Download or read book Fittings Straight Threaded Boss Or Flanged Fluid Connection Procurement Specification written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for straight threaded boss or flanged fluid connection fittings (see Section 6) for use in all types of fluid systems. Revise AS4875 by including individual tables showing recommended operating pressure ratings for fittings when used on CRES and Al Alloy tubing. Document title revised. Note 2.1 updated to include specifications mentioned herein. Note 3.1.1 revised. Note 3.1.2 added. Notes /5/, /6/, /7/, and /8/ and optional material added to Table 1. Note 2.1 and Table 1, AMS4134 replaced by AMS4133 (AMS4134 was inadvertently listed as 2014-T6. Appropriate T6 spec should be AMS4133). Upper range of hardness requirement in note 3.3.3 revised. Note 3.6.4 (d) revised. Note 6.2 revised. Historical information added to Note 6.2. Tables 5A and 5B added. Note 6.2.2 revised and supersession Table 6 added. Lessons learned Note 6.2.4 added. General updates included. Note 4.5.1.2 revised to remove the statement that destructive testing is required to retain QML status. This requirement is regulated by AC7112.
Download or read book Fittings and Bosses Pipe Threaded Fluid Connection Procurement Specification written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for pipe threaded fluid connection fittings (see Section 6) for use in all types of fluid systems. Revise AS4842 by including individual tables showing recommended operating pressure ratings for fittings when used on CRES and Al Alloy tubing. Document title revised. Note 2.1 updated to include specifications mentioned herein. Flagnotes /7/ through /10/ added to Table 1. Note 3.1.1 revised to align with current QML statement. Note 3.1.2 added. Notes /7/, /8/, /9/, and /10/ added to Table 1. Upper range of hardness requirement in note 3.3.3 revised. Note 3.4.4 reworded to include color requirement. Note 4.5.1.2 revised to remove the statement that destructive testing is required to retain QML status. This requirement is regulated by AC7112. Historical information added to note 6.2. Tables 5A and 5B added. Note 6.2.2 revised and supersession Table 7 added. Lessons learned note 6.2.4 added. General updates included.
Download or read book Fittings Straight Threaded Boss Or Flanged Fluid Connection written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for straight threaded boss or flanged fluid connection fittings (see Section 6) for use in all types of fluid systems. This document has been reaffirmed to comply with the SAE 5-Year Review policy.
Download or read book Index of Specifications and Standards written by and published by . This book was released on 2005 with total page 810 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Department Of Defense Index of Specifications and Standards Numerical Listing Part II July 2005 written by and published by DIANE Publishing. This book was released on with total page 809 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fittings Straight Thread Boss Or Flanged to 37 Flared Fluid Connection written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both straight thread boss or flanged connections and 37° flared connections for use in all types of fluid systems. This document has been reaffirmed to comply with the SAE 5-Year Review policy.
Download or read book Aerospace Standard AS4875 Rev A written by and published by . This book was released on 2016 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fittings 37 Internal Flare Fluid Connection Procurement Specification written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 37° flared tube fittings or machined internal cone fluid connection fittings for use with 37° external cone, spherical nose and seal ring fittings in all types of aerospace fluid systems (see Section 6). Administrative revision to correct paragraph cross-references throughout the document and applicable document references.
Download or read book PACKING PREFORMED STRAIGHT THREAD TUBE FITTING BOSS HYDRAULIC 65 F TO 275 F written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: EXAMPLE OF THE PART NUMBER ADDED AND PROCUREMENT SPECIFICATION DESIGNATION UPDATED.
Download or read book Fittings 37 Degree Internal Flare Fluid Connection Procurement Specification written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 37 degree flared tube fittings or machined internal cone fluid connection fittings for use with 37 degree external cone, spherical nose, and seal ring fittings in all types of aerospace fluid systems (see Section 6). Note 4.5.1.2 revised to remove the statement that destructive testing is required to retain QML status. This requirement is regulated by AC7112.
Download or read book Fittings Straight Thread Port Or Flanged to 24 Cone Flareless Fluid Connection written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both straight thread port or flanged connections and 24° cone flareless connections for use in all types of fluid systems. AS4875/3 has been reaffirmed to comply with the SAE five-year review policy.
Download or read book Fittings 24 Cone Flareless Fluid Connection 3000 Psi Supplement 1 written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This supplement forms a part of the Aerospace Standard AS18280 Fittings, 24° Cone, Flareless, Fluid Connection, 3000 psi, and shall be used to identify fitting standards citing this procurement specification. AS18280SUP1A has been reaffirmed to comply with the SAE five-year review policy.
Download or read book BOSS FLUID CONNECTION INTERNAL STRAIGHT THREAD SHALLOW TAP written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: AS1171A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. 1FOR USE WITH FITTING ENDS PER AS 930 WHEN TAP DEPTHS OF MS33649 ARE CONSIDERED EXCESSIVE FOR INTENDED DESIGN. 2SURFACE TEXTURE: ANSI B46.1-1962. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES (3.2 MICROMETRES). 3UNLESS OTHERWISE SPECIFIED ON THE FIELD' OF THE DRAWING OR IN NOTE 4, THE DIMENSIONS SHOWN FOR THE BLIND TAP DESIGN ALSO APPLY TO THE THRU THREAD DESIGN, AND VICE VERSA. BOTH DESIGNS MAY BE MACHINED WITH EITHER A RECESSED OR RAISED SURFACE K, AS APPLICABLE. 4MINIMUM FLAT BOSS FACE. CLEARANCE PROVISIONS FOR FITTING, WRENCH, FITTING INSTALLATION AND TOOL FILLET RADII MUST BE ADDED AS REQUIRED. G MINIMUM DIAMETER MAY BE REDUCED BY .040 (1.01) WHEN IT DEFINES THE LIMIT OF A RAISED SURFACE AND STRENGTH REQUIREMENTS PERMIT. 5TAP DRILL DEPTH SHALL BE SUFFICIENT TO PROVIDE THREAD RUNOUT. 6B MINIMUM IS THE FULL THREAD DEPTH REQUIREMENT FOR THE BLIND TAP DESIGN AND PROVIDES MINIMIM CLEARANCE ENVELOPE FOR THE AS 930 FITTING END IN THRU THREAD DESIGN. ADDITIONAL CLEARANCE SHALL BE PROVIDED IN THRU THREAD DESIGN WHEN NEEDED TO PREVENT CHOKED FLOW. 7DIMENSIONING AND TOLERANCING: ANSI Y14.5-1973. 8THRU THREAD DESIGN SHALL HAVE SUFFICIENT THREADS TO MEET STRENGTH REQUIREMENTS OF MATERIAL USED. 9C IS THE MINIMUM DIAMETER FOR UNRESTRICTED FLUID FLOW. HOLE MAY BE ANY SIZE OR SHAPE PROVIDED CLEARANCE IS MAINTAINED TO B DEPTH FOR FITTING. 10REMOVE ALL BURRS AND SLIVERS AND BREAK SHARP EDGES. 11DIMENSIONS IN INCHES (MILLIMETRES). METRIC CONVERSIONS ARE INTERNATIONAL SYSTEM UNITS (SI). 12THIS IS A DESIGN STANDARD, NOT TO BE USED AS A PART NUMBER.
Download or read book Fittings and Bosses Pipe Threaded Fluid Connection written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 37° flared tube or machined cone fluid connection fittings (see Section 6) for use in all types of fluid systems. AS4842 has been reaffirmed to comply with the SAE five-year review policy.
Download or read book TUBE FITTINGS METRIC AEROSPACE FLUID SYSTEMS SEPARABLE GENERAL SPECIFICATION FOR written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 1983 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard establishes the basic performance and quality criteria for screw-together tube fitting assemblies and port connectors. It was prepared to standardize on the qualification test and procurement requirements for ISO standard tube fittings. The test requirements are intended to satisfy the most strenuous demands encountered in a high performance aircraft hydraulic system. The procurement requirements are intended to assure that fittings which are bought to this specification are of the same quality as the fittings used during the original qualification testing. Compliance with these test and procurement requirements is necessary for fittings which are used in control systems where a malfunction could affect the safety of flight.
Download or read book Hydraulic Hose Fittings written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES. The following are hose fitting types contained in this document: a. Male dryseal pipe thread type hose fittings shall be as shown in Figures 1A to 1C for the respective styles, and in Tables 1A to 1M for the applicable hoses and sizes. b. Male straight thread O-ring boss type hose fittings shall be as shown in Figures 2A and 2B for the respective styles, and in Tables 2A to 2H for the applicable hoses and sizes. c. Male 37-degree flared type hose fittings shall be as shown in Figures 3A to 3C for the respective styles, and in Tables 3A to 3L for the applicable hoses and sizes. d. Female 37-degree flared type hose fittings shall be as shown in Figures 4A to 7B for the respective styles and shapes, and in Tables 4A to 4M for the applicable hoses and sizes. e. Male 45-degree flared type hose fittings shall be as shown in Figures 8A and 8B for the respective styles, and in Tables 5A to 5E for the applicable hoses and sizes. f. Female 45-degree flared type hose fittings shall be as shown in Figures 9A to 12B for the respective styles and shapes, and in Tables 6A to 6E for the applicable hoses and sizes. g. Male flareless type hose fittings shall be as shown in Figures 13A and 13B for the respective styles, and in Tables 7A and 7B for the applicable hoses and sizes. h. Female flareless type hose fittings shall be as shown in Figures 14A to 14C for the respective styles, and in Tables 8A and 8B for the applicable hoses and sizes. i. 4-bolt split flange type hose fittings shall be as shown in Figures 15A to 21C for the respective styles and shapes, and in Tables 9A to 9I2 for the applicable hoses and sizes. j. Female O-ring face seal hose fittings shall be as shown in Figures 22A to 25B for the respective styles, and Tables 10A to 10L for the applicable hoses and sizes. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
Download or read book Bosses Fluid Connection Internal Straight Thread written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
