Download or read book Feasibility of Introducing Particulate Filters on Gasoline Direct Injection Vehicles written by Athanasios Mamakos and published by . This book was released on 2011 with total page 81 pages. Available in PDF, EPUB and Kindle. Book excerpt: Starting from September 2011 a limit of 6x10 11 #/km will be introduced for the type approval of diesel passenger cars that will eventually apply to all new registered diesel passenger cars from September 2012. The same limit will also apply to diesel light duty vehicles but with a one year delay (09/2012 for type approvals and 09/2013 for all new registered vehicles). The regulation states that a Particle Number (PN) limit will also be introduced for the certification of Euro 6 technology gasoline-fuelled vehicles but the threshold value was not decided yet. While conventional Port Fuel Injection (PFI) gasoline vehicles can easily comply with the diesel limit, their Direct Injection (G-DI) counterparts are found to emit systematically above this threshold by up to 1 1/2 orders of magnitude. It is therefore expected that application of the diesel particle number limit to G-DI vehicles may necessitate the installation of particulate filters. At the same time, the penetration of G-DI vehicles is expected to rapidly grow in the near future in both the European and US markets. This is due to their improved fuel efficiency compared to the conventional PFIs, that would potentially provide the manufacturers the means to meet the target set in both EU and USA on the fleet-average carbon dioxide (CO2) emissions of future vehicles. It is foreseen that this vehicle category will dominate the gasoline market eventually replacing the conventional and less efficient PFI vehicles. There exist concerns however, that their elevated particulate emissions may adversely affect the air quality in the future if no measure is taken to efficiently control them. In this direction the present study examined the feasibility of introducing Gasoline Particulate Filters in G-DI vehicles and investigated the associated implementation cost and environmental benefit.

Download or read book Physical Characterization of Exhaust Particle Emissions from Late Technology Gasoline Vehicles written by Giorgio Martini and published by . This book was released on 2012 with total page 55 pages. Available in PDF, EPUB and Kindle. Book excerpt: The study assesses the feasibility of introducing the regulated particle number measurement procedure for the regulation of gasoline vehicles, focusing on the established cut-off size of 23 nm. A range of late technology gasoline vehicles were tested under regulated and unregulated test conditions. The results indicated a distinct emission behavior of Direct Injection Gasolines (G-DI), Port Fuel Injection gasolines (PFI) and Diesels equipped with Particulate Filters (DPF), that differed both in terms of the absolute levels but also with respect to the fraction of undetected nano-sized non-volatile particles. The latter was found to be around 20% (based on comparisons with a Condensation Particle Counter (CPC) having a 50% cut-off size at 4.5 nm) for three G-DI vehicles tested, but ranged between 40 and 70% for the two PFIs measured. Interestingly, a relatively large fraction of undetected nanosized was also observed for two late technology DPFs, ranging between 30 and 50%.^To a large extent these differences originate from differences in the size distributions and the relatively blunt shape of the counting efficiency curve of PMP compliant CPCs. Under conditions favouring nucleation mode formation in the dilution tunnel, excessive particle concentrations were detected by the low cut-off size CPCs, and especially the one with a d50 at 4.5 nm, that could exceed those of the PMP compliant CPC by up to one order of magnitude. However, the concentration of these nano-sized particles was found to decrease with increasing the dilution ratio in the first stage of the Volatile Particle Remover (VPR), indicating that this is rather a volatile artifact possibly originating from re-nucleation of evaporated material downstream of the VPR. The study also investigated the potential offered by a range of available approaches to effectively control particle emissions from G-DIs.^These included the use of a Gasoline Particulate Filter (GPF), the introduction of ethanol in the fuel but also an advanced engine concept combining port and direct fuel injection. The GPF system was found to very efficient in controlling particle number emissions under all driving conditions, having no visible impact on carbon dioxide emissions. The use of fuel with hi-ethanol content (75-85%) was also found to be beneficial especially at high engine loads (up to 97% reduction of nonvolatile particle numbers) and during cold start operation (up to 70% reduction). The tests with the "hybrid" G-DI-PFI vehicle indicated that there exists the potential for significant reduction of PM formation through engine measures. The non-volatile particle number emissions of this vehicle remained below the diesel limit over all hot start tests.

Download or read book Reducing Particulate Emissions in Gasoline Engines written by Thorsten Boger and published by SAE International. This book was released on 2018-11-28 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: For years, diesel engines have been the focus of particulate matter emission reductions. Now, however, modern diesel engines emit less particles than a comparable gasoline engine. This transformation necessitates an introduction of particulate reduction strategies for the gasoline-powered vehicle. Many strategies can be leveraged from diesel engines, but new combustion and engine control technologies will be needed to meet the latest gasoline regulations across the globe. Particulate reduction is a critical health concern in addition to the regulatory requirements. This is a vital issue with real-world implications. Reducing Particulate Emissions in Gasoline Engines encompasses the current strategies and technologies used to reduce particulates to meet regulatory requirements and curtail health hazards - reviewing principles and applications of these techniques. Highlights and features in the book include: Gasoline particulate filter design, function and applications Coated and uncoated three way catalyst design and integration Measurement of gasoline particulate matter emission, both laboratory and PEMS The goal is to provide a comprehensive assessment of gasoline particulate emission control to meet regulatory and health requirements - appealing to calibration, development and testing engineers alike.

Download or read book Nanoparticle Emissions From Combustion Engines written by Jerzy Merkisz and published by Springer. This book was released on 2015-03-19 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on particulate matter emissions produced by vehicles with combustion engines. It describes the physicochemical properties of the particulate matter, the mechanisms of its formation and its environmental impacts (including those on human beings). It discusses methods for measuring particulate mass and number, including the state-of-the-art in Portable Emission Measurement System (PEMS) equipment for measuring the exhaust emissions of both light and heavy-duty vehicles and buses under actual operating conditions. The book presents the authors’ latest investigations into the relations between particulate emission (mass and number) and engine operating parameters, as well as their new findings obtained through road tests performed on various types of vehicles, including those using diesel particulate filter regeneration. The book, which addresses the needs of academics and professionals alike, also discusses relevant European regulations on particulate emissions and highlights selected methods aimed at the reduction of particulate emissions from automobiles.

Download or read book Evaluation of a Gasoline Particulate Filter to Reduce Particle Emissions from a Gasoline Direct Injection Vehicle written by Tak W. Chan and published by . This book was released on 2012 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Encyclopedia of Automotive Engineering written by and published by John Wiley & Sons. This book was released on 2015-03-23 with total page 3888 pages. Available in PDF, EPUB and Kindle. Book excerpt: Erstmals eine umfassende und einheitliche Wissensbasis und Grundlage für weiterführende Studien und Forschung im Bereich der Automobiltechnik. Die Encyclopedia of Automotive Engineering ist die erste umfassende und einheitliche Wissensbasis dieses Fachgebiets und legt den Grundstein für weitere Studien und tiefgreifende Forschung. Weitreichende Querverweise und Suchfunktionen ermöglichen erstmals den zentralen Zugriff auf Detailinformationen zu bewährten Branchenstandards und -verfahren. Zusammenhängende Konzepte und Techniken aus Spezialbereichen lassen sich so einfacher verstehen. Neben traditionellen Themen des Fachgebiets beschäftigt sich diese Enzyklopädie auch mit "grünen" Technologien, dem Übergang von der Mechanik zur Elektronik und den Möglichkeiten zur Herstellung sicherer, effizienterer Fahrzeuge unter weltweit unterschiedlichen wirtschaftlichen Rahmenbedingungen. Das Referenzwerk behandelt neun Hauptbereiche: (1) Motoren: Grundlagen; (2) Motoren: Design; (3) Hybrid- und Elektroantriebe; (4) Getriebe- und Antriebssysteme; (5) Chassis-Systeme; (6) Elektrische und elektronische Systeme; (7) Karosserie-Design; (8) Materialien und Fertigung; (9) Telematik. - Zuverlässige Darstellung einer Vielzahl von Spezialthemen aus dem Bereich der Automobiltechnik. - Zugängliches Nachschlagewerk für Jungingenieure und Studenten, die die technologischen Grundlagen besser verstehen und ihre Kenntnisse erweitern möchten. - Wertvolle Verweise auf Detailinformationen und Forschungsergebnisse aus der technischen Literatur. - Entwickelt in Zusammenarbeit mit der FISITA, der Dachorganisation nationaler Automobil-Ingenieur-Verbände aus 37 Ländern und Vertretung von über 185.000 Ingenieuren aus der Branche. - Erhältlich als stets aktuelle Online-Ressource mit umfassenden Suchfunktionen oder als Print-Ausgabe in sechs Bänden mit über 4.000 Seiten. Ein wichtiges Nachschlagewerk für Bibliotheken und Informationszentren in der Industrie, bei Forschungs- und Schulungseinrichtungen, Fachgesellschaften, Regierungsbehörden und allen Ingenieurstudiengängen. Richtet sich an Fachingenieure und Techniker aus der Industrie, Studenten höherer Semester und Studienabsolventen, Forscher, Dozenten und Ausbilder, Branchenanalysen und Forscher.

Download or read book Automotive Spark Ignited Direct Injection Gasoline Engines written by F. Zhao and published by Elsevier. This book was released on 2000-02-08 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: The process of fuel injection, spray atomization and vaporization, charge cooling, mixture preparation and the control of in-cylinder air motion are all being actively researched and this work is reviewed in detail and analyzed. The new technologies such as high-pressure, common-rail, gasoline injection systems and swirl-atomizing gasoline fuel injections are discussed in detail, as these technologies, along with computer control capabilities, have enabled the current new examination of an old objective; the direct-injection, stratified-charge (DISC), gasoline engine. The prior work on DISC engines that is relevant to current GDI engine development is also reviewed and discussed. The fuel economy and emission data for actual engine configurations have been obtained and assembled for all of the available GDI literature, and are reviewed and discussed in detail. The types of GDI engines are arranged in four classifications of decreasing complexity, and the advantages and disadvantages of each class are noted and explained. Emphasis is placed upon consensus trends and conclusions that are evident when taken as a whole; thus the GDI researcher is informed regarding the degree to which engine volumetric efficiency and compression ratio can be increased under optimized conditions, and as to the extent to which unburned hydrocarbon (UBHC), NOx and particulate emissions can be minimized for specific combustion strategies. The critical area of GDI fuel injector deposits and the associated effect on spray geometry and engine performance degradation are reviewed, and important system guidelines for minimizing deposition rates and deposit effects are presented. The capabilities and limitations of emission control techniques and after treatment hardware are reviewed in depth, and a compilation and discussion of areas of consensus on attaining European, Japanese and North American emission standards presented. All known research, prototype and production GDI engines worldwide are reviewed as to performance, emissions and fuel economy advantages, and for areas requiring further development. The engine schematics, control diagrams and specifications are compiled, and the emission control strategies are illustrated and discussed. The influence of lean-NOx catalysts on the development of late-injection, stratified-charge GDI engines is reviewed, and the relative merits of lean-burn, homogeneous, direct-injection engines as an option requiring less control complexity are analyzed.

Download or read book Developing an Accelerated Aging System for Gasoline Particulate Filters and an Evaluation Test for Effects on Engine Performance written by James Eastman Jorgensen and published by . This book was released on 2014 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stringent regulations worldwide will limit the level of particulate matter (PM) emitted from gasoline engines equipped with direct fuel injection. Gasoline particulate filters (GPFs) present one strategy for meeting PM limits over the full operating range of the engine. Over time these filters accumulate incombustible ash, increasing system pressure drop and adversely effecting engine performance. The effect of aging as a result of ash accumulation is examined over the full lifetime of gasoline particulate filters, using a novel accelerated aging system. This system utilizes a gasoline combustion chamber into which lubricating oil is injected simulating combustion in the power cylinder - the primary source of lubricant-derived ash. Advanced imaging techniques are used to characterize filter and particulate emission behavior, and compare to prior data from diesel filters of the same type. Likewise, pressure drop behavior is observed for multiple filter samples and compared to prior experiments. A collocated Gasoline Direct Injection engine was installed for comparative purposes; a method of testing engine performance with GPF installations was developed and the engine was prepared and instrumented for future testing. This report details the construction and validation of the accelerated aging system, examination and comparison of results to those from prior experiments, and confirmation of principal assumptions used in developing the experimental test matrix. This study is one of a very few completed in a unique, emerging field of study, driven by new and extremely stringent emissions regulations around the globe. Practical testing here lays the foundation for future detailed research into the behavior and application of particulate filters to gasoline fueled engines in light duty passenger vehicles.

Download or read book Handbook of Advanced Ceramics written by and published by Academic Press. This book was released on 2013-04-11 with total page 1258 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new handbook will be an essential resource for ceramicists. It includes contributions from leading researchers around the world and includes sections on Basic Science of Advanced Ceramics, Functional Ceramics (electro-ceramics and optoelectro-ceramics) and engineering ceramics. Contributions from more than 50 leading researchers from around the world Covers basic science of advanced ceramics, functional ceramics (electro-ceramics and optoelectro-ceramics), and engineering ceramics Approximately 750 illustrations

Download or read book Future Powertrain Technologies written by Stephan Rinderknecht and published by MDPI. This book was released on 2020-12-17 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: Among the various factors greatly influencing the development process of future powertrain technologies, the trends in climate change and digitalization are of huge public interest. To handle these trends, new disruptive technologies are integrated into the development process. They open up space for diverse research which is distributed over the entire vehicle design process. This book contains recent research articles which incorporate results for selecting and designing powertrain topology in consideration of the vehicle operating strategy as well as results for handling the reliability of new powertrain components. The field of investigation spans from the identification of ecologically optimal transformation of the existent vehicle fleet to the development of machine learning-based operating strategies and the comparison of complex hybrid electric vehicle topologies to reduce CO2 emissions.

Download or read book Diesel Particulate Filter Technology written by Timothy V Johnson and published by SAE International. This book was released on 2007-03-28 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Until recently, the complexity of the Diesel Particulate Filter (DPF) system has hindered its commercial success. Stringent regulations of diesel emissions has lead to advancements in this technology, therefore mainstreaming the use of DPFs in light- and heavy-duty diesel filtration applications. This book covers the latest and most important research in DPF systems, focusing mainly on the advancements of the years 2002-2006. Editor Timothy V. Johnson selected the top 29 SAE papers covering the most significant research in this technology.

Download or read book Advances in Combustion of Gases Liquid Fuels Coal and Biomass written by Peter B. Sunderland and published by MDPI. This book was released on 2020-11-13 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue of Energies on “Advances in Combustion of Gases, Liquid Fuels, Coal and Biomass” includes five manuscripts on combustion research related to energy production. Both fundamental and applied research is included. The papers contain state-of-the-art experiments, computations, and theory. Combustion provides an estimated 85% of the world’s energy consumption. Advances in combustion research can benefit society in three main ways. Improving energy efficiency can reduce fuel consumption. Improving emissions can reduce climate change and adverse health effects. Improving fire and explosion safety can protect people, property, and the environment. The topical areas covered by this Special Issue are broad. It is hoped that this breadth will lead to a better understanding of combustion and improved diagnostic and numerical tools. This, in turn, may result in improved combustors, a cleaner environment, novel fuels, and improved safety and energy security.

Download or read book Diesel Particulate Filter Technology written by Timothy V Johnson and published by SAE International. This book was released on 2007-03-28 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Until recently, the complexity of the Diesel Particulate Filter (DPF) system has hindered its commercial success. Stringent regulations of diesel emissions has lead to advancements in this technology, therefore mainstreaming the use of DPFs in light- and heavy-duty diesel filtration applications. This book covers the latest and most important research in DPF systems, focusing mainly on the advancements of the years 2002-2006. Editor Timothy V. Johnson selected the top 29 SAE papers covering the most significant research in this technology.

Download or read book Particulate Matter Formation Mechanisms in a Direct injection Gasoline Engine written by Jared Cromas and published by . This book was released on 2003 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Fuels written by Barbara Elvers and published by John Wiley & Sons. This book was released on 2021-12-20 with total page 580 pages. Available in PDF, EPUB and Kindle. Book excerpt: A guide to industrially relevant products and processes for transportation fuels The Handbook of Fuels offers a comprehensive review of the wide variety of fuels used to power vehicles, aircraft and ships and examines the processes to produce these fuels. The updated second edition reflects the growing importance of fuels and fuel additives from renewable sources. New chapters include information on current production technology and use of bioethanol, biomethanol and biomass-to-liquid fuels. The book also reviews novel additives and performanace enhancers for conventional engines and fuels for novel bybrid engines. This comprehensive resource contains critical information on the legal, safety, and environmental issues associated with the production and use of fuels as well as reviewing important secondary aspects of the use and production of fuels. This authoritative guide includes contributions from authors who are long-standing contributors to the Ullmann's Encyclopedia, the world's most trusted reference for industrial chemistry. This important guide: Contains an updated edition of the authoritative resource to the production and use of fuels used for transportation Includes information that has been selected to reflect only commercially relevant products and processes Presents contributions from a team of noted experts in the field Offers the most recent developments in fuels and additives from renewable sources Written for professionals in the fields of fossil and renewable fuels, engine design, and transportation, Handbook of Fuels is the comprehensive resource that has been revised to reflect the recent developments in fuels used for transportation.

Download or read book Particulate Formation in Gasoline Direct Injection Engines written by and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Engine Exhaust Particulates written by Avinash Kumar Agarwal and published by Springer. This book was released on 2018-11-01 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comparative analysis of both diesel and gasoline engine particulates, and also of the emissions resulting from the use of alternative fuels. Written by respected experts, it offers comprehensive insights into motor vehicle particulates, their formation, composition, location, measurement, characterisation and toxicology. It also addresses exhaust-gas treatment and legal, measurement-related and technological advancements concerning emissions. The book will serve as a valuable resource for academic researchers and professional automotive engineers alike.