Download or read book Gas Turbines Structural Properties Operation Principles and Design Features written by Kun Liu and published by Springer Nature. This book was released on 2023-05-29 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book gives a clear idea about the concept of gas turbines, thermodynamic basics of the turbine theory. It includes classification of gas turbines, working principle, structure feather, application and designing approaches of gas turbines. The readers will understand easily the power system for ships since there are a lot illustrations and instruction for each of equipment. It also introduces the thermal calculation of gas turbine unit, different structure feather of compressor, combustion chamber and turbine. It gives the way to increases the efficiency of the unit, design and operation of the gas turbine parts. The combined marine power plant with gas turbine is discussed and advantages and disadvantages for each type unit is discussed too.
Download or read book The Gas Turbine Handbook written by Tony Giampaolo and published by The Fairmont Press, Inc.. This book was released on 2003 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of a bestseller, this comprehensive reference provides the fundamental information required to understand both the operation and proper application of all types of gas turbines. The completely updated second edition adds a new section on use of inlet cooling for power augmentation and NOx control. It explores the full spectrum of gas turbines hardware, typical application scenarios, and operating parameters, controls, inlet treatments, inspection, trouble-shooting, and more. The author discusses strategies that can help readers avoid problems before they occur and provides tips that enable diagnosis of problems in their early stages and analysis of failures to prevent their recurrence.
Download or read book Gas Turbine Handbook written by Tony Giampaolo and published by CRC Press. This book was released on 2020-11-26 with total page 475 pages. Available in PDF, EPUB and Kindle. Book excerpt: Newly revised, this new fifth edition includes a chapter on waste heat recovery and discusses this technology in detail including a the advantages and barriers to waste heat recovery, environmental restraints, thermodynamics of heat recovery, fluid properties, boiler, condensers, steam turbines, off design behavior and exhaust catalyst. This book shows how microturbine designs rely heavily on the centrifugal compressor and are, in many aspects, similar to the early flight engines and will illustrate how the approach of the microturbine designer is to minimize cost.
Download or read book Materials and Strength of Gas Turbine Parts written by Leonid Borisovich Getsov and published by Springer Nature. This book was released on 2021-04-17 with total page 469 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses several mechanical and material problems that are typical for gas turbine components. It discusses accelerated tests and other methods for increasing the reliability of gas turbine engines. Special attention is given to non-traditional methods for calculating the strength characteristics and longevity of the main components. This first volume focuses on the selection of materials, deformation and destruction mechanisms in connection with stationary and non-stationary loading, and types of material damage such as the thermal fatigue. Particular attention is paid to the issues of the properties of single crystal alloys, the relationship between structure and properties, the influence of technological factors and long-term operation. The characteristics of creep resistance, crack resistance, and resistance to cyclic deformation of different alloys are given.
Download or read book The Design of High Efficiency Turbomachinery and Gas Turbines second edition with a new preface written by David Gordon Wilson and published by MIT Press. This book was released on 2014-09-12 with total page 625 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of a comprehensive textbook that introduces turbomachinery and gas turbines through design methods and examples. This comprehensive textbook is unique in its design-focused approach to turbomachinery and gas turbines. It offers students and practicing engineers methods for configuring these machines to perform with the highest possible efficiency. Examples and problems are based on the actual design of turbomachinery and turbines. After an introductory chapter that outlines the goals of the book and provides definitions of terms and parts, the book offers a brief review of the basic principles of thermodynamics and efficiency definitions. The rest of the book is devoted to the analysis and design of real turbomachinery configurations and gas turbines, based on a consistent application of thermodynamic theory and a more empirical treatment of fluid dynamics that relies on the extensive use of design charts. Topics include turbine power cycles, diffusion and diffusers, the analysis and design of three-dimensional free-stream flow, and combustion systems and combustion calculations. The second edition updates every chapter, adding material on subjects that include flow correlations, energy transfer in turbomachines, and three-dimensional design. A solutions manual is available for instructors. This new MIT Press edition makes a popular text available again, with corrections and some updates, to a wide audience of students, professors, and professionals.
Download or read book Gas Turbines written by Gurrappa Injeti and published by BoD – Books on Demand. This book was released on 2010-09-27 with total page 378 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended to provide valuable information for the analysis and design of various gas turbine engines for different applications. The target audience for this book is design, maintenance, materials, aerospace and mechanical engineers. The design and maintenance engineers in the gas turbine and aircraft industry will benefit immensely from the integration and system discussions in the book. The chapters are of high relevance and interest to manufacturers, researchers and academicians as well.
Download or read book Gas Turbines written by Claire Soares and published by Elsevier. This book was released on 2014-10-23 with total page 1021 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covering basic theory, components, installation, maintenance, manufacturing, regulation and industry developments, Gas Turbines: A Handbook of Air, Sea and Land Applications is a broad-based introductory reference designed to give you the knowledge needed to succeed in the gas turbine industry, land, sea and air applications.Providing the big picture view that other detailed, data-focused resources lack, this book has a strong focus on the information needed to effectively decision-make and plan gas turbine system use for particular applications, taking into consideration not only operational requirements but long-term life-cycle costs in upkeep, repair and future use.With concise, easily digestible overviews of all important theoretical bases and a practical focus throughout, Gas Turbines is an ideal handbook for those new to the field or in the early stages of their career, as well as more experienced engineers looking for a reliable, one-stop reference that covers the breadth of the field. - Covers installation, maintenance, manufacturer's specifications, performance criteria and future trends, offering a rounded view of the area that takes in technical detail as well as well as industry economics and outlook - Updated with the latest industry developments, including new emission and efficiency regulations and their impact on gas turbine technology - Over 300 pages of new/revised content, including new sections on microturbines, non-conventional fuel sources for microturbines, emissions, major developments in aircraft engines, use of coal gas and superheated steam, and new case histories throughout highlighting component improvements in all systems and sub-systems
Download or read book Steam and gas turbines written by Krzysztof Kosowski and published by . This book was released on 2007 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Handbook written by Tony Giampaolo and published by The Fairmont Press, Inc.. This book was released on 2009 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2017-09-01 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. - Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers - A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field - The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems
Download or read book Gas Turbine Performance written by Philip P. Walsh and published by John Wiley & Sons. This book was released on 2008-04-15 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: A significant addition to the literature on gas turbine technology, the second edition of Gas Turbine Performance is a lengthy text covering product advances and technological developments. Including extensive figures, charts, tables and formulae, this book will interest everyone concerned with gas turbine technology, whether they are designers, marketing staff or users.
Download or read book Gas Turbine Design Components and System Design Integration written by Meinhard T. Schobeiri and published by Springer. This book was released on 2017-06-06 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book written by a world-renowned expert with more than forty years of active gas turbine R&D experience comprehensively treats the design of gas turbine components and their integration into a complete system. Unlike many currently available gas turbine handbooks that provide the reader with an overview without in-depth treatment of the subject, the current book is concentrated on a detailed aero-thermodynamics, design and off-deign performance aspects of individual components as well as the system integration and its dynamic operation.This new book provides practicing gas turbine designers and young engineers working in the industry with design material that the manufacturers would keep proprietary. The book is also intended to provide instructors of turbomachinery courses around the world with a powerful tool to assign gas turbine components as project and individual modules that are integrated into a complete system. Quoting many statements by the gas turbine industry professionals, the young engineers graduated from the turbomachinery courses offered by the author, had the competency of engineers equivalent to three to four years of industrial experience.
Download or read book Gas Turbines written by Gurrappa Injeti and published by BoD – Books on Demand. This book was released on 2015-02-25 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents current research in the area of gas turbines for different applications. It is a highly useful book providing a variety of topics ranging from basic understanding about the materials and coatings selection, designing and modeling of gas turbines to advanced technologies for their ever increasing efficiency, which is the need of the hour for modern gas turbine industries. The target audience for this book is material scientists, gas turbine engine design and maintenance engineers, manufacturers, mechanical engineers, undergraduate, post graduate students and academic researchers. The design and maintenance engineers in aerospace and gas turbine industry will benefit from the contents and discussions in this book.This book presents current research in the area of gas turbines for different applications. It is a highly useful book providing a variety of topics ranging from basic understanding about the materials and coatings selection, designing and modeling of gas turbines to advanced technologies for their ever increasing efficiency, which is the need of the hour for modern gas turbine industries. The target audience for this book is material scientists, gas turbine engine design and maintenance engineers, manufacturers, mechanical engineers, undergraduate, post graduate students and academic researchers. The design and maintenance engineers in aerospace and gas turbine industry will benefit from the contents and discussions in this book.
Download or read book The Gas Turbine written by Henry Harrison Suplee and published by . This book was released on 1910 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Design Components and System Design Integration written by Meinhard T. Schobeiri and published by Springer Nature. This book was released on 2019-11-25 with total page 537 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the second revised and enhanced edition of the book Gas Turbine Design, Components and System Integration written by a world-renowned expert with more than forty years of active gas turbine R&D experience. It comprehensively treats the design of gas turbine components and their integration into a complete system. Unlike many currently available gas turbine handbooks that provide the reader with an overview without in-depth treatment of the subject, the current book is concentrated on a detailed aero-thermodynamics, design and off-deign performance aspects of individual components as well as the system integration and its dynamic operation. This new book provides practicing gas turbine designers and young engineers working in the industry with design material that the manufacturers would keep proprietary. The book is also intended to provide instructors of turbomachinery courses around the world with a powerful tool to assign gas turbine components as project and individual modules that are integrated into a complete system. Quoting many statements by the gas turbine industry professionals, the young engineers graduated from the turbomachinery courses offered by the author, had the competency of engineers equivalent to three to four years of industrial experience.
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2011-11-23 with total page 993 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by one of the field's most well known experts, the Gas Turbine Engineering Handbook has long been the standard for engineers involved in the design, selection, maintenance and operation of gas turbines. With far reaching, comprehensive coverage across a range of topics from design specifications to maintenance troubleshooting, this one-stop resource provides newcomers to the industry with all the essentials to learn and fill knowledge gaps, and established practicing gas turbine engineers with a reliable go-to reference. This new edition brings the Gas Turbine Engineering Handbook right up to date with new legislation and emerging topics to help the next generation of gas turbine professionals understand the underlying principles of gas turbine operation, the economic considerations and implications of operating these machines, and how they fit in with alternative methods of power generation. - The most comprehensive one-stop source of information on industrial gas turbines, with vital background, maintenance information, legislative details and calculations combined in an essential all-in-one reference - Written by an industry-leading consultant and trainer and suitable for use as a training companion or a reliable dip-in guide - Includes hard-won information from industry experts in the form of case histories that offer practical trouble-shooting guidance and solutions
Download or read book Industrial Gas Turbines written by A M Y Razak and published by Elsevier. This book was released on 2007-10-31 with total page 625 pages. Available in PDF, EPUB and Kindle. Book excerpt: Industrial Gas Turbines: Performance and Operability explains important aspects of gas turbine performance such as performance deterioration, service life and engine emissions. Traditionally, gas turbine performance has been taught from a design perspective with insufficient attention paid to the operational issues of a specific site. Operators are not always sufficiently familiar with engine performance issues to resolve operational problems and optimise performance.Industrial Gas Turbines: Performance and Operability discusses the key factors determining the performance of compressors, turbines, combustion and engine controls. An accompanying engine simulator CD illustrates gas turbine performance from the perspective of the operator, building on the concepts discussed in the text. The simulator is effectively a virtual engine and can be subjected to operating conditions that would be dangerous and damaging to an engine in real-life conditions. It also deals with issues of engine deterioration, emissions and turbine life. The combined use of text and simulators is designed to allow the reader to better understand and optimise gas turbine operation. - Discusses the key factors in determining the perfomance of compressors, turbines, combustion and engine controls - Explains important aspects of gas and turbine perfomance such as service life and engine emissions - Accompanied by CD illustrating gas turbine performance, building on the concepts discussed in the text