Download or read book Gas liquid Separation Using Axial Flow Cyclones written by Sin Yuan Ng and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Liquid Separation Within a Novel Axial Flow Cyclone Separator written by and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Cyclone separators have been described in detail and, although substantial research has been performed on solid / gas devices, the use of cyclones for gas / liquid separation has been comparatively ignored; this is particularly true for higher concentrations of liquid and for degassing applications. Consequently no generic models are available which will predict separation efficiency or pressure drop for all designs of cyclone. A novel design of axial flow cyclone called WELLSEP was examined for the purpose of degassing. This design was not believed to be optimal and no design criteria or performance prediction models were available for it. An experimental programme was therefore produced and executed to investigate changes in geometry and the affect of fluid dynamics. Changes to the length, vortex finder and swirl generator were examined first and then one design was selected and tested over a number of liquid flow rates, Gas Void Fractions (GVFs) and liquid extractions. Data was collected from the experiments which assisted in the development of semi-empirical models for the prediction of pressure drop and separation efficiency. These models could be used in the design of WELLSEP. Geometric and fluid dynamics changes have both been shown to influence the performance of the tested cyclone. The principal conclusions that have been drawn from this research are: " Of the tested designs, the design based upon a 30mm vortex finder diameter, settling chamber length of three times the diameter of the cyclone and a four start helix gave the optimum separation efficiency over the greatest range of conditions. 0 The separation efficiency is affected by the superficial liquid velocity and the liquid extraction but not the GVF." The dimensionless pressure drop coefficient (Euler number) is a function of liquid extraction and GVF. It may also be a function of the superficial liquid velocity but it is unproven by this research.
Download or read book Gas Cyclones and Swirl Tubes written by Alex C. Hoffmann and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 347 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book has been conceived to provide guidance on the theory and design of cyclone systems. Forthose new to the topic, a cyclone is, in its most basic form, a stationary mechanical device that utilizes centrifugal force to separate solid or liquid particles from a carrier gas. Gas enters near the top via a tangential or vaned inlet, which gives rise to an axially descending spiral of gas and a centrifugal force field that causes the incoming particles to concentrate along, and spiral down, the inner walls of the separator. The thus-segregated particulate phase is allowed to exit out an underflow pipe while the gas phase constricts, and - in most separators - reverses its axial direction of flow and exits out a separate overflow pipe. Cyclones are applied in both heavy and light industrial applications and may be designed as either classifiers or separators. Their applications are as plentiful as they are varied. Examples include their use in the separation or classification of powder coatings, plastic fines, sawdust, wood chips, sand, sintered/powdered meta!, plastic and meta! pellets, rock and mineral cmshings, carbon fines, grain products, pulverized coal, chalk, coal and coal ash, catalyst and petroleum coke fines, mist entrained off of various processing units and liquid components from scmbbing and drilling operations. They have even been applied to separate foam into its component gas and liquid phases in recent years.
Download or read book Gas Liquid Separation Within a Novel Axial Flow Cyclone Separator written by Philip James Dickson and published by . This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Hydrocyclone written by D. Bradley and published by Elsevier. This book was released on 2013-10-22 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Hydrocyclone reviews data on the theoretical, design, and performance aspects of the liquid cyclone, hydraulic cyclone, or hydrocyclone. The book aims to be a source of reference to those who are in industries employing the use and application of the hydrocyclone. The text covers the historical development of the cyclone; flow pattern and distribution of velocities within the cyclone body; operational characteristics and areas of application in different phase separations; and the operating and design variables affecting the performance of the hydrocyclone. Categories of cyclone; commercially available cyclone equipment; and the specific industrial applications of the hydrocyclone are also surveyed. The text will be of practical use to industrial engineers, mechanical engineers, plant operators, miners, and researchers.
Download or read book LIQUID GAS CYCLONE SEPARATION written by Sanford Fleeter and published by . This book was released on 1966 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt: The paper considers the secondary-flow in a liquid-gas mixture in a cyclone separator. By means of a momentum integral method, an engineering approximation to the secondary (heavy fluid) flow rate is obtained which makes use of an experimental velocity profile determined by ter Linden. This flow rate approximation is physically realistic and is partially verified in the laboratory. Tests were run on a separator to determine the effect of the variation of certain operating conditions and geometric factors on the separation of a liquid-gas mixture. The effect of these variations on the efficiency of separation and pressure drop across the separator as functions of the Reynolds and Weber numbers is presented. (Author).
Download or read book Performance Studies of Cyclone Separator written by Susarla Venkata Ananta Rama Sastry and published by LAP Lambert Academic Publishing. This book was released on 2013 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without the use of filters, through vortex separation. Rotational effects and gravity are used to separate mixtures of solids and fluids. A high speed rotating (air) flow is established within a cylindrical or conical container called a cyclone. Air flows in a helical pattern, beginning at the top (wide end) of the cyclone and ending at the bottom (narrow) end before exiting the cyclone in a straight stream through the center of the cyclone and out the top. Larger (denser) particles in the rotating stream have too much inertia to follow the tight curve of the stream, and strike the outside wall, then falling to the bottom of the cyclone where they can be removed. Cyclone separators have been used successfully in cement; agro; oil and various other industries. Its simple design and easy constructability make them very popular. This work is aimed for utilization by researchers, industrialists' and traditional businesses. Apart from this it will be especially relevant and useful for the students of Metallurgy, Mining, Mechanical engineering and Chemical engineering for carrying out research.
Download or read book Hydrocyclones written by L. Svarovsky and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is with great pleasure and satisfaction that we introduce this volume which comprises the papers accepted for the 4th International Conference on Hydrocyclones held in Southampton from 23rd to 25th September 1992. As the name implies, this is the fourth Conference in the series, with the previous ones held in Cambridge in 1980, Bath in 1984 and Oxford in 1987. The papers cover a wide span of activities, from fundamental research to advances in industrial practice and, as in the earlier volumes, make a significant contribution of lasting value to the technical literature on hydrocyclones. Hydrocyclones continue to widen their appeal to engineers; besides their traditional role in mineral processing they now attract a lot of attention in chemical engineering, the oil and gas industry, power generation, the food industry, textiles, metal working, waste water treatment, pharmaceuticals, biotechnology and other industries. The reason for this continuously increasing attention is, as David Parkinson (General Manager of Conoco (UK)) said recently, that" ... a hydrocyclone is an engineering dream, a machine with no moving parts." Yet as this Volume clearly shows, the hydrocyclone can do so many things and do them well, whether the application is in solid-liquid, liquid-liquid or liquid-gas separation.
Download or read book Droplet Separation written by Armin Bürkholz and published by Wiley-VCH. This book was released on 1989 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: International in coverage, the book offers industrial engineers a new and practical approach to solving problems in droplet separation. Without going into needless detail, it addresses such problems as the cost of droplet separation, the physical effects involved, separation efficiencies expected, and the lessons to be learned from industrial practice. Numerous diagrams, uncomplicated and reliable formulas, and lucid examples are presented to help design and calculate droplet separators. An exhaustive survey, based on twenty years of experience, the book is unparalleled in its field. Special feature: the introduction of a new dimensionless number.
Download or read book Handbook of Pollution Prevention and Cleaner Production Vol 1 Best Practices in the Petroleum Industry written by Nicholas P Cheremisinoff and published by William Andrew. This book was released on 2009-09-22 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new Handbook provides a series of reference guides to cleaner production methods, technologies, and practices for key industry sectors. Each volume covers, for each industry sector: * the manufacturing technologies * waste management * pollution * methods for estimating and reporting emissions * treatment and control technologies * worker and community health risk exposures * cost data for pollution management * cleaner production and prevention alternatives Best Practices in The Petroleum Industry provides an overview of refineries and gas plant operations and identifies the key Environmental Aspects, supported by case studies of major incidents that resulted in catastrophic releases of oil and refined products, and a critical assessment of the methodology and calculation procedures that the industry relies on in preparing emissions inventories. The authors offer alternative approaches to providing more accurate emissions estimates, and guidelines on cleaner production and pollution prevention practices for improving overall environmental performance. Overview of the key Environmental Aspects of gas plant operations and refineries Case studies of major incidents that resulted in catastrophic releases of oil and refined products, including the Santa Barbara oil spill of 1969 and the EXXON Valdez incident Provides guidelines on cleaner production and pollution prevention practices for improving overall environmental performance
Download or read book Solid liquid Separation written by and published by . This book was released on 1991 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design and Development of Gas liquid Cylindrical Cyclone Compact Separators for Three phase Flow First Quarterly Technical Progress Report October 1 1997 December 31 1997 written by and published by . This book was released on 1998 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents a brief overview of the activities accomplished during the first quarter of the budget period. The total tasks of the budget period are given initially, followed by the technical and scientific results achieved. A brief statement on the project work planned for the next quarter concludes the report. The objective of this five-year project is to expand the research activities of Tulsa University Separation Technology Projects (TUSTP) to multiphase oil/water/gas separation. This project will be executed in two phases. Phase I will focus on the investigations of the complex multiphase hydrodynamic flow behavior in a three-phase Gas-Liquid Cylindrical Cyclone (GLCC) Separator. The activities of this phase will include the development of a mechanistic model, a computational fluid dynamics (CFD) simulator, and detailed experimentation on the three-phase GLCC. The experimental and CFD simulation results will be suitably integrated with the mechanistic model. In Phase II, the developed GLCC separator will be tested under high pressure and real crudes conditions. This is crucial for validating the GLCC design for field application and facilitating easy and rapid technology deployment. Design criteria for industrial applications will be developed based on these results and will be incorporated into the mechanistic model by TUSTP. 3 figs.
Download or read book Liquid Carry over in Gas liquid Cylindrical Cyclone GLCC Compact Separators for Three phase Flow written by Srinivas Swaroop Kolla and published by . This book was released on 2007 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book DESIGN AND DEVELOPMENT OF GAS LIQUID CYLINDRICAL CYCLONE COMPACT SEPARATORS FOR THREE PHASE FLOW written by and published by . This book was released on 2000 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this five-year project (October, 1997-September, 2002) is to expand the current research activities of Tulsa University Separation Technology Projects (TUSTP) to multiphase oil/water/gas separation. This project will be executed in two phases. Phase I (1997-2000) will focus on the investigations of the complex multiphase hydrodynamic flow behavior in a three-phase Gas-Liquid Cylindrical Cyclone (GLCC{copyright}) Separator. The activities of this phase will include the development of a mechanistic model, a computational fluid dynamics (CFD) simulator, and detailed experimentation on the three-phase GLCC{copyright}. The experimental and CFD simulation results will be suitably integrated with the mechanistic model. In Phase II (2000-2002), the developed GLCC{copyright} separator will be tested under high pressure and real crudes conditions. This is crucial for validating the GLCC{copyright} design for field application and facilitating easy and rapid technology deployment. Design criteria for industrial applications will be developed based on these results and will be incorporated into the mechanistic model by TUSTP. This report presents a brief overview of the activities and tasks accomplished during the first half year (October 1, 1999-March 31, 2000) of the budget period (October 1, 1999-September 30, 2000). The total tasks of the budget period are given initially, followed by the technical and scientific results achieved till date. The report concludes with a detailed description of the plans for the conduct of the project for the second half year (April 1, 2000-September 30, 2000) of the current budget period.
Download or read book Performance Improvement of Gas Liquid Cylindrical Cyclone Separator Using Different Design for Tangential Inlet written by Nicolae Barbuceanu and published by . This book was released on 2001 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Optimizing the Efficiency of Cylindrical Cyclone Gas liquid Separators for Field Applications written by Adedeji Adebare and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Problems associated with the use of compact cylindrical cyclone gas/liquid (CCGL) separators can be attributed to two physical phenomena: gas carry-under and liquid carryover(LCO). Inadequate understanding of the complex multiphase hydrodynamic flowpattern inside the cylindrical separator has inhibited complete confidence in its designand use, hence the need for more research. While many works have been done with a fixed inlet slot to predict the operational efficiency of the cyclone separator, very little is known about how separator performance can be influenced due to changes in fluid properties. During the operations of the CCGLseparator the complex flow situations arising from severe foaming within the separator has not been addressed. Also the effects of emulsion formation under three phase flow conditions on the properties of cyclone separators are yet to be studied. An understanding of liquid holdup and hydrodynamic nature of flow in a compact separator under zero net liquid flow (ZNLF) and zero net gas flow (ZNGF) conditions is necessary in many field applications, especially for the prediction of LCO and in the design of the CCGL separators. Also, ZNLF holdup is an important parameter inpredicting bottom-hole pressures in pumping oil wells. This research investigated the effects of fluid properties such as density, foam and emulsion formation on ZNLF, zero net gas flow ZNGF, and LCO in compact cyclone separators; this was achieved by replacing water, which is the conventional fluid used as the liquid medium in many previous research efforts with a foamy oil while maintaining air as the gas phase. Variable-inlet-slots that regulate the artificial gravity environment created by the separator were used to check for improved separator performance. Also experiments to check separator response to a range of water-cut in three-phase flow were performed. All experiments were carried out under low constant separator pressures. The ZNLF holdup is observed to decrease as the density of the fluid medium decreases. Varying the inlet slot configurations and recombination points does not haveany effect on the ZNLF holdup when changes in density of the liquid phase occur. Comparisons with previous work show that there exists a wide variation in the LCO operational envelope when severe foaming occurs in the CCGL separator. At high water cut (greater than 30%), the separator LCO performance was observed to be normal. However, at water-cut below 30%, LCO was initiated much earlier ; this is attributed to severe foaming in the CCGL separator.
Download or read book Sustainable Resource Management written by Wenshan Guo and published by John Wiley & Sons. This book was released on 2021-07-19 with total page 835 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainable Resource Management Learn how current technologies can be used to recover and reuse waste products to reduce environmental damage and pollution In this two-volume set, Sustainable Resource Management: Technologies for Recovery and Reuse of Energy and Waste Materials delivers a compelling argument for the importance of the widespread adoption of a holistic approach to enhanced water, energy, and waste management practices. Increased population and economic growth, urbanization, and industrialization have put sustained pressure on the world’s environment, and this book demonstrates how to use organics, nutrients, and thermal heat to better manage wastewater and solid waste to deal with that reality. The book discusses basic scientific principles and recent technological advances in current strategies for resource recovery from waste products. It also presents solutions to pressing problems associated with energy production during waste management and treatment, as well as the health impacts created by improper waste disposal and pollution. Finally, the book discusses the potential and feasibility of turning waste products into resources. Readers will also enjoy: A thorough introduction and overview to resource recovery and reuse for sustainable futures An exploration of hydrothermal liquefaction of food waste, including the technology’s use as a potential resource recovery strategy A treatment of resource recovery and recycling from livestock manure, including the current state of the technology and future prospects and challenges A discussion of the removal and recovery of nutrients using low-cost adsorbents from single-component and multi-component adsorption systems Perfect for water and environmental chemists, engineers, biotechnologists, and food chemists, Sustainable Resource Management also belongs on the bookshelves of environmental officers and consultants, chemists in private industry, and graduate students taking programs in environmental engineering, ecology, or other sustainability related fields.
