Download or read book Thermal Management and Control of a Homogeneous Charge Compression Ignition HCCI Engine written by George Constandinides and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book HCCI Engine Control by Thermal Management written by and published by . This book was released on 2000 with total page 33 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work investigates a control system for HCCI engines, where thermal energy from exhaust gas recirculation (EGR) and compression work in the supercharger are either recycled or rejected as needed. HCCI engine operation is analyzed with a detailed chemical kinetics code, HCT (Hydrodynamics, Chemistry and Transport), that has been extensively modified for application to engines. HCT is linked to an optimizer that determines the operating conditions that result in maximum brake thermal efficiency, while meeting the restrictions of low NO(subscript x) and peak cylinder pressure. The results show the values of the operating conditions that yield optimum efficiency as a function of torque and RPM. For zero torque (idle), the optimizer determines operating conditions that result in minimum fuel consumption. The optimizer is also used for determining the maximum torque that can be obtained within the operating restrictions of NO(subscript x) and peak cylinder pressure. The results show that a thermally controlled HCCI engine can successfully operate over a wide range of conditions at high efficiency and low emissions.

Download or read book Closed Loop Combustion Control of a Multi Cylinder HCCI Engine Using Variable Compression Ratio and Fast Thermal Management written by Göran Haraldsson and published by . This book was released on 2005 with total page 65 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Closed loop Control of a Multicylinder Homogeneous Charge Compression Ignition Engine Using Fast Thermal Management and Ion Sensors written by Parag Mehresh and published by . This book was released on 2005 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hcci and Cai Engines for the Automotive Industry written by H Zhao and published by Elsevier. This book was released on 2007-08-02 with total page 557 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality.HCCI and CAI engines for the automotive industry presents the state-of-the-art in research and development on an international basis, as a one-stop reference work. The background to the development of HCCI / CAI engine technology is described. Basic principles, the technologies and their potential applications, strengths and weaknesses, as well as likely future trends and sources of further information are reviewed in the areas of gasoline HCCI / CAI engines; diesel HCCI engines; HCCI / CAI engines with alternative fuels; and advanced modelling and experimental techniques. The book provides an invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide. Presents the state-of-the-art in research and development on an international basis An invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide Looks at one of the most promising engine technologies around

Download or read book The Performance of a Multi Cylinder HCCI Engine Using Variable Compression Ratio and Fast Thermal Management written by Jari Hyvönen and published by . This book was released on 2005 with total page 93 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Cost Effectiveness and Deployment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2015-09-28 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt: The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.

Download or read book Thermal Management in Automotive Applications written by T Yomi Obidi and published by SAE International. This book was released on 2015-03-30 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: With new and more stringent standards addressing emission reduction and fuel economy, the importance of a well-developed engine thermal management system becomes even greater. With about 30% of the fuel intake energy dissipated through the cooling system and another 30% through the exhaust system, it is to be expected that serious research has been dedicated to this field. Thermal Management in Automotive Applications, edited by Dr. T. Yomi Obidi, brings together a focused collection of SAE technical papers on the subject. It offers insights into how thermal management impacts the efficiency of engines in heavy vehicles, the effects of better coolant flow control, and the use of smart thermostat and next-generation cooling pumps. It also provides an in-depth analysis of the possible gains in optimum warm-up sequence and thermal management on a small gasoline engine. With continuously increasing gadgetry in modern vehicles, the average temperature in the engine compartment has seen significant increase. It is important to be able to divert the heat away from passengers as well as from some components that may be negatively impacted by excessive temperatures. Thermal Management in Automotive Applications points out solutions to this challenge, including material and design options.

Download or read book Characteristics and Control of Low Temperature Combustion Engines written by Rakesh Kumar Maurya and published by Springer. This book was released on 2017-11-03 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with novel advanced engine combustion technologies having potential of high fuel conversion efficiency along with ultralow NOx and particulate matter (PM) emissions. It offers insight into advanced combustion modes for efficient utilization of gasoline like fuels. Fundamentals of various advanced low temperature combustion (LTC) systems such as HCCI, PCCI, PPC and RCCI engines and their fuel quality requirements are also discussed. Detailed performance, combustion and emissions characteristics of futuristic engine technologies such as PPC and RCCI employing conventional as well as alternative fuels are analyzed and discussed. Special emphasis is placed on soot particle number emission characterization, high load limiting constraints, and fuel effects on combustion characteristics in LTC engines. For closed loop combustion control of LTC engines, sensors, actuators and control strategies are also discussed. The book should prove useful to a broad audience, including graduate students, researchers, and professionals Offers novel technologies for improved and efficient utilization of gasoline like fuels; Deals with most advanced and futuristic engine combustion modes such as PPC and RCCI; Comprehensible presentation of the performance, combustion and emissions characteristics of low temperature combustion (LTC) engines; Deals with closed loop combustion control of advanced LTC engines; State-of-the-art technology book that concisely summarizes the recent advancements in LTC technology. .

Download or read book Handbook of Thermal Management of Engines written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on 2022-01-01 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook deals with the vast subject of thermal management of engines and vehicles by applying the state of the art research to diesel and natural gas engines. The contributions from global experts focus on management, generation, and retention of heat in after-treatment and exhaust systems for light-off of NOx, PM, and PN catalysts during cold start and city cycles as well as operation at ultralow temperatures. This book will be of great interest to those in academia and industry involved in the design and development of advanced diesel and CNG engines satisfying the current and future emission standards.

Download or read book HCCI and CAI Engines for the Automotive Industry written by Hua Zhao and published by CRC Press. This book was released on 2007-09-10 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.

Download or read book DI HCCI Engine Control System Development written by Kushal Narayanaswamy and published by . This book was released on 2006 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Vehicle Thermal Management written by Gursaran D Mathur and published by SAE International. This book was released on 2004-04-08 with total page 397 pages. Available in PDF, EPUB and Kindle. Book excerpt: The efficiency of thermal systems (HVAC, engine cooling, transmission, and power steering) has improved greatly over the past few years. Operating these systems typically requires a significant amount of energy, however, which could adversely affect vehicle performance. To provide customers the level of comfort that they demand in an energy-efficient manner, innovative approaches must be developed. Vehicle Thermal Management: Heat Exchangers & Climate Control is an essential resource for engineers and designers working on thermal systems, presenting the most recent and relevant technical papers that focus on this important vehicle component. Chapters include: Heating and Air Conditioning Engine Cooling Underhood Thermal Environment Heat Transfer in Engines Heat Exchangers New Technologies

Download or read book Thermal Barrier for Homogeneous Charge Compression Ignition Application written by Edward Lawrence Hurley and published by . This book was released on 2010 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stringent emissions regulations set forth by the Environmental Protection Agency has forced the automotive industry in the United States to seek a low cost and reliable solution to meet these regulations. Homogeneous Charge Compression Ignition (HCCI) is one of the potential answers to the problem. The HCCI combustion process mates the best features of the two main Internal Combustion Engines (ICE) technologies, Spark Ignition (SI) and Compression Ignition Direct Injected (CIDI). The HCCI combustion process is building on the advantages of each technology while avoiding the disadvantages. One of the main hurdles preventing the successful application of an HCCI engine to the main automotive market is the lack of the precise control over the combustion event. Every successful HCCI research engine found during the literature review employed an external energy source to provide the energy boost necessary for the combustion event. The work contained in this thesis was designed to capture the energy normally wasted by the engine through the engine's exhaust and cooling systems with a Thermal Barrier Coating (TBC). The captured energy was used as the energy boost necessary to cause and control HCCI combustion. This was achieved by modifying a Nissan gasoline engine by increasing the compression ratio from 10.3:1 to 13.5:1 along with coating the cylinder head fire deck, valve heads and crown of the pistons with TBC.

Download or read book Modeling and Analysis of an HCCI Engine During Thermal Transients Using a Thermodynamic Cycle Simulation with a Coupled Wall Thermal Network written by Kyoungjoon Chang and published by . This book was released on 2006 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Functional Reverse Engineering of Strategic and Non Strategic Machine Tools written by Wasim Ahmed Khan and published by CRC Press. This book was released on 2021-06-20 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes capacity building in strategic and non-strategic machine tool technology. It includes machine building in sectors such as machine tools, automobiles, home appliances, energy, and biomedical engineering, along with case studies. The book offers guidelines for capacity building in academia, covering how to promote enterprises of functional reverse engineering enterprises. It also discusses machine tool development, engineering design, prototyping of strategic, and non-strategies machine tools, as well as presenting communication strategies and IoT, along with case studies. Professionals from the CNC (Computer Numeric Control) machine tools industry, industrial and manufacturing engineers, and students and faculty in engineering disciplines will find interest in this book.

Download or read book Control and Robustness Analysis of Homogeneous Charge Compression Ignition Using Exhaust Recompression written by Hsien-Hsin Liao and published by Stanford University. This book was released on 2011 with total page 201 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been an enormous global research effort to alleviate the current and projected environmental consequences incurred by internal combustion (IC) engines, the dominant propulsion systems in ground vehicles. Two technologies have the potential to improve the efficiency and emissions of IC engines in the near future: variable valve actuation (VVA) and homogeneous charge compression ignition (HCCI). IC engines equipped with VVA systems are proven to show better performance by adjusting the valve lift and timing appropriately. An electro-hydraulic valve system (EHVS) is a type of VVA system that possesses full flexibility, i.e., the ability to change the valve lift and timing independently and continuously, making it an ideal rapid prototyping tool in a research environment. Unfortunately, an EHVS typically shows a significant response time delay that limits the achievable closed-loop bandwidth and, as a result, shows poor tracking performance. In this thesis, a control framework that includes system identification, feedback control design, and repetitive control design is presented. The combined control law shows excellent performance with a root-mean-square tracking error below 40 [Mu]m over a maximum valve lift of 4 mm. A stability analysis is also provided to show that the mean tracking error converges to zero asymptotically with the combined control law. HCCI, the other technology presented in this thesis, is a combustion strategy initiated by compressing a homogeneous air-fuel mixture to auto-ignition, therefore, ignition occurs at multiple points inside the cylinder without noticeable flame propagation. The result is rapid combustion with low peak in-cylinder temperature, which gives HCCI improved efficiency and reduces NOx formation. To initiate HCCI with a typical compression ratio, the sensible energy of the mixture needs to be high compared to a spark ignited (SI) strategy. One approach to achieve this, called recompression HCCI, is by closing the exhaust valve early to trap a portion of the exhaust gas in the cylinder. Unlike a SI or Diesel strategy, HCCI lacks an explicit combustion trigger, as autoignition is governed by chemical kinetics. Therefore, the thermo-chemical conditions of the air-fuel mixture need to be carefully controlled for HCCI to occur at the desired timing. Compounding this challenge in recompression HCCI is the re-utilization of the exhaust gas which creates cycle-to-cycle coupling. Furthermore, the coupling characteristics can change drastically around different operating points, making combustion timing control difficult across a wide range of conditions. In this thesis, a graphical analysis examines the in-cylinder temperature dynamics of recompression HCCI and reveals three qualitative types of temperature dynamics. With this insight, a switching linear model is formulated by combining three linear models: one for each of the three types of temperature dynamics. A switching controller that is composed of three local linear feedback controllers can then be designed based on the switching model. This switching model/control formulation is tested on an experimental HCCI testbed and shows good performance in controlling the combustion timing across a wide range. A semi-definite program is formulated to find a Lyapunov function for the switching model/control framework and shows that it is stable. As HCCI is dictated by the in-cylinder thermo-chemical conditions, there are further concerns about the robustness of HCCI, i.e., the boundedness of the thermo-chemical conditions with uncertainty existing in the ambient conditions and in the engine's own characteristics due to aging. To assess HCCI's robustness, this thesis presents a linear parameter varying (LPV) model that captures the dynamics of recompression HCCI and possesses an elegant model structure that is more amenable to analysis. Based on this model, a recursive algorithm using convex optimization is formulated to generate analytical statements about the boundedness of the in-cylinder thermo-chemical conditions. The bounds generated by the algorithm are also shown to relate well to the data from the experimental testbed.