Download or read book Gallium Nitride Epitaxy by a Novel Hybrid VPE Technique written by David J. Miller and published by Stanford University. This book was released on 2011 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gallium nitride is an important material for the production of next-generation visible and near-UV optical devices, as well as for high temperature electronic amplifiers and circuits; however there has been no bulk method for the production of GaN substrates for device layer growth. Instead, thick GaN layers are heteroepitaxially deposited onto non-native substrates (usually sapphire) by one of two vapor phase epitaxy (VPE) techniques: MOVPE (metalorganic VPE) or HVPE (hydride VPE). Each method has its strengths and weaknesses: MOVPE has precise growth rate and layer thickness control but it is slow and expensive; HVPE is a low-cost method for high rate deposition of thick GaN, but it lacks the precise control and heterojunction layer growth required for device structures. Because of the large (14%) lattice mismatch, GaN grown on sapphire requires the prior deposition of a low temperature MOVPE nucleation layer using a second growth process in a separate deposition system. Here we present a novel hybrid VPE system incorporating elements of both techniques, allowing MOVPE and HVPE in a single growth run. In this way, a thick GaN layer can be produced directly on sapphire. GaN growth commences as small (50-100 nm diameter) coherent strained 3-dimensional islands which coalesce into a continuous film, after which 2-dimensional layer growth commences. The coalescence of islands imparts significant stress into the growing film, which increases with the film thickness until catastrophic breakage occurs, in-situ. Additionally, the mismatch in thermal expansion rates induces compressive stress upon cooling from the growth temperature of 1025°C. We demonstrate a growth technique that mitigates these stresses, by using a 2-step growth sequence: an initial high growth rate step resulting in a pitted but relaxed film, followed by a low growth rate smoothing layer. As a result, thick (> 50 [Mu]m) and freestanding films have been grown successfully. X-ray rocking curve linewidth of 105 arcseconds and 10K PL indicating no "yellow" emission indicate that the material quality is higher than that produced by conventional MOVPE. By further modifying the hybrid system to include a metallic Mn source, it is possible to grow a doped semi-insulating GaN template for use in high frequency electronics devices.

Download or read book Hydride vapour phase epitaxy growth crystal properties and dopant incorporation in gallium nitride written by Patrick Hofmann and published by BoD – Books on Demand. This book was released on 2018-08-15 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation employs doping to investigate basic gallium nitride (GaN) crystal properties and to solve challenges of the hydride vapour phase epitaxy (HVPE) growth process. Whereas the first chapter is a short introduction to the history of the GaN single crystal growth, the 2nd chapter introduces to current crystal growth techniques, discusses properties of the GaN material system and the resulting influence on the applicable crystal growth techniques. HVPE, as a vapour phase epitaxy crystal growth method will be explained in greater detail, with focus on the used vertical reactor and its capabilities for doping. The 3rd chapter then focusses on point defects in GaN, specifically on intentionally introduced extrinsic point defects used for doping purposes, i.e. to achieve p-type, n-type or semi-insulating behaviour. Different dopants will be reviewed before the diffusion of point defects in a solid will be discussed. The in-situ introduction of iron, manganese, and carbon during crystal growth is employed in chapter 4 to compensate the unintentional doping (UID) of the GaN crystals, and therefore to achieve truly semi-insulating behaviour of the HVPE GaN. However the focus of this chapter lies on the characterisation of the pyroelectric coefficient (p), as semi-insulating properties are a necessary requirement for the applied Sharp-Garn measurement method. The creation of tensile stress due to in-situ silicon doping during GaN crystal growth is the topic of the 5th chapter. The tensile stress generation effect will be reproduced and the strain inside the crystal will be monitored ex-situ employing Raman spectroscopy. The n-type doping is achieved by using a vapour phase doping line and a process is developed to hinder the tensile strain generation effect. The 6th chapter concentrates on the delivery of the doping precursor via a solid state doping line, a newly developed doping method. Similar to chapter 5, the doping line is characterised carefully before the germanium doping is employed to the GaN growth. The focus lies on the homogeneity of the germanium doping and it is compared compared to the silicon doping and the vapour phase doping line. Benefits and drawbacks are discussed in conjunction with the obtained results. The germanium doping via solid state doping line is applied to the HVPE GaN growth process to measure accurately growth process related properties unique to the applied set of GaN growth parameters.

Download or read book Japanese Science and Technology written by and published by . This book was released on 1986 with total page 724 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ceramic Abstracts written by and published by . This book was released on 1999 with total page 950 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1984 with total page 1278 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2540 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Springer Handbook of Electronic and Photonic Materials written by Safa Kasap and published by Springer. This book was released on 2017-10-04 with total page 1536 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second, updated edition of this essential reference book provides a wealth of detail on a wide range of electronic and photonic materials, starting from fundamentals and building up to advanced topics and applications. Its extensive coverage, with clear illustrations and applications, carefully selected chapter sequencing and logical flow, makes it very different from other electronic materials handbooks. It has been written by professionals in the field and instructors who teach the subject at a university or in corporate laboratories. The Springer Handbook of Electronic and Photonic Materials, second edition, includes practical applications used as examples, details of experimental techniques, useful tables that summarize equations, and, most importantly, properties of various materials, as well as an extensive glossary. Along with significant updates to the content and the references, the second edition includes a number of new chapters such as those covering novel materials and selected applications. This handbook is a valuable resource for graduate students, researchers and practicing professionals working in the area of electronic, optoelectronic and photonic materials.

Download or read book Metalorganic Vapor Phase Epitaxy MOVPE written by Stuart Irvine and published by John Wiley & Sons. This book was released on 2019-10-07 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt: Systematically discusses the growth method, material properties, and applications for key semiconductor materials MOVPE is a chemical vapor deposition technique that produces single or polycrystalline thin films. As one of the key epitaxial growth technologies, it produces layers that form the basis of many optoelectronic components including mobile phone components (GaAs), semiconductor lasers and LEDs (III-Vs, nitrides), optical communications (oxides), infrared detectors, photovoltaics (II-IV materials), etc. Featuring contributions by an international group of academics and industrialists, this book looks at the fundamentals of MOVPE and the key areas of equipment/safety, precursor chemicals, and growth monitoring. It covers the most important materials from III-V and II-VI compounds to quantum dots and nanowires, including sulfides and selenides and oxides/ceramics. Sections in every chapter of Metalorganic Vapor Phase Epitaxy (MOVPE): Growth, Materials Properties and Applications cover the growth of the particular materials system, the properties of the resultant material, and its applications. The book offers information on arsenides, phosphides, and antimonides; nitrides; lattice-mismatched growth; CdTe, MCT (mercury cadmium telluride); ZnO and related materials; equipment and safety; and more. It also offers a chapter that looks at the future of the technique. Covers, in order, the growth method, material properties, and applications for each material Includes chapters on the fundamentals of MOVPE and the key areas of equipment/safety, precursor chemicals, and growth monitoring Looks at important materials such as III-V and II-VI compounds, quantum dots, and nanowires Provides topical and wide-ranging coverage from well-known authors in the field Part of the Materials for Electronic and Optoelectronic Applications series Metalorganic Vapor Phase Epitaxy (MOVPE): Growth, Materials Properties and Applications is an excellent book for graduate students, researchers in academia and industry, as well as specialist courses at undergraduate/postgraduate level in the area of epitaxial growth (MOVPE/ MOCVD/ MBE).

Download or read book International Aerospace Abstracts written by and published by . This book was released on 1997 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Technology of Gallium Nitride Crystal Growth written by Dirk Ehrentraut and published by Springer Science & Business Media. This book was released on 2010-06-14 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the important technological aspects of the growth of GaN single crystals by HVPE, MOCVD, ammonothermal and flux methods for the purpose of free-standing GaN wafer production.

Download or read book Physics Briefs written by and published by . This book was released on 1993 with total page 1058 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fundamentals of Silicon Carbide Technology written by Tsunenobu Kimoto and published by John Wiley & Sons. This book was released on 2014-11-24 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive introduction and up-to-date reference to SiC power semiconductor devices covering topics from material properties to applications Based on a number of breakthroughs in SiC material science and fabrication technology in the 1980s and 1990s, the first SiC Schottky barrier diodes (SBDs) were released as commercial products in 2001. The SiC SBD market has grown significantly since that time, and SBDs are now used in a variety of power systems, particularly switch-mode power supplies and motor controls. SiC power MOSFETs entered commercial production in 2011, providing rugged, high-efficiency switches for high-frequency power systems. In this wide-ranging book, the authors draw on their considerable experience to present both an introduction to SiC materials, devices, and applications and an in-depth reference for scientists and engineers working in this fast-moving field. Fundamentals of Silicon Carbide Technology covers basic properties of SiC materials, processing technology, theory and analysis of practical devices, and an overview of the most important systems applications. Specifically included are: A complete discussion of SiC material properties, bulk crystal growth, epitaxial growth, device fabrication technology, and characterization techniques. Device physics and operating equations for Schottky diodes, pin diodes, JBS/MPS diodes, JFETs, MOSFETs, BJTs, IGBTs, and thyristors. A survey of power electronics applications, including switch-mode power supplies, motor drives, power converters for electric vehicles, and converters for renewable energy sources. Coverage of special applications, including microwave devices, high-temperature electronics, and rugged sensors. Fully illustrated throughout, the text is written by recognized experts with over 45 years of combined experience in SiC research and development. This book is intended for graduate students and researchers in crystal growth, material science, and semiconductor device technology. The book is also useful for design engineers, application engineers, and product managers in areas such as power supplies, converter and inverter design, electric vehicle technology, high-temperature electronics, sensors, and smart grid technology.

Download or read book Silicon Carbide written by Wolfgang J. Choyke and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 911 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the 1997 publication of "Silicon Carbide - A Review of Fundamental Questions and Applications to Current Device Technology" edited by Choyke, et al., there has been impressive progress in both the fundamental and developmental aspects of the SiC field. So there is a growing need to update the scientific community on the important events in research and development since then. The editors have again gathered an outstanding team of the world's leading SiC researchers and design engineers to write on the most recent developments in SiC.

Download or read book CRC Handbook of Metal Etchants written by Perrin Walker and published by CRC Press. This book was released on 1990-12-11 with total page 1434 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication presents cleaning and etching solutions, their applications, and results on inorganic materials. It is a comprehensive collection of etching and cleaning solutions in a single source. Chemical formulas are presented in one of three standard formats - general, electrolytic or ionized gas formats - to insure inclusion of all necessary operational data as shown in references that accompany each numbered formula. The book describes other applications of specific solutions, including their use on other metals or metallic compounds. Physical properties, association of natural and man-made minerals, and materials are shown in relationship to crystal structure, special processing techniques and solid state devices and assemblies fabricated. This publication also presents a number of organic materials which are widely used in handling and general processing...waxes, plastics, and lacquers for example. It is useful to individuals involved in study, development, and processing of metals and metallic compounds. It is invaluable for readers from the college level to industrial R & D and full-scale device fabrication, testing and sales. Scientific disciplines, work areas and individuals with great interest include: chemistry, physics, metallurgy, geology, solid state, ceramic and glass, research libraries, individuals dealing with chemical processing of inorganic materials, societies and schools.

Download or read book Fundamentals of Semiconductor Manufacturing and Process Control written by Gary S. May and published by John Wiley & Sons. This book was released on 2006-05-26 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: A practical guide to semiconductor manufacturing from processcontrol to yield modeling and experimental design Fundamentals of Semiconductor Manufacturing and Process Controlcovers all issues involved in manufacturing microelectronic devicesand circuits, including fabrication sequences, process control,experimental design, process modeling, yield modeling, and CIM/CAMsystems. Readers are introduced to both the theory and practice ofall basic manufacturing concepts. Following an overview of manufacturing and technology, the textexplores process monitoring methods, including those that focus onproduct wafers and those that focus on the equipment used toproduce wafers. Next, the text sets forth some fundamentals ofstatistics and yield modeling, which set the foundation for adetailed discussion of how statistical process control is used toanalyze quality and improve yields. The discussion of statistical experimental design offers readers apowerful approach for systematically varying controllable processconditions and determining their impact on output parameters thatmeasure quality. The authors introduce process modeling concepts,including several advanced process control topics such asrun-by-run, supervisory control, and process and equipmentdiagnosis. Critical coverage includes the following: * Combines process control and semiconductor manufacturing * Unique treatment of system and software technology and managementof overall manufacturing systems * Chapters include case studies, sample problems, and suggestedexercises * Instructor support includes electronic copies of the figures andan instructor's manual Graduate-level students and industrial practitioners will benefitfrom the detailed exami?nation of how electronic materials andsupplies are converted into finished integrated circuits andelectronic products in a high-volume manufacturingenvironment. An Instructor's Manual presenting detailed solutions to all theproblems in the book is available from the Wiley editorialdepartment. An Instructor Support FTP site is also available.

Download or read book MEMS Materials and Processes Handbook written by Reza Ghodssi and published by Springer Science & Business Media. This book was released on 2011-03-18 with total page 1211 pages. Available in PDF, EPUB and Kindle. Book excerpt: MEMs Materials and Processes Handbook" is a comprehensive reference for researchers searching for new materials, properties of known materials, or specific processes available for MEMS fabrication. The content is separated into distinct sections on "Materials" and "Processes". The extensive Material Selection Guide" and a "Material Database" guides the reader through the selection of appropriate materials for the required task at hand. The "Processes" section of the book is organized as a catalog of various microfabrication processes, each with a brief introduction to the technology, as well as examples of common uses in MEMs.

Download or read book Integrated Ring Resonators written by Dominik G. Rabus and published by Springer. This book was released on 2007-04-26 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: The optical filter is resonator based. The required passband shape of ring resonator-filters can be custom designed by the use of configurations of various ring coupled resonators. This book describes the current state-of-the-art on these devices. It provides an in-depth knowledge of the simulation, fabrication and characterization of ring resonators for use as example filters, lasers, sensors.