Download or read book Fuel Flexible Combustion Systems for High Efficiency Utilization of Opportunity Fuels in Gas Turbines written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this program was to develop low-emissions, efficient fuel-flexible combustion technology which enables operation of a given gas turbine on a wider range of opportunity fuels that lie outside of current natural gas-centered fuel specifications. The program encompasses a selection of important, representative fuels of opportunity for gas turbines with widely varying fundamental properties of combustion. The research program covers conceptual and detailed combustor design, fabrication, and testing of retrofitable and/or novel fuel-flexible gas turbine combustor hardware, specifically advanced fuel nozzle technology, at full-scale gas turbine combustor conditions. This project was performed over the period of October 2008 through September 2011 under Cooperative Agreement DE-FC26-08NT05868 for the U.S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled "Fuel Flexible Combustion Systems for High-Efficiency Utilization of Opportunity Fuels in Gas Turbines". The overall objective of this program was met with great success. GE was able to successfully demonstrate the operability of two fuel-flexible combustion nozzles over a wide range of opportunity fuels at heavy-duty gas turbine conditions while meeting emissions goals. The GE MS6000B ("6B") gas turbine engine was chosen as the target platform for new fuel-flexible premixer development. Comprehensive conceptual design and analysis of new fuel-flexible premixing nozzles were undertaken. Gas turbine cycle models and detailed flow network models of the combustor provide the premixer conditions (temperature, pressure, pressure drops, velocities, and air flow splits) and illustrate the impact of widely varying fuel flow rates on the combustor. Detailed chemical kinetic mechanisms were employed to compare some fundamental combustion characteristics of the target fuels, including flame speeds and lean blow-out behavior. Perfectly premixed combustion experiments were conducted to provide experimental combustion data of our target fuels at gas turbine conditions. Based on an initial assessment of premixer design requirements and challenges, the most promising sub-scale premixer concepts were evaluated both experimentally and computationally. After comprehensive screening tests, two best performing concepts were scaled up for further development. High pressure single nozzle tests were performed with the scaled premixer concepts at target gas turbine conditions with opportunity fuels. Single-digit NOx emissions were demonstrated for syngas fuels. Plasma-assisted pilot technology was demonstrated to enhance ignition capability and provide additional flame stability margin to a standard premixing fuel nozzle. However, the impact of plasma on NOx emissions was observed to be unacceptable given the goals of this program and difficult to avoid.

Download or read book Development of Fuel Flexible Combustion Systems Utilizing Opportunity Fuels in Gas Turbines written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: General Electric Global Research will define, develop, and test new fuel nozzle technology concepts for gas turbine operation on a wide spectrum of opportunity fuels and/or fuel blends. This will enable gas turbine operation on ultra-low Btu fuel streams such as very weak natural gas, highly-diluted industrial process gases, or gasified waste streams that are out of the capability range of current turbine systems.

Download or read book FUEL FLEXIBLE GASIFICATION COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION READY CO2 written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the thermodynamic efficiency and environmental impact performance of fossil fuel utilization. General Electric Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Advanced Gasification-Combustion (AGC) concept to produce H[sub 2] and sequestration-ready CO[sub 2] from solid fuels. The AGC module offers potential for reduced cost and increased energy efficiency relative to conventional gasification and combustion systems. GE EER was awarded a Vision-21 program from U.S. DOE NETL to develop the AGC technology. Work on this three-year program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T.R. Miles, Technical Consultants, Inc. In the AGC technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO[sub 2], and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on preliminary modeling work in the first quarter of this program, has an estimated process efficiency of approximately 67% based on electrical and H[sub 2] energy outputs relative to the higher heating value of coal. The three-year R & D program will determine the operating conditions that maximize separation of CO[sub 2] and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the AGC concept. This is the third quarterly technical progress report for the Vision-21 AGC program supported by U.S. DOE NETL (Contract: DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting April 1, 2001 and ending June 30, 2001. The report includes an introduction summarizing the AGC concept, main program tasks, objectives of this program, and provides a summary of program activities covering program management and progress in first year tasks including lab- and bench-scale design, facilities preparation, and engineering studies.

Download or read book Advanced Technologies for Gas Turbines written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2020-04-19 with total page 137 pages. Available in PDF, EPUB and Kindle. Book excerpt: Leadership in gas turbine technologies is of continuing importance as the value of gas turbine production is projected to grow substantially by 2030 and beyond. Power generation, aviation, and the oil and gas industries rely on advanced technologies for gas turbines. Market trends including world demographics, energy security and resilience, decarbonization, and customer profiles are rapidly changing and influencing the future of these industries and gas turbine technologies. Technology trends that define the technological environment in which gas turbine research and development will take place are also changing - including inexpensive, large scale computational capabilities, highly autonomous systems, additive manufacturing, and cybersecurity. It is important to evaluate how these changes influence the gas turbine industry and how to manage these changes moving forward. Advanced Technologies for Gas Turbines identifies high-priority opportunities for improving and creating advanced technologies that can be introduced into the design and manufacture of gas turbines to enhance their performance. The goals of this report are to assess the 2030 gas turbine global landscape via analysis of global leadership, market trends, and technology trends that impact gas turbine applications, develop a prioritization process, define high-priority research goals, identify high-priority research areas and topics to achieve the specified goals, and direct future research. Findings and recommendations from this report are important in guiding research within the gas turbine industry and advancing electrical power generation, commercial and military aviation, and oil and gas production.

Download or read book Fuel Flexible Combustion System for Co production Plant Applications written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Future high-efficiency, low-emission generation plants that produce electric power, transportation fuels, and/or chemicals from fossil fuel feed stocks require a new class of fuel-flexible combustors. In this program, a validated combustor approach was developed which enables single-digit NO(subscript x) operation for a future generation plants with low-Btu off gas and allows the flexibility of process-independent backup with natural gas. This combustion technology overcomes the limitations of current syngas gas turbine combustion systems, which are designed on a site-by-site basis, and enable improved future co-generation plant designs. In this capacity, the fuel-flexible combustor enhances the efficiency and productivity of future co-production plants. In task 2, a summary of market requested fuel gas compositions was created and the syngas fuel space was characterized. Additionally, a technology matrix and chemical kinetic models were used to evaluate various combustion technologies and to select two combustor concepts. In task 4 systems analysis of a co-production plant in conjunction with chemical kinetic analysis was performed to determine the desired combustor operating conditions for the burner concepts. Task 5 discusses the experimental evaluation of three syngas capable combustor designs. The hybrid combustor, Prototype-1 utilized a diffusion flame approach for syngas fuels with a lean premixed swirl concept for natural gas fuels for both syngas and natural gas fuels at FA+e gas turbine conditions. The hybrid nozzle was sized to accommodate syngas fuels ranging from (almost equal to)100 to 280 btu/scf and with a diffusion tip geometry optimized for Early Entry Co-generation Plant (EECP) fuel compositions. The swozzle concept utilized existing GE DLN design methodologies to eliminate flow separation and enhance fuel-air mixing. With changing business priorities, a fully premixed natural gas & syngas nozzle, Protoytpe-1N, was also developed later in the program. It did not have the diluent requirements of Prototype-1 and was demonstrated at targeted gas turbine conditions. The TVC combustor, Prototype-2, premixes the syngas with air for low emission performance. The combustor was designed for operation with syngas and no additional diluents. The combustor was successfully operated at targeted gas turbine conditions. Another goal of the program was to advance the status of development tools for syngas systems. In Task 3 a syngas flame evaluation facility was developed. Fundamental data on syngas flame speeds and flame strain were obtained at pressure for a wide range of syngas fuels with preheated air. Several promising reduced order kinetic mechanisms were compared with the results from the evaluation facility. The mechanism with the best agreement was selected for application to syngas combustor modeling studies in Task 6. Prototype-1 was modeled using an advanced LES combustion code. The tools and combustor technology development culminate in a full-scale demonstration of the most promising technology in Task 8. The combustor was operated at engine conditions and evaluated against the various engine performance requirements.

Download or read book Novel Combustion Concepts for Sustainable Energy Development written by Avinash K Agarwal and published by Springer. This book was released on 2014-12-19 with total page 561 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises research studies of novel work on combustion for sustainable energy development. It offers an insight into a few viable novel technologies for improved, efficient and sustainable utilization of combustion-based energy production using both fossil and bio fuels. Special emphasis is placed on micro-scale combustion systems that offer new challenges and opportunities. The book is divided into five sections, with chapters from 3-4 leading experts forming the core of each section. The book should prove useful to a variety of readers, including students, researchers, and professionals.

Download or read book Combustion Engineering Issues for Solid Fuel Systems written by Bruce G. Miller and published by Academic Press. This book was released on 2008-07-02 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design, construct and utilize fuel systems using this comprehensive reference work. Combustion Engineering Issues for Solid Fuel Systems combines modeling, policy/regulation and fuel properties with cutting edge breakthroughs in solid fuel combustion for electricity generation and industrial applications. This book moves beyond theory to provide readers with real-life experiences and tips for addressing the various technical, operational and regulatory issues that are associated with the use of fuels. With the latest information on CFD modeling and emission control technologies, Combustion Engineering Issues for Solid Fuel Systems is the book practicing engineers as well as managers and policy makers have been waiting for. Provides the latest information on CFD modeling and emission control technologies Comprehensive coverage of combustion systems and fuel types Addresses policy and regulatory concerns at a technical level Tackles various technical and operational issues

Download or read book Fuel Flexible Low Emission Catalytic Combustor for Opportunity Fuel Applications written by and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Limited fuel resources, increasing energy demand and stringent emission regulations are drivers to evaluate process off-gases or process waste streams as fuels for power generation. Often these process waste streams have low energy content and/or highly reactive components. Operability of low energy content fuels in gas turbines leads to issues such as unstable and incomplete combustion. On the other hand, fuels containing higher-order hydrocarbons lead to flashback and auto-ignition issues. Due to above reasons, these fuels cannot be used directly without modifications or efficiency penalties in gas turbine engines. To enable the use of these wide variety of fuels in gas turbine engines a rich catalytic lean burn (RCL®) combustion system was developed and tested in a subscale high pressure (10 atm.) rig. The RCL® injector provided stability and extended turndown to low Btu fuels due to catalytic pre-reaction. Previous work has shown promise with fuels such as blast furnace gas (BFG) with LHV of 85 Btu/ft3 successfully combusted. This program extends on this work by further modifying the combustor to achieve greater catalytic stability enhancement. Fuels containing low energy content such as weak natural gas with a Lower Heating Value (LHV) of 6.5 MJ/m3 (180 Btu/ft3 to natural gas fuels containing higher hydrocarbon (e.g ethane) with LHV of 37.6 MJ/m3 (1010 Btu/ft3) were demonstrated with improved combustion stability; an extended turndown (defined as the difference between catalytic and non-catalytic lean blow out) of greater than 250oF was achieved with CO and NOx emissions lower than 5 ppm corrected to 15% O2. In addition, for highly reactive fuels the catalytic region preferentially pre-reacted the higher order hydrocarbons with no events of flashback or auto-ignition allowing a stable and safe operation with low NOx and CO emissions.

Download or read book Combustion in Advanced Gas Turbine Systems written by I. E. Smith and published by Elsevier. This book was released on 2014-05-17 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cranfield International Symposium Series, Volume 10: Combustion in Advanced Gas Turbine Systems covers the proceedings of an International Propulsion Symposium, held at the College of Aeronautics in Cranfield in April 1967. The book focuses on the processes, methodologies, reactions, and transformations involved in chemical combustion. The selection first takes a look at the design considerations in advanced gas turbine combustion chambers, combustion in industrial gas turbines, and combustion development on the Rolls-Royce Spey engine. Discussions focus on mechanical condition, carbon-formation and exhaust smoke, system requirements, fuel oil ash deposition and corrosion, combustion-system design, performance requirements, types of primary zone, fuel injection, and combustion chamber types. The text then examines subsonic flow flameholder studies using a low pressure simulation technique; stabilization of hydrogen diffusion flames by flame-holders in supersonic flow at low stagnation temperatures; and augmentation systems for turbofan engines. The book takes a look at a consideration of the possible use of refractory ceramic materials for advanced combustion chamber design; cooling of flame tubes by steam injection; and combustion problems in the massive steam injection gas turbine. The selection is a valuable source of information for researchers interested in the process of combustion in advanced gas turbine systems.

Download or read book Advanced Turbulent Combustion Modeling for Gas Turbine Application written by Andrea Donini and published by Andrea Donini. This book was released on with total page 173 pages. Available in PDF, EPUB and Kindle. Book excerpt: In spite of the increasing presence of renewable energy sources, fossil fuels will remain the primary supply of the world's energy needs for the upcoming future. Modern gas-turbine based systems represent one of the most efficient large-scale power generation technology currently available. Alongside this, gas-turbine power plants operate with very low emissions, have flexible operational characteristics and are able to utilize a broad range of fuels. It is expected that gas-turbine based plants will play an important role as an effective means of converting combustion energy in the future as well, because of the vast potential energy savings. The numerical approach to the design of complex systems such as gas-turbines has gained a continuous growth of interest in the last few decades. This because simulations are foreseen to provide a tremendous increase in the combustor efficiency, fuel-flexibility and quality over the next future. In this dissertation, an advanced turbulent combustion technique is implemented and progressively developed for the simulation of all the features that are typically observed in stationary gas-turbine combustion, including hydrogen as a fuel. The developed turbulent combustion model retains most of the accuracy of a detailed simulation while drastically reducing its computational time. As a result of this work, the advancement of power generation plants can be accelerated, paving the way for future developments of alternative fuel usage in a cleaner and more efficient combustion.

Download or read book Modern Gas Turbine Systems written by Peter Jansohn and published by Elsevier. This book was released on 2013-08-31 with total page 849 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern gas turbine power plants represent one of the most efficient and economic conventional power generation technologies suitable for large-scale and smaller scale applications. Alongside this, gas turbine systems operate with low emissions and are more flexible in their operational characteristics than other large-scale generation units such as steam cycle plants. Gas turbines are unrivalled in their superior power density (power-to-weight) and are thus the prime choice for industrial applications where size and weight matter the most. Developments in the field look to improve on this performance, aiming at higher efficiency generation, lower emission systems and more fuel-flexible operation to utilise lower-grade gases, liquid fuels, and gasified solid fuels/biomass. Modern gas turbine systems provides a comprehensive review of gas turbine science and engineering. The first part of the book provides an overview of gas turbine types, applications and cycles. Part two moves on to explore major components of modern gas turbine systems including compressors, combustors and turbogenerators. Finally, the operation and maintenance of modern gas turbine systems is discussed in part three. The section includes chapters on performance issues and modelling, the maintenance and repair of components and fuel flexibility. Modern gas turbine systems is a technical resource for power plant operators, industrial engineers working with gas turbine power plants and researchers, scientists and students interested in the field. Provides a comprehensive review of gas turbine systems and fundamentals of a cycle Examines the major components of modern systems, including compressors, combustors and turbines Discusses the operation and maintenance of component parts

Download or read book CONCEPTUAL STUDIES OF A FUEL FLEXIBLE LOW SWIRL COMBUSTION SYSTEM FOR THE GAS TURBINE IN CLEAN COAL POWER PLANTS written by and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper reports the results of preliminary analyses that show the feasibility of developing a fuel flexible (natural gas, syngas and high-hydrogen fuel) combustion system for IGCC gas turbines. Of particular interest is the use of Lawrence Berkeley National Laboratory's DLN low swirl combustion technology as the basis for the IGCC turbine combustor. Conceptual designs of the combustion system and the requirements for the fuel handling and delivery circuits are discussed. The analyses show the feasibility of a multi-fuel, utility-sized, LSI-based, gas turbine engine. A conceptual design of the fuel injection system shows that dual parallel fuel circuits can provide range of gas turbine operation in a configuration consistent with low pollutant emissions. Additionally, several issues and challenges associated with the development of such a system, such as flashback and auto-ignition of the high-hydrogen fuels, are outlined.

Download or read book Gas Turbines for Electric Power Generation written by S. Can Gülen and published by Cambridge University Press. This book was released on 2019-02-14 with total page 735 pages. Available in PDF, EPUB and Kindle. Book excerpt: Everything you wanted to know about industrial gas turbines for electric power generation in one source with hard-to-find, hands-on technical information.

Download or read book Gas Turbine Emissions written by Timothy C. Lieuwen and published by Cambridge University Press. This book was released on 2013-07-08 with total page 385 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of clean, sustainable energy systems is a preeminent issue in our time. Gas turbines will continue to be important combustion-based energy conversion devices for many decades to come, used for aircraft propulsion, ground-based power generation, and mechanical-drive applications. This book compiles the key scientific and technological knowledge associated with gas turbine emissions into a single authoritative source.

Download or read book Coal Power Systems Strategic Plan Multi year Program Plans written by United States. Office of Fossil Energy and published by DIANE Publishing. This book was released on 1999 with total page 49 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Renewable Fuels written by Jacqueline O'Connor and published by Cambridge University Press. This book was released on 2022-12-15 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: Focusing on a critical aspect of the future clean energy system - renewable fuels - this book will be your complete guide on how these fuels are manufactured, the considerations associated with utilising them, and their real-world applications. Written by experts across the field, the book presents many professional perspectives, providing an in-depth understanding of this crucial topic. Clearly explained and organised into four key parts, this book explores the technical aspects written in an accessible way. First, it discusses the dominant energy conversion approaches and the impact that fuel properties have on system operability. Part II outlines the chemical carrier options available for these conversion devices, including gaseous, liquid, and solid fuels. In the third part, it describes the physics and chemistry of combustion, revealing the issues associated with utilizing these fuels. Finally, Part IV presents real-world case studies, demonstrating the successful pathways towards a net-zero carbon future.

Download or read book High Temperature Air Combustion written by Hiroshi Tsuji and published by CRC Press. This book was released on 2002-12-03 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: Maximize efficiency and minimize pollution: the breakthrough technology of high temperature air combustion (HiTAC) holds the potential to overcome the limitations of conventional combustion and allow engineers to finally meet this long-standing imperative. Research has shown that HiTAC technology can provide simultaneous reduction of CO2 and nitric