Download or read book Diagnosis and Fault Tolerant Control written by Mogens Blanke and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 583 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents model-based analysis and design methods for fault diagnosis and fault-tolerant control. Architectural and structural models are used to analyse the propagation of the fault through the process, test fault detectability and reveal redundancies that can be used to ensure fault tolerance. Case studies demonstrate the methods presented. The second edition includes new material on reconfigurable control, diagnosis of nonlinear systems, and remote diagnosis, plus new examples and updated bibliography.
Download or read book Fault Diagnosis and Fault Tolerant Control Strategies for Non Linear Systems written by Marcin Witczak and published by Springer Science & Business Media. This book was released on 2013-12-11 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents selected fault diagnosis and fault-tolerant control strategies for non-linear systems in a unified framework. In particular, starting from advanced state estimation strategies up to modern soft computing, the discrete-time description of the system is employed Part I of the book presents original research results regarding state estimation and neural networks for robust fault diagnosis. Part II is devoted to the presentation of integrated fault diagnosis and fault-tolerant systems. It starts with a general fault-tolerant control framework, which is then extended by introducing robustness with respect to various uncertainties. Finally, it is shown how to implement the proposed framework for fuzzy systems described by the well-known Takagi–Sugeno models. This research monograph is intended for researchers, engineers, and advanced postgraduate students in control and electrical engineering, computer science, as well as mechanical and chemical engineering.
Download or read book Fault Detection and Fault Tolerant Control for Nonlinear Systems written by Linlin Li and published by Springer. This book was released on 2016-02-19 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: Linlin Li addresses the analysis and design issues of observer-based FD and FTC for nonlinear systems. The author analyses the existence conditions for the nonlinear observer-based FD systems to gain a deeper insight into the construction of FD systems. Aided by the T-S fuzzy technique, she recommends different design schemes, among them the L_inf/L_2 type of FD systems. The derived FD and FTC approaches are verified by two benchmark processes.
Download or read book Fault Diagnosis and Fault tolerant Control in Nonlinear Systems written by Xiaodong Zhang and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault-tolerance is an essential property of many modern intelligent control systems. This dissertation presents a general framework for fault diagnosis and fault-tolerant control in nonlinear dynamical systems in the presence of possibly unstructured modeling uncertainty. The overall architecture is based on a learning approach, where the unknown fault is estimated using adaptive and on-line approximation techniques. First, the problem of fault detection and isolation in nonlinear uncertain systems is investigated. A novel fault isolation scheme is presented with its robustness and sensitivity properties enhanced by the use of adaptive thresholds in the residual evaluation stage. The fault isolation scheme is rigorously analyzed for its fault isolability condition and fault isolation time. Then we integrate the fault diagnosis (fault detection and isolation) scheme with fault-tolerant control design. Based on the fault information obtained during the diagnosis procedure, the system controller is reconfigured after fault detection and fault isolation, respectively, to compensate the effects of the fault. The closed-loop stability of the integrated fault-tolerant control system is established for different modes of the controlled plant. The effectiveness of the proposed fault diagnosis and fault-tolerant control scheme is illustrated via simulations in the three-tank system, a rigid-link robotic manipulator and the van der Pol oscillator system.
Download or read book Advanced methods for fault diagnosis and fault tolerant control written by Steven X. Ding and published by Springer Nature. This book was released on 2020-11-24 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: The major objective of this book is to introduce advanced design and (online) optimization methods for fault diagnosis and fault-tolerant control from different aspects. Under the aspect of system types, fault diagnosis and fault-tolerant issues are dealt with for linear time-invariant and time-varying systems as well as for nonlinear and distributed (including networked) systems. From the methodological point of view, both model-based and data-driven schemes are investigated.To allow for a self-contained study and enable an easy implementation in real applications, the necessary knowledge as well as tools in mathematics and control theory are included in this book. The main results with the fault diagnosis and fault-tolerant schemes are presented in form of algorithms and demonstrated by means of benchmark case studies. The intended audience of this book are process and control engineers, engineering students and researchers with control engineering background.
Download or read book Fault Diagnosis and Fault Tolerant Control Based on Adaptive Control Approach written by Qikun Shen and published by Springer. This book was released on 2017-02-14 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides recent theoretical developments in and practical applications of fault diagnosis and fault tolerant control for complex dynamical systems, including uncertain systems, linear and nonlinear systems. Combining adaptive control technique with other control methodologies, it investigates the problems of fault diagnosis and fault tolerant control for uncertain dynamic systems with or without time delay. As such, the book provides readers a solid understanding of fault diagnosis and fault tolerant control based on adaptive control technology. Given its depth and breadth, it is well suited for undergraduate and graduate courses on linear system theory, nonlinear system theory, fault diagnosis and fault tolerant control techniques. Further, it can be used as a reference source for academic research on fault diagnosis and fault tolerant control, and for postgraduates in the field of control theory and engineering.
Download or read book Fault Diagnosis written by Józef Korbicz and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 936 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive work presents the status and likely development of fault diagnosis, an emerging discipline of modern control engineering. It covers fundamentals of model-based fault diagnosis in a wide context, providing a good introduction to the theoretical foundation and many basic approaches of fault detection.
Download or read book Diagnosis and Fault tolerant Control Volume 2 written by Vicenc Puig and published by John Wiley & Sons. This book was released on 2021-12-29 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents recent advances in fault diagnosis and fault-tolerant control of dynamic processes. Its impetus derives from the need for an overview of the challenges of the fault diagnosis technique and sustainable control, especially for those demanding systems that require reliability, availability, maintainability, and safety to ensure efficient operations. Moreover, the need for a high degree of tolerance with respect to possible faults represents a further key point, primarily for complex systems, as modeling and control are inherently challenging, and maintenance is both expensive and safety-critical. Diagnosis and Fault-tolerant Control 2 also presents and compares different fault diagnosis and fault-tolerant schemes, using well established, innovative strategies for modeling the behavior of the dynamic process under investigation. An updated treatise of diagnosis and fault-tolerant control is addressed with the use of essential and advanced methods including signal-based, model-based and data-driven techniques. Another key feature is the application of these methods for dealing with robustness and reliability.
Download or read book Fault tolerant Control Systems written by Hassan Noura and published by Springer Science & Business Media. This book was released on 2009-07-30 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: The seriesAdvancesinIndustrialControl aims to report and encourage te- nologytransfer in controlengineering. The rapid development of controlte- nology has an impact on all areas of the control discipline. New theory, new controllers, actuators, sensors, new industrial processes, computer methods, new applications, new philosophies. . . , new challenges. Much of this devel- ment work resides in industrial reports, feasibility study papers, and the - ports of advanced collaborative projects. The series o?ers an opportunity for researchers to present an extended exposition of such new work in all aspects of industrial control for wider and rapid dissemination. Control system design and technology continues to develop in many d- ferent directions. One theme that the Advances in Industrial Control series is following is the application of nonlinear control design methods, and the series has some interesting new commissions in progress. However, another theme of interest is how to endow the industrial controller with the ability to overcome faults and process degradation. Fault detection and isolation is a broad ?eld with a research literature spanning several decades. This topic deals with three questions: • How is the presence of a fault detected? • What is the cause of the fault? • Where is it located? However, there has been less focus on the question of how to use the control system to accommodate and overcome the performance deterioration caused by the identi?ed sensor or actuator fault.
Download or read book Advanced methods for fault diagnosis and fault tolerant control written by Steven X. Ding and published by Springer. This book was released on 2020-11-24 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: The major objective of this book is to introduce advanced design and (online) optimization methods for fault diagnosis and fault-tolerant control from different aspects. Under the aspect of system types, fault diagnosis and fault-tolerant issues are dealt with for linear time-invariant and time-varying systems as well as for nonlinear and distributed (including networked) systems. From the methodological point of view, both model-based and data-driven schemes are investigated.To allow for a self-contained study and enable an easy implementation in real applications, the necessary knowledge as well as tools in mathematics and control theory are included in this book. The main results with the fault diagnosis and fault-tolerant schemes are presented in form of algorithms and demonstrated by means of benchmark case studies. The intended audience of this book are process and control engineers, engineering students and researchers with control engineering background.
Download or read book Reconfigurable Control of Nonlinear Dynamical Systems written by Jan H. Richter and published by Springer Science & Business Media. This book was released on 2011-01-16 with total page 299 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph summarizes solutions to reconfigurable fault-tolerant control problems for nonlinear dynamical systems that are based on the fault-hiding principle. It emphasizes but is not limited to complete actuator and sensor failures. In the first part, the monograph starts with a broad introduction of the control reconfiguration problems and objectives as well as summaries and explanations of solutions for linear dynamical systems. The solution is always a reconfiguration block, which consists of linear virtual actuators in the case of actuator faults and linear virtual sensors in the case of sensor faults. The main advantage of the fault-hiding concept is the reusability of the nominal controller, which remains in the loop as an active system while the virtual actuator and sensor adapt the control input and the measured output to the fault scenario. The second and third parts extend virtual actuators and virtual sensors towards the classes of Hammerstein-Wiener systems and piecewise affine systems. The main analyses concern stability recovery, setpoint tracking recovery, and performance recovery as reconfiguration objectives. The fourth part concludes the monograph with descriptions of practical implementations and case studies. The book is primarily intended for active researchers and practicing engineers in the field of fault-tolerant control. Due to many running examples it is also suitable for interested graduate students.
Download or read book Robust and Fault Tolerant Control written by Krzysztof Patan and published by Springer. This book was released on 2019-03-16 with total page 209 pages. Available in PDF, EPUB and Kindle. Book excerpt: Robust and Fault-Tolerant Control proposes novel automatic control strategies for nonlinear systems developed by means of artificial neural networks and pays special attention to robust and fault-tolerant approaches. The book discusses robustness and fault tolerance in the context of model predictive control, fault accommodation and reconfiguration, and iterative learning control strategies. Expanding on its theoretical deliberations the monograph includes many case studies demonstrating how the proposed approaches work in practice. The most important features of the book include: a comprehensive review of neural network architectures with possible applications in system modelling and control; a concise introduction to robust and fault-tolerant control; step-by-step presentation of the control approaches proposed; an abundance of case studies illustrating the important steps in designing robust and fault-tolerant control; and a large number of figures and tables facilitating the performance analysis of the control approaches described. The material presented in this book will be useful for researchers and engineers who wish to avoid spending excessive time in searching neural-network-based control solutions. It is written for electrical, computer science and automatic control engineers interested in control theory and their applications. This monograph will also interest postgraduate students engaged in self-study of nonlinear robust and fault-tolerant control.
Download or read book Diagnosis and Fault tolerant Control Volume 2 written by Vicenc Puig and published by John Wiley & Sons. This book was released on 2021-11-30 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents recent advances in fault diagnosis and fault-tolerant control of dynamic processes. Its impetus derives from the need for an overview of the challenges of the fault diagnosis technique and sustainable control, especially for those demanding systems that require reliability, availability, maintainability, and safety to ensure efficient operations. Moreover, the need for a high degree of tolerance with respect to possible faults represents a further key point, primarily for complex systems, as modeling and control are inherently challenging, and maintenance is both expensive and safety-critical. Diagnosis and Fault-tolerant Control 2 also presents and compares different fault diagnosis and fault-tolerant schemes, using well established, innovative strategies for modeling the behavior of the dynamic process under investigation. An updated treatise of diagnosis and fault-tolerant control is addressed with the use of essential and advanced methods including signal-based, model-based and data-driven techniques. Another key feature is the application of these methods for dealing with robustness and reliability.
Download or read book Fault Detection and Fault Tolerant Control Using Sliding Modes written by Halim Alwi and published by Springer Science & Business Media. This book was released on 2011-06-07 with total page 358 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault Detection and Fault-tolerant Control Using Sliding Modes is the first text dedicated to showing the latest developments in the use of sliding-mode concepts for fault detection and isolation (FDI) and fault-tolerant control in dynamical engineering systems. It begins with an introduction to the basic concepts of sliding modes to provide a background to the field. This is followed by chapters that describe the use and design of sliding-mode observers for FDI using robust fault reconstruction. The development of a class of sliding-mode observers is described from first principles through to the latest schemes that circumvent minimum-phase and relative-degree conditions. Recent developments have shown that the field of fault tolerant control is a natural application of the well-known robustness properties of sliding-mode control. A family of sliding-mode control designs incorporating control allocation, which can deal with actuator failures directly by exploiting redundancy, is presented. Various realistic case studies, specifically highlighting aircraft systems and including results from the implementation of these designs on a motion flight simulator, are described. A reference and guide for researchers in fault detection and fault-tolerant control, this book will also be of interest to graduate students working with nonlinear systems and with sliding modes in particular. Advances in Industrial Control aims to report and encourage the transfer of technology in control engineering. The rapid development of control technology has an impact on all areas of the control discipline. The series offers an opportunity for researchers to present an extended exposition of new work in all aspects of industrial control.
Download or read book Fault Tolerant Process Control written by Prashant Mhaskar and published by Springer Science & Business Media. This book was released on 2012-11-27 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault-Tolerant Process Control focuses on the development of general, yet practical, methods for the design of advanced fault-tolerant control systems; these ensure an efficient fault detection and a timely response to enhance fault recovery, prevent faults from propagating or developing into total failures, and reduce the risk of safety hazards. To this end, methods are presented for the design of advanced fault-tolerant control systems for chemical processes which explicitly deal with actuator/controller failures and sensor faults and data losses. Specifically, the book puts forward: · A framework for detection, isolation and diagnosis of actuator and sensor faults for nonlinear systems; · Controller reconfiguration and safe-parking-based fault-handling methodologies; · Integrated-data- and model-based fault-detection and isolation and fault-tolerant control methods; · Methods for handling sensor faults and data losses; and · Methods for monitoring the performance of low-level PID loops. The methodologies proposed employ nonlinear systems analysis, Lyapunov techniques, optimization, statistical methods and hybrid systems theory and are predicated upon the idea of integrating fault-detection, local feedback control, and supervisory control. The applicability and performance of the methods are demonstrated through a number of chemical process examples. Fault-Tolerant Process Control is a valuable resource for academic researchers, industrial practitioners as well as graduate students pursuing research in this area.
Download or read book Analysis and Synthesis of Fault Tolerant Control Systems written by Magdi S. Mahmoud and published by John Wiley & Sons. This book was released on 2013-10-28 with total page 451 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years, control systems have become more sophisticated in order to meet increased performance and safety requirements for modern technological systems. Engineers are becoming more aware that conventional feedback control design for a complex system may result in unsatisfactory performance, or even instability, in the event of malfunctions in actuators, sensors or other system components. In order to circumvent such weaknesses, new approaches to control system design have emerged which can tolerate component malfunctions while maintaining acceptable stability and performance. These types of control systems are often known as fault-tolerant control systems (FTCS). More precisely, FTCS are control systems which possess the ability to accommodate component failure automatically. Analysis and Synthesis of Fault-Tolerant Control Systems comprehensively covers the analysis and synthesis methods of fault tolerant control systems. It unifies the methods for developing controllers and filters for a wide class of dynamical systems and reports on the recent technical advances in design methodologies. MATLAB® is used throughout the book, to demonstrate methods of analysis and design. Key features: • Provides advanced theoretical methods and typical practical applications • Provides access to a spectrum of control design methods applied to industrial systems • Includes case studies and illustrative examples • Contains end-of-chapter problems Analysis and Synthesis of Fault-Tolerant Control Systems is a comprehensive reference for researchers and practitioners working in this area, and is also a valuable source of information for graduates and senior undergraduates in control, mechanical, aerospace, electrical and mechatronics engineering departments.
Download or read book Fault Diagnosis and Fault Tolerance for Mechatronic Systems Recent Advances written by Fabrizio Caccavale and published by Springer. This book was released on 2003-09-05 with total page 199 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will play a central role in ensuring safe and reliable behaviour of intelligent and autonomous systems. It collects some of the most recent results in fault diagnosis and fault tolerant systems, with particular emphasis on mechatronic systems.