Download or read book Generation and Computerized Simulation of Meshing and Contact of Modified Involute Helical Gears written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-07 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt: The design and generation of modified involute helical gears that have a localized and stable bearing contact, and reduced noise and vibration characteristics are described. The localization of the bearing contact is achieved by the mismatch of the two generating surfaces that are used for generation of the pinion and the gear. The reduction of noise and vibration will be achieved by application of a parabolic function of transmission errors that is able to absorb the almost linear function of transmission errors caused by gear misalignment. The meshing and contact of misaligned gear drives can be analyzed by application of computer programs that have been developed. The computations confirmed the effectiveness of the proposed modification of the gear geometry. A numerical example that illustrates the developed theory is provided. Litvin, Faydor L. and Chen, Ningxin and Lu, Jian Unspecified Center...
Download or read book Computerized Generation and Simulation of Meshing of Modified Spur and Helical Gears Manufactured by Shaving written by and published by . This book was released on 2001 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modification of geometry of spur and helical gears with parallel axes and helical gears with crossed axes is proposed. The finishing process of gear generation is shaving. The purposes of modification of the gear geometry are to localize and stabilize the bearing contact, and to reduce noise and vibration. The goals mentioned above are achieved by using profile crowning and plunging the shaver by a prescribed motion during pinion generation. The pinion becomes double crowned. The gear member is generated as a conventional involute gear. A tooth contact analysis (TCA) program for simulation of meshing and contact was developed and the analysis is illustrated with TCA results for spur and helical gears.
Download or read book Generation and Computerized Simulation of Meshing and Contact of Modified Involute Helical Gears written by Faydor L. Litvin and published by . This book was released on 1995 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Generation and Computerized Simulation of Meshing and Contact of Modified Involute Helical Gears written by Faydor L. Litvin and published by . This book was released on 1995 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Computerized Generation and Simulation of Meshing and Contact of New Type of Novikov Wildhaber Helical Gears written by and published by . This book was released on 2000 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this report, we propose a new geometry for low-noise, increased-strength helical gears of the Novikov- Wildhaber type. Contact stresses are reduced as a result of their convex-concave gear tooth surfaces. The gear tooth surfaces are crowned in the profile direction to localize bearing contact and in the longitudinal direction to obtain a parabolic function of transmission errors. Such a function results in the reduction of noise and vibrations. Methods for the generation of the proposed gear tooth surfaces by grinding and hobbing are considered, and a tooth contact analysis (TCA) computer program to simulate meshing and contact is applied. The report also investigates the influence of misalignment on transmission errors and shift of bearing contact. Numerical examples to illustrate the developed approaches are proposed.
Download or read book Modified Involute Helical Gears written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-03 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of alignment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.Glenn Research CenterCOMPUTER AIDED DESIGN; GEARS; STRESS ANALYSIS; COMPUTERIZED SIMULATION; VIBRATION
Download or read book Gear Geometry and Applied Theory written by Faydor L. Litvin and published by Cambridge University Press. This book was released on 2004-09-06 with total page 820 pages. Available in PDF, EPUB and Kindle. Book excerpt: This revised, expanded, edition covers the theory, design, geometry and manufacture of all types of gears and gear drives. This is an invaluable reference for designers, theoreticians, students, and manufacturers. This edition includes advances in gear theory, gear manufacturing, and computer simulation. Among the new topics are: 1. New geometry for modified spur and helical gears, face-gear drives, and cycloidal pumps. 2. New design approaches for one stage planetary gear trains and spiral bevel gear drives. 3. An enhanced approach for stress analysis of gear drives with FEM. 4. New methods of grinding face gear drives, generating double crowned pinions, and improved helical gear shaving. 5. Broad application of simulation of meshing and TCA. 6. New theories on the simulation of meshing for multi-body systems, detection of cases wherein the contact line on generating surfaces may have its own envelope, and detection and avoidance of singularities of generated surfaces.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 538 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
Download or read book Novikov Conformal Gearing written by Stephen P. Radzevich and published by Springer Nature. This book was released on 2022-11-14 with total page 485 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the latest accomplishments in Novikov/conformal gearing as well as high-conformal gearing. It is focused primarily on strength calculation of gear teeth and the manufacturing of gears for Novikov/conformal and high-conformal gearing along with a brief discussion of achievements in the modern theory of gearing. The modern theory of gearing is the foundation of all optimal designs of gears, gear-sets, and transmissions of all known designs, as well as, of all those to be developed in the future. As even a small improvement in efficiency on a single gear can represent a significant cost saving, given the millions of gears used in industry every year, this volume provides the design and manufacturing engineer in invaluable resource.
Download or read book Modified Involute Helical Gears Computerized Design Simulation of Meshing and Stress Analysis written by and published by . This book was released on 2003 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of alignment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.
Download or read book Computerized Simulation of Meshing of Conventional Helical Involute Gears and Modification of Geometry written by and published by . This book was released on 1997 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: An approach is proposed for computerized simulation of meshing of aligned and misaligned involute helical gears. Algorithms for TCA (Tooth Contact Analysis) computer programs were developed. Influence of misalignment on the shift of the bearing contact and transmission errors has been investigated. Numerical examples that illustrate the developed theory are provided.
Download or read book High Conformal Gearing written by Stephen Radzevich and published by Elsevier. This book was released on 2020-07-04 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: The new edition of High-Conformal Gearing continues to address the kinematics and the geometry of conformal (Novikov) gearing and high-conformal gearing. The book deals with gears that feature convex-to-concave contact of the tooth flanks of a gear and a mating pinion. Gears of this type are commonly referred to as conformal gearings. Novikov gearing is the most widely known example of conformal gearing. The helical gearing by Wildhaber, Bramley-Moore (otherwise known as the Vivkers, Bostock, and Bramley gearing, or just V.B.B.-gearing), are well-known designs of gearing that are loosely referred to as conformal gearing. The principal differences between conformal gearing as well as high-conformal gearing and Wildhaber helical gearing are outlined. It also shows that Wildhaber helical gearing from one side, and Novikov gearing from another side, are two completely different gear systems that cannot be combined into a common gear system. This book aids mechanical, automotive, and robotics engineers specializing in gear design with successfully transmitting a rotation. It also serves as a resource for graduate students taking advanced courses in gear design. - Discusses the kinematics and geometry of conformal and high-conformal gearing - Provides a specific set of conditions which need to be met when designing conformal and high-conformal gears - Outlines the principal differences between conformal, high-conformal and Wildhaber helical gearing
Download or read book Gear Geometry and Applied Theory written by Faydor L. Litvin and published by Cambridge University Press. This book was released on 2004-09-06 with total page 818 pages. Available in PDF, EPUB and Kindle. Book excerpt: This revised, expanded edition covers the theory, design, geometry, and manufacture of all types of gears and gear drives. An invaluable reference for designers, theoreticians, students, and manufacturers, the second edition includes advances in gear theory, gear manufacturing, and computer simulation. Among the new topics are: new geometry for gears and pumps; new design approaches for planetary gear trains and bevel gear drives; an enhanced approach for stress analysis; new methods of grinding and gear shaving; and new theory on the simulation and its application. First Edition published by Pearson Education Hb (1994): 0-132-11095-4
Download or read book Metal Cutting Theory and Practice written by David A. Stephenson and published by CRC Press. This book was released on 2018-09-03 with total page 1381 pages. Available in PDF, EPUB and Kindle. Book excerpt: A Complete Reference Covering the Latest Technology in Metal Cutting Tools, Processes, and Equipment Metal Cutting Theory and Practice, Third Edition shapes the future of material removal in new and lasting ways. Centered on metallic work materials and traditional chip-forming cutting methods, the book provides a physical understanding of conventional and high-speed machining processes applied to metallic work pieces, and serves as a basis for effective process design and troubleshooting. This latest edition of a well-known reference highlights recent developments, covers the latest research results, and reflects current areas of emphasis in industrial practice. Based on the authors’ extensive automotive production experience, it covers several structural changes, and includes an extensive review of computer aided engineering (CAE) methods for process analysis and design. Providing updated material throughout, it offers insight and understanding to engineers looking to design, operate, troubleshoot, and improve high quality, cost effective metal cutting operations. The book contains extensive up-to-date references to both scientific and trade literature, and provides a description of error mapping and compensation strategies for CNC machines based on recently issued international standards, and includes chapters on cutting fluids and gear machining. The authors also offer updated information on tooling grades and practices for machining compacted graphite iron, nickel alloys, and other hard-to-machine materials, as well as a full description of minimum quantity lubrication systems, tooling, and processing practices. In addition, updated topics include machine tool types and structures, cutting tool materials and coatings, cutting mechanics and temperatures, process simulation and analysis, and tool wear from both chemical and mechanical viewpoints. Comprised of 17 chapters, this detailed study: Describes the common machining operations used to produce specific shapes or surface characteristics Contains conventional and advanced cutting tool technologies Explains the properties and characteristics of tools which influence tool design or selection Clarifies the physical mechanisms which lead to tool failure and identifies general strategies for reducing failure rates and increasing tool life Includes common machinability criteria, tests, and indices Breaks down the economics of machining operations Offers an overview of the engineering aspects of MQL machining Summarizes gear machining and finishing methods for common gear types, and more Metal Cutting Theory and Practice, Third Edition emphasizes the physical understanding and analysis for robust process design, troubleshooting, and improvement, and aids manufacturing engineering professionals, and engineering students in manufacturing engineering and machining processes programs.
Download or read book Global Design to Gain a Competitive Edge written by Xiu-Tian Yan and published by Springer Science & Business Media. This book was released on 2008-07-30 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent rapid globalisation of manufacturing industries leads to a drive and thirst for rapid advancements in technological development and expertise in the fields of advanced design and manufacturing, especially at their interfaces. This development results in many economical benefits to and improvement of quality of life for many people all over the world. Technically speaking, this rapid development also create many opportunities and challenges for both industrialists and academics, as the design requirements and constraints have completely changed in this global design and manufacture environment. Consequently the way to design, manufacture and realise products have changed as well. The days of designing for a local market and using local suppliers in manufacturing have gone, if enterprises aim to maintain their competitiveness and global expansion leading to further success. In this global context and scenario, both industry and the academia have an urgent need to equip themselves with the latest knowledge, technology and methods developed for engineering design and manufacture. To address this shift in engineering design and manufacture, supported by the European Commission under the Asia Link Programme with a project title FASTAHEAD (A Framework Approach to Strengthening Asian Higher Education in Advanced Design and Manufacture), three key project partners, namely the University of Strathclyde of the United Kingdom, Northwestern Polytechncial University of China, and the Troyes University of Technology of France organised a third international conference.
Download or read book Development of Gear Technology and Theory of Gearing written by Faydor L. Litvin and published by . This book was released on 1997 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents recent developments in the theory of gearing and the modifications in gear geometry necessary to improve the conditions of meshing. Highlighted are low-noise gear drives that have a stable contact during meshing and a predesigned parabolic transmission error function that can handle misalignment during operation without sacrificing the low-noise aspects of operation. This book also provides a comprehensive history of the develoment of the theory of gearing through biographies of major contributors to this field. The author's unique historical perspective was achieved by assiduous research into the lives of courageous, talented, and creative men who made significant contributions to the field of gearing.
Download or read book Theory and Practice of Gearing and Transmissions written by Veniamin Goldfarb and published by Springer. This book was released on 2015-08-26 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book brings together papers from all spheres of mechanical engineering related to gears and transmissions, from fundamentals to advanced applications, from academic results in numerical and experimental research, to new approaches to gear design and aspects of their optimization synthesis and to the latest developments in manufacturing. Furthermore, this volume honours the work of Faydor L. Litvin on the 100th anniversary of this birth. He is acknowledged as the founder of the modern theory of gearing. An exhaustive list of his contributions and achievements and a biography are included.