anyone required to design, modify or operate an automotive powertrain test facility Provides tactics on the development of electrical and hybrid powertrains and energy storage systems Presents coverage of the housing and testing of automotive battery systems in addition to the use of 'virtual' testing in the form of "x-in-the-loop' throughout the powertrain's development and test life
Download or read book Calculations in Furnace Technology written by Clive Davies and published by Elsevier. This book was released on 2016-05-13 with total page 287 pages. Available in PDF, EPUB and Kindle. Book excerpt: Calculations in Furnace Technology presents the theoretical and practical aspects of furnace technology. This book provides information pertinent to the development, application, and efficiency of furnace technology. Organized into eight chapters, this book begins with an overview of the exothermic reactions that occur when carbon, hydrogen, and sulfur are burned to release the energy available in the fuel. This text then evaluates the efficiencies to measure the quantity of fuel used, of flue gases leaving the plant, of air entering, and the heat lost to the surroundings. Other chapters consider that it is important to determine the amount of carbon discharged with the ashes, the quantity and composition of any tar produced, so that a carbon balance can be applied. The final chapter describes the various reactions within the furnace atmosphere and between charges and atmosphere. This book is a valuable resource for fuel technologists, heating and ventilating engineers, and plant operators.
Download or read book SI Combustion written by and published by . This book was released on 2003 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Engine Testing written by A. J. Martyr and published by Elsevier. This book was released on 2011-04-08 with total page 459 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book brings together the large and scattered body of information on the theory and practice of engine testing, to which any engineer responsible for work of this kind must have access. Engine testing is a fundamental part of development of new engine and powertrain systems, as well as of the modification of existing systems. It forms a significant part of the practical work of many automotive and mechanical engineers, in the auto manufacturing companies, their suppliers suppliers, specialist engineering services organisations, the motor sport sector, hybrid vehicles and tuning sector. The eclectic nature of engine, powertrain, chassis and whole vehicle testing makes this comprehensive book a true must-have reference for those in the automotive industry as well as more advanced students of automotive engineering. * The only book dedicated to engine testing; over 4000 copies sold of the second edition* Covers all key aspects of this large topic, including test-cell set up, data management, dynamometer selection and use, air, thermal, combustion, mechanical, and emissions assessment* Most automotive engineers are involved with many aspects covered by this book, making it a must-have reference
Download or read book Hydrogen and Fuel Cells written by International Energy Agency and published by Simon and Schuster. This book was released on 2004 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydrogen and fuel cells are vital technologies to ensure a secure and CO2-free energy future. Their development will take decades of extensive public and private effort to achieve technology breakthroughs and commercial maturity. Government research programs are indispensable for catalyzing the development process. This report maps the IEA countries' current efforts to research, develop and deploy the interlocking elements that constitute a "hydrogen economy", including CO2 capture and storage when hydrogen is produced out of fossil fuels. It provides an overview of what is being done, and by whom, covering an extensive complexity of national government R & D programs. The survey highlights the potential for exploiting the benefits of the international cooperation. This book draws primarily upon information contributed by IEA governments. In virtually all the IEA countries, important R & D and policy efforts on hydrogen and fuel cells are in place and expanding. Some are fully-integrated, government-funded programs, some are a key element in an overall strategy spread among multiple public and private efforts. The large amount of information provided in this publication reflects the vast array of technologies and logistics required to build the "hydrogen economy."--Publisher description.
Download or read book Fuels and Lubricants Handbook written by and published by . This book was released on 2003 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Theory Of Superconductivity written by J. Robert Schrieffer and published by CRC Press. This book was released on 2018-03-05 with total page 352 pages. Available in PDF, EPUB and Kindle. Book excerpt: Theory of Superconductivity is primarily intended to serve as a background for reading the literature in which detailed applications of the microscopic theory of superconductivity are made to specific problems.
Download or read book Vehicle Sensors and Actuators written by and published by . This book was released on 2005 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book CESAR Cost efficient Methods and Processes for Safety relevant Embedded Systems written by Ajitha Rajan and published by Springer Science & Business Media. This book was released on 2013-03-25 with total page 403 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book summarizes the findings and contributions of the European ARTEMIS project, CESAR, for improving and enabling interoperability of methods, tools, and processes to meet the demands in embedded systems development across four domains - avionics, automotive, automation, and rail. The contributions give insight to an improved engineering and safety process life-cycle for the development of safety critical systems. They present new concept of engineering tools integration platform to improve the development of safety critical embedded systems and illustrate capacity of this framework for end-user instantiation to specific domain needs and processes. They also advance state-of-the-art in component-based development as well as component and system validation and verification, with tool support. And finally they describe industry relevant evaluated processes and methods especially designed for the embedded systems sector as well as easy adoptable common interoperability principles for software tool integration.
