Download or read book Fault Diagnosis in Robotic and Industrial Systems written by Gerasimos G. Rigatos and published by Createspace Independent Pub. This book was released on 2012-11-01 with total page 210 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault detection and isolation is an important topic for researchers in the area of robotics and for industrial systems engineers. The need for a systematic method that will permit preventive maintenance through the diagnosis of incipient faults is obvious. At the same time it is desirable to reduce the false alarms rate so as to avoid unnecessary and costly interruptions of industrial processes and robotic tasks. The proposed book aims at analyzing recent advances in the area of fault diagnosis for robotic and industrial systems. There are totally 9 chapters in this book. Chapter 1 deals with supervision for the safe navigation of autonomous robots in a natural environment. Fault diagnosis and natural environment perception are used at different levels within a supervisor architecture and real operation is demonstrated on an autonomous tractor driving in an orchard. Chapter 2 gives an introduction to fault tolerant sensor systems which is based on the Failure Modes and Effects Analysis (FMEA) method. Chapter 3 aims at analyzing and implementing new solutions for the problem of distributed estimation for condition monitoring of nonlinear dynamical systems (e.g. automatic ground vehicles, unmanned surface or underwater vessels and unmanned aerial vehicles), so as to enable early detection of faults and the take up of efficient restoration measures. To this end, the development of distributed nonlinear state estimation and distributed fault detection and isolation (FDI) tools is proposed. Chapter 4 proposes so-called logic-dynamic approach for fault diagnosis in industrial systems described by nonlinear dynamic models with non-differentiable nonlinearities. The approach allows solving the problem of fault diagnosis is nonlinear systems using well-known linear methods. In Chapter 5, observer design for nonlinear systems described by a Takagi-Sugeno model with unmeasurable premise variables is proposed. Furthermore, a fault tolerant controller is proposed for such a system in order to preserve some performances of the system by trajectory tracking in faulty situations. Chapter 6 explains and demonstrates the utilization of different nonlinear-dynamics-based procedures for the purposes of structural health monitoring as well as for monitoring of robot joints based on Vibration-based Health Monitoring (VHM) methods In Chapter 7, vibrations picked from spalled defective rolling element bearings is presented. It uses a four stage processing algorithm to detect and diagnose the defective component in rolling element. In Chapter 8, the problem of fault diagnosis with parity equations is considered for nonlinear dynamic systems whose models are taken in the form of ordinary differential equations. The active and passive approaches are involved to achieve the robustness of the diagnostic procedure Finally, Chapter 9 proposes a graphical method for diagnosis of nonlinear systems. The proposed method is based on a 2D signature obtained by measurements projection over some moving time-window. This projection highlights what happens inside the system and enables the diagnosis of abnormal behaviors. This book is suitable for advanced undergraduate students and postgraduate students. It takes a practical approach rather than a conceptual approach. It offers a truly reader-friendly way to get to the subject related to the semantic web, making it the ideal resources for any student who is new to this subject and providing a definitive guide to anyone in this vibrant and evolving discipline. This book is an invaluable companion for students from their first encounter with the subject to more advanced studies, while the high quality artworks are designed to present the key concepts with simplicity, clarity and consistency.

Download or read book Fault Detection and Diagnosis in Industrial Systems written by L.H. Chiang and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: Early and accurate fault detection and diagnosis for modern chemical plants can minimize downtime, increase the safety of plant operations, and reduce manufacturing costs. This book presents the theoretical background and practical techniques for data-driven process monitoring. It demonstrates the application of all the data-driven process monitoring techniques to the Tennessee Eastman plant simulator, and looks at the strengths and weaknesses of each approach in detail. A plant simulator and problems allow readers to apply process monitoring techniques.

Download or read book Fault Diagnosis and Fault Tolerant Control of Robotic and Autonomous Systems written by Andrea Monteriù and published by Institution of Engineering and Technology. This book was released on 2020-08 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt: Robotic systems have experienced exponential growth thanks to their incredible adaptability. Modern robots require an increasing level of autonomy, safety and reliability. This book addresses the challenges of increasing and ensuring reliability and safety of modern robotic and autonomous systems. The book provides an overview of research in this field to-date, and addresses advanced topics including fault diagnosis and fault-tolerant control, and the challenging technologies and applications in industrial robotics, robotic manipulators, mobile robots, and autonomous and semi-autonomous vehicles.

Download or read book Modelling and Control for Intelligent Industrial Systems written by Gerasimos Rigatos and published by Springer Science & Business Media. This book was released on 2011-02-02 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: Incorporating intelligence in industrial systems can help to increase productivity, cut-off production costs, and to improve working conditions and safety in industrial environments. This need has resulted in the rapid development of modeling and control methods for industrial systems and robots, of fault detection and isolation methods for the prevention of critical situations in industrial work-cells and production plants, of optimization methods aiming at a more profitable functioning of industrial installations and robotic devices and of machine intelligence methods aiming at reducing human intervention in industrial systems operation. To this end, the book analyzes and extends some main directions of research in modeling and control for industrial systems. These are: (i) industrial robots, (ii) mobile robots and autonomous vehicles, (iii) adaptive and robust control of electromechanical systems, (iv) filtering and stochastic estimation for multisensor fusion and sensorless control of industrial systems (iv) fault detection and isolation in robotic and industrial systems, (v) optimization in industrial automation and robotic systems design, and (vi) machine intelligence for robots autonomy. The book will be a useful companion to engineers and researchers since it covers a wide spectrum of problems in the area of industrial systems. Moreover, the book is addressed to undergraduate and post-graduate students, as an upper-level course supplement of automatic control and robotics courses.

Download or read book Fault Diagnosis and Fault Tolerance for Mechatronic Systems Recent Advances written by Fabrizio Caccavale and published by Springer. This book was released on 2003-09-05 with total page 199 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will play a central role in ensuring safe and reliable behaviour of intelligent and autonomous systems. It collects some of the most recent results in fault diagnosis and fault tolerant systems, with particular emphasis on mechatronic systems.

Download or read book Fault Detection written by Fausto Pedro García Márquez and published by Nova Science Publishers. This book was released on 2014-02-11 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book synthesises the principles of fault detection with a focus on interfaces between the main disciplines of methods/technologies and industrial systems. It is complementary to other sub-disciplines such as maintenance, engineering, safety, risk analysis, etc. This book is intended for engineers, economists, technical consultants, researchers, etc. who are involved in the advancement of fault detection, and for those who incorporate fault detection in their work. The authors of this volume describe their pioneering work in the area and provide material from case studies that successfully applied the fault detection discipline in real life cases. Some topics discussed include condition monitoring of wind turbines; induction motor fault detection based on vibration analysis and support vector machines; failure detection and accommodation approaches for the airspeed sensor on a small UAV; and model-based fault diagnosis for industrial mobile robots.

Download or read book Intelligent Industrial Systems Modeling Automation and Adaptive Behavior written by Rigatos, Gerasimos and published by IGI Global. This book was released on 2010-06-30 with total page 601 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years, there has been growing interest in industrial systems, especially in robotic manipulators and mobile robot systems. As the cost of robots goes down and become more compact, the number of industrial applications of robotic systems increases. Moreover, there is need to design industrial systems with intelligence, autonomous decision making capabilities, and self-diagnosing properties. Intelligent Industrial Systems: Modeling, Automation and Adaptive Behavior analyzes current trends in industrial systems design, such as intelligent, industrial, and mobile robotics, complex electromechanical systems, fault diagnosis and avoidance of critical conditions, optimization, and adaptive behavior. This book discusses examples from major areas of research for engineers and researchers, providing an extensive background on robotics and industrial systems with intelligence, autonomy, and adaptive behavior giving emphasis to industrial systems design.

Download or read book Fault Diagnosis written by Józef Korbicz and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 936 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive work presents the status and likely development of fault diagnosis, an emerging discipline of modern control engineering. It covers fundamentals of model-based fault diagnosis in a wide context, providing a good introduction to the theoretical foundation and many basic approaches of fault detection.

Download or read book Fault Diagnosis and Detection written by Mustafa Demetgul and published by BoD – Books on Demand. This book was released on 2017-05-31 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mass production companies have become obliged to reduce their production costs and sell more products with lower profit margins in order to survive in competitive market conditions. The complexity and automation level of machinery are continuously growing. This development calls for some of the most critical issues that are reliability and dependability of automatic systems. In the future, machines will be monitored remotely, and computer-aided techniques will be employed to detect faults in the future, and also there will be unmanned factories where machines and systems communicate to each other, detect their own faults, and can remotely intercept their faults. The pioneer studies of such systems are fault diagnosis studies. Thus, we hope that this book will contribute to the literature in this regard.

Download or read book New Trends in Robot Control written by Jawhar Ghommam and published by Springer Nature. This book was released on 2020-02-13 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents solutions to control problems in a number of robotic systems and provides a wealth of worked-out examples with full analytical and numerical details, graphically illustrated to aid in reader comprehension. It also presents relevant studies on and applications of robotic system control approaches, as well as the latest findings from interdisciplinary theoretical studies. Featuring chapters on advanced control (fuzzy, neural, backstepping, sliding mode, adaptive, predictive, diagnosis, and fault-tolerant control), the book will equip readers to easily tailor the techniques to their own applications. Accordingly, it offers a valuable resource for researchers, engineers, and students in the field of robotic systems.

Download or read book Emergent Trends in Robotics and Intelligent Systems written by Peter Sinčák and published by Springer. This book was released on 2014-10-03 with total page 349 pages. Available in PDF, EPUB and Kindle. Book excerpt: What is the Role of Intelligent Technologies in the Next Generation of Robots ? This monograph gives answers to this question and presents emergent trends of Intelligent Systems and Robotics. After an introductory chapter celebrating 70 year of publishing the McCulloch Pitts model the book consists of the 2 parts „Robotics“ and „Intelligent Systems“. The aim of the book is to contribute to shift conventional robotics in which the robots perform repetitive, pre-programmed tasks to its intelligent form, where robots possess new cognitive skills with ability to learn and adapt to changing environment. A main focus is on Intelligent Systems, which show notable achievements in solving various problems in intelligent robotics. The book presents current trends and future directions bringing together Robotics and Computational Intelligence. The contributions include widespread experimental and theoretical results on intelligent robotics such as e.g. autonomous robotics, new robotic platforms, or talking robots.

Download or read book Diagnosis and Fault Tolerant Control written by Mogens Blanke and published by Springer. This book was released on 2015-08-11 with total page 701 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault-tolerant control aims at a gradual shutdown response in automated systems when faults occur. It satisfies the industrial demand for enhanced availability and safety, in contrast to traditional reactions to faults, which bring about sudden shutdowns and loss of availability. The book presents effective model-based analysis and design methods for fault diagnosis and fault-tolerant control. Architectural and structural models are used to analyse the propagation of the fault through the process, to test the fault detectability and to find the redundancies in the process that can be used to ensure fault tolerance. It also introduces design methods suitable for diagnostic systems and fault-tolerant controllers for continuous processes that are described by analytical models of discrete-event systems represented by automata. The book is suitable for engineering students, engineers in industry and researchers who wish to get an overview of the variety of approaches to process diagnosis and fault-tolerant control. The authors have extensive teaching experience with graduate and PhD students, as well as with industrial experts. Parts of this book have been used in courses for this audience. The authors give a comprehensive introduction to the main ideas of diagnosis and fault-tolerant control and present some of their most recent research achievements obtained together with their research groups in a close cooperation with European research projects. The third edition resulted from a major re-structuring and re-writing of the former edition, which has been used for a decade by numerous research groups. New material includes distributed diagnosis of continuous and discrete-event systems, methods for reconfigurability analysis, and extensions of the structural methods towards fault-tolerant control. The bibliographical notes at the end of all chapters have been up-dated. The chapters end with exercises to be used in lectures.

Download or read book Machine Learning Based Fault Diagnosis for Industrial Engineering Systems written by Rui Yang and published by CRC Press. This book was released on 2022-06-16 with total page 87 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides advanced techniques for precision compensation and fault diagnosis of precision motion systems and rotating machinery. Techniques and applications through experiments and case studies for intelligent precision compensation and fault diagnosis are offered along with the introduction of machine learning and deep learning methods. Machine Learning-Based Fault Diagnosis for Industrial Engineering Systems discusses how to formulate and solve precision compensation and fault diagnosis problems. The book includes experimental results on hardware equipment used as practical examples throughout the book. Machine learning and deep learning methods used in intelligent precision compensation and intelligent fault diagnosis are introduced. Applications to deal with relevant problems concerning CNC machining and rotating machinery in industrial engineering systems are provided in detail along with applications used in precision motion systems. Methods, applications, and concepts offered in this book can help all professional engineers and students across many areas of engineering and operations management that are involved in any part of Industry 4.0 transformation.

Download or read book Data Driven Fault Detection and Reasoning for Industrial Monitoring written by Jing Wang and published by Springer Nature. This book was released on 2022-01-03 with total page 277 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book assesses the potential of data-driven methods in industrial process monitoring engineering. The process modeling, fault detection, classification, isolation, and reasoning are studied in detail. These methods can be used to improve the safety and reliability of industrial processes. Fault diagnosis, including fault detection and reasoning, has attracted engineers and scientists from various fields such as control, machinery, mathematics, and automation engineering. Combining the diagnosis algorithms and application cases, this book establishes a basic framework for this topic and implements various statistical analysis methods for process monitoring. This book is intended for senior undergraduate and graduate students who are interested in fault diagnosis technology, researchers investigating automation and industrial security, professional practitioners and engineers working on engineering modeling and data processing applications. This is an open access book.

Download or read book Intelligent Fault Diagnosis and Accommodation Control written by Sunan Huang and published by CRC Press. This book was released on 2020-03-17 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt: Control systems include many components, such as transducers, sensors, actuators and mechanical parts. These components are required to be operated under some specific conditions. However, due to prolonged operations or harsh operating environment, the properties of these devices may degrade to an unacceptable level, causing more regular fault occurrences. It is therefore necessary to diagnose faults and provide the fault-accommodation control which compensates for the fault of the component by substituting a configuration of redundant elements so that the system continues to operate satisfactorily. In this book, we present a result of several years of work in the area of fault diagnosis and fault-accommodation control. It aims at information estimate methods when faults occur. The book uses the model built from the plant or process, to detect and isolate failures, in contrast to traditional hardware or statistical technologies dealing with failures. It presents model-based learning and design technologies for fault detection, isolation and identification as well as fault-tolerant control. These models are also used to analyse the fault detectability and isolability conditions and discuss the stability of the closed-loop system. It is intended to report new technologies in the area of fault diagnosis, covering fault analysis and control strategies of design for various applications. The book addresses four main schemes: modelling of actuator or sensor faults; fault detection and isolation; fault identification, and fault reconfiguration (accommodation) control. It also covers application issues in the monitoring control of actuators, providing several interesting case studies for more application-oriented readers.

Download or read book Advanced methods for fault diagnosis and fault tolerant control written by Steven X. Ding and published by Springer Nature. This book was released on 2020-11-24 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: The major objective of this book is to introduce advanced design and (online) optimization methods for fault diagnosis and fault-tolerant control from different aspects. Under the aspect of system types, fault diagnosis and fault-tolerant issues are dealt with for linear time-invariant and time-varying systems as well as for nonlinear and distributed (including networked) systems. From the methodological point of view, both model-based and data-driven schemes are investigated.To allow for a self-contained study and enable an easy implementation in real applications, the necessary knowledge as well as tools in mathematics and control theory are included in this book. The main results with the fault diagnosis and fault-tolerant schemes are presented in form of algorithms and demonstrated by means of benchmark case studies. The intended audience of this book are process and control engineers, engineering students and researchers with control engineering background.

Download or read book Simulation Modeling and Programming for Autonomous Robots written by Davide Brugali and published by Springer. This book was released on 2014-09-19 with total page 606 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the refereed proceedings of the 4th International Conference on Simulation, Modeling, and Programming for Autonomous Robots, SIMPAR 2014, held in Bergamo, Italy, in October 2014. The 49 revised full papers presented were carefully reviewed and selected from 62 submissions. The papers are organized in topical sections on simulation, modeling, programming, architectures, methods and tools, and systems and applications.