Download or read book Feasibility Study and Evaluation of Applying EDM Hole Drilling Method for Measuring Residual Stress written by 許富銓 and published by . This book was released on 2005 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hole Drilling Method for Measuring Residual Stresses written by Gary S. and published by Springer Nature. This book was released on 2022-05-31 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the theory and practice of the Hole-Drilling Method for measuring residual stresses in engineering components. Such measurements are important because residual stresses have a "hidden" character because they exist locked-in within a material, independent of any external load. These stresses are typically created during component manufacture, for example, during welding, casting, or forming. Because of their hidden nature, residual stresses are difficult to measure and consequently are often ignored. However, they directly add to loading stresses and can cause catastrophic failure if not properly included during engineering design. Thus, there is an urgent need to be able to identify and measure residual stresses conveniently and reliably. The Hole-Drilling Method provides an adaptable and well-proven method for measuring residual stresses in a wide range of materials and component types. It is convenient to use and gives reliable results. Because of the hidden nature of residual stresses, the measurement method must necessarily be indirect, thus, additional care and conceptual understanding are necessary to achieve successful results. This book provides a practical introduction to the Hole-Drilling Method, starting from its historical roots and going on to focus on its modern practice. The various chapters describe the nature of residual stresses, the principle of hole-drilling measurements, procedures and guidance on how to make successful measurements, and effective mathematical procedures for stress computation and analysis. The book is intended for practitioners who need to make residual stress measurements either occasionally or routinely, for practicing engineers, for researchers, and for graduate engineering and science students.

Download or read book A Contribution to Enlarge the Application Limits of Residual Stress Analyses by the Hole Drilling and the Ring Core Method written by Andreas Nau and published by kassel university press GmbH. This book was released on 2016-01-01 with total page 223 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation of the Blind Hole Drilling Method for the Measurement of Residual Stress written by C. S. Dentry and published by . This book was released on 1984 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: The blind hole drilling method has been employed to measure uniform residual stress fields; and an evaluation made of one approach to using this method when the stress field varies with depth. In particular stress fields generated by the application of uniaxial loads, by shot-peening and by heat treatment have been evaluated. The technique has been applied to the measurement of the residual stress field in the tyre bead seat region of a Boeing 727 main undercarriage wheel. This region has been found to have a significant level of residual stress perhaps indicative of the action of surface rolling.

Download or read book Comprehensive Materials Processing written by and published by Newnes. This book was released on 2014-04-07 with total page 5485 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive Materials Processing, Thirteen Volume Set provides students and professionals with a one-stop resource consolidating and enhancing the literature of the materials processing and manufacturing universe. It provides authoritative analysis of all processes, technologies, and techniques for converting industrial materials from a raw state into finished parts or products. Assisting scientists and engineers in the selection, design, and use of materials, whether in the lab or in industry, it matches the adaptive complexity of emergent materials and processing technologies. Extensive traditional article-level academic discussion of core theories and applications is supplemented by applied case studies and advanced multimedia features. Coverage encompasses the general categories of solidification, powder, deposition, and deformation processing, and includes discussion on plant and tool design, analysis and characterization of processing techniques, high-temperatures studies, and the influence of process scale on component characteristics and behavior. Authored and reviewed by world-class academic and industrial specialists in each subject field Practical tools such as integrated case studies, user-defined process schemata, and multimedia modeling and functionality Maximizes research efficiency by collating the most important and established information in one place with integrated applets linking to relevant outside sources

Download or read book Development of Digital Image Correlation Technique Applied to Hole Drilling Residual Stress Measurement written by and published by . This book was released on 2015 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt: The residual stresses found in components are mainly due to thermal, mechanical and metallurgical changes of material. The manufacturing processes such as fabrication, assembly, welding, rolling, heat treatment, shot peening etc. generate residual stresses in material. A significant number of improvements for residual stress measurement techniques have occurred in last few decades. The needs of Digital Image Correlation (DIC) techniques from industry have been increasing, especially in micro- and nano-scale mechanical testing applications mainly due to its relative easy implementation and utilization. In this dissertation, new experimental and numerical methods have been carried out, using a 3D-DIC measurement system with hole drilling operations and Finite Element Analysis (FEA) models to successfully predict both uniform and non-uniform residual stresses in material. The residual stresses have been calculated based on the established governing equations, 3D-DIC measured deformations, and calibration coefficients determined by finite element analyses. This 3D-DIC measurement technique performed in a no contact approach can capture the full-field, high sensitivity and high accuracy in-plan and out-of-plan deformation simultaneously. it can be used for both industrial and lab environments. There are three main categories for residual stress evaluations and validations in this dissertation. They are listed as following: 1) Through hole drilling (THD) on thin parts for uniform residual stresses; 2) Blind hole drilling (BHD) on thick parts for uniform residual tresses, where it is not possible to drill a through hole; 3) Incremental blind hole drilling (IBHD) on thick parts for non-uniform residual stresses which vary as a function of depth.

Download or read book Hole Drilling Method for Measuring Residual Stresses written by Gary S. Schajer and published by Morgan & Claypool Publishers. This book was released on 2018-01-22 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the theory and practice of the Hole-Drilling Method for measuring residual stresses in engineering components. Such measurements are important because residual stresses have a "hidden" character because they exist locked-in within a material, independent of any external load. These stresses are typically created during component manufacture, for example, during welding, casting, or forming. Because of their hidden nature, residual stresses are difficult to measure and consequently are often ignored. However, they directly add to loading stresses and can cause catastrophic failure if not properly included during engineering design. Thus, there is an urgent need to be able to identify and measure residual stresses conveniently and reliably. The Hole-Drilling Method provides an adaptable and well-proven method for measuring residual stresses in a wide range of materials and component types. It is convenient to use and gives reliable results. Because of the hidden nature of residual stresses, the measurement method must necessarily be indirect, thus, additional care and conceptual understanding are necessary to achieve successful results. This book provides a practical introduction to the Hole-Drilling Method, starting from its historical roots and going on to focus on its modern practice. The various chapters describe the nature of residual stresses, the principle of hole-drilling measurements, procedures and guidance on how to make successful measurements, and effective mathematical procedures for stress computation and analysis. The book is intended for practitioners who need to make residual stress measurements either occasionally or routinely, for practicing engineers, for researchers, and for graduate engineering and science students.

Download or read book A Summary of the Hole Drilling Method for Measuring Residual Stresses written by and published by . This book was released on 1981 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Measurement of residual stress using the centre hole drilling procedure written by B. L. Wotton and published by . This book was released on 1978 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Data Management for the Evaluation of Residual Stresses by the Incremental Hole drilling Method written by and published by . This book was released on 1994 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Evaluation of Four Hole Drilling Analysis Techniques with Respect to Non uniform Residual Stress Fields written by P.V Grant and published by . This book was released on 2002 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Development of the Deep Hole Drilling Method for Residual Stress Measurement in Metallic Welds written by Zheng Gang and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Residual Stresses 2016 written by Thomas M. Holden and published by Materials Research Forum LLC. This book was released on 2017-03-15 with total page 638 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the proceedings of the International Conference on Residual Stresses 10 and is devoted to the prediction/modelling, evaluation, control, and application of residual stresses in engineering materials. New developments, on stress-measurement techniques, on modelling and prediction of residual stresses and on progress made in the fundamental understanding of the relation between the state of residual stress and the material properties, are highlighted. The proceedings offer an overview of the current understanding of the role of residual stresses in materials used in wide ranging application areas.

Download or read book Residual Stresses 2018 written by Marc Seefeldt and published by Materials Research Forum LLC. This book was released on 2018-10-10 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: The European Conference on Residual Stresses (ECRS) series is the leading European forum for scientific exchange on internal and residual stresses in materials. It addresses both academic and industrial experts and covers a broad gamut of stress-related topics from instrumentation via experimental and modelling methodology up to stress problems in specific processes such as welding or shot-peening, and their impact on materials properties. Chapters: Diffraction Methods; Mechanical Relaxation Methods; Acoustic and Electromagnetic Methods; Composites, Nano and Microstructures; Films, Coatings and Oxides; Cold Working and Machining; Heat Treatments and Phase Transformations; Welding, Fatigue and Fracture: Stresses in Additive Manufacturing.

Download or read book Residual Stresses in Composite Materials written by Mahmood M. Shokrieh and published by Woodhead Publishing. This book was released on 2014-02-14 with total page 407 pages. Available in PDF, EPUB and Kindle. Book excerpt: Residual stresses are a common phenomenon in composite materials. They can either add to or significantly reduce material strength. Because of the increasing demand for high-strength, light-weight materials such as composites and their wide range of applications in the aerospace and automotive industries, in civil infrastructure and in sporting applications, it is critical that the residual stresses of composite materials are understood and measured correctly. The first part of this important book reviews destructive and non-destructive testing (NDT) techniques for measuring residual stresses. Various mathematical (analytical and numerical) methods for calculation of residual stresses in composite materials are also presented. Chapters in the first section of the book discuss the simulated hole drilling method, the slitting/crack compliance method, measuring residual stresses in homogeneous and composite glass materials using photoelastic techniques, and modeling residual stresses in composite materials. The second part of the book discusses residual stresses in polymer matrix, metal-matrix and a range of other types of composites. Moreover, the addition of nanoparticles to the matrix of polymeric composites as a new technique for reduction of residual stresses is discussed. Residual stresses in composite materials provides a comprehensive overview of this important topic, and is an invaluable reference text for both academics and professionals working in the mechanical engineering, civil engineering, aerospace, automotive, marine and sporting industries. Reviews destructive and non-destructive testing (NDT) techniques for measuring residual stresses Discusses residual stresses in polymer matrix, metal-matrix and other types of composite Considers the addition of nanoparticles to the matrix of polymeric composites as a new technique for reduction of residual stresses

Download or read book Residual Stress and Stress Relaxation written by Eric Kula and published by Springer Science & Business Media. This book was released on 2013-11-21 with total page 529 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Army Materials and Mechanics Research Center in coop eration with the Materials Science Group of the Department of Chemical Engineering and Materials Science of Syracuse University has been conducting the Annual Sagamore Army Materials Research Conference since 1954. The specific purpose of these conferences has been to bring together scientists and engineers from academic institutions, industry and government who are uniquely qualified to explore in depth a subject of importance to the Department of Defense, the Army and the scientific community. These proceedings, entitled RESIDUAL STRESS AND STRESS RELAXATION, address the nature of residual stresses and their measurements, the sources of residual stress, stress relaxation, sub-critical crack growth in the presence of residual stress, residual stresses and properties, and research in progress. We wish to acknowledge the assistance of Mr. Dan McNaught of the Army Materials and Mechanics Research Center and Mr. Robert J. Sell and Helen Brown DeMascio of Syracuse University throughout the stages of the conference planning and finally the publication of the book. The continued active interest and support of these conferences by Dr. E. Wright, Director of the Army Materials and Mechanics Research Center, is appreciated.

Download or read book International Conference on Residual Stresses written by G. Beck and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 1043 pages. Available in PDF, EPUB and Kindle. Book excerpt: Residual stresses are always introduced in materials when they are produced, or when they undergo non-uniform plastic deformation during use. The circumstances that can cause residual stresses are therefore numerous. Residual stresses exist in all materials and, depending on their distribution, can playa beneficial role (for example, compressive surface stress) or have a catastrophic effect, especially on fatigue behaviour and corrosion properties. The subject of residual stresses took form around 1970 with the development of methods to measure macroscopic deformations during the machining of materials or on an atomic scale by X-ray diffraction. These techniques have made considerable progress in the last 20 years. The meetings organized in several countries (Germany, France, Japan, etc. ) have largely contributed to this progress, aided by the numerous exchanges of information and knowledge to which they have given rise. Studies of the formation of residual stresses began more slowly, but have progressed with the emergence of increasingly realistic models of materials behaviour and with access to ever more powerful codes for numerical calculations. Two successive meetings for discussing this topic have been held in Europe. The first, held in 1982 in Nancy (France), consisted of 30 participants from 5 countries. The second was held in Linkoping (Sweden) in 1984, with 80 participants of 16 nationalities. It was decided to hold a first International Conference, ICRS, to address all aspects of the problem. Held in 1986 in Garmisch-Partenkirschen (FRG), it was an assembly of neady 300 participants from 21 countries.