Download or read book Fatigue Testing and Evaluation of Asphalt Binders Using the Dynamic Shear Rheometer written by A. Shenoy and published by . This book was released on 2002 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt: The dynamic shear rheometer (DSR) is being used currently by the asphalt pavement community for determination of the viscoelastic properties of asphalts following the recommendations of the Strategic Highway Research Program. The Superpave specification parameter |G*| sin? was identified as the term to be used in rating the asphalt binders for their fatigue resistance. However, in subsequent research work, it was found that this parameter did not relate well with the accumulation of fatigue damage of mixtures measured through a beam fatigue test under strain-controlled conditions. This led researchers to seek other methods of characterizing fatigue resistance behavior of asphalt binders. The suggested new test was a binder fatigue test using the time sweep on the DSR. The number of cycles to fatigue failure Nf was chosen as the criterion for rating the fatigue resistance of the binder.
Download or read book Fatigue of Asphalt Binders written by Wilfung Martono and published by . This book was released on 2008 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Binder Characterization and Evaluation written by David A. Anderson and published by Strategic Highway Research Program (Shrp). This book was released on 1994 with total page 504 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Understanding Mechanisms Leading to Asphalt Binder Fatigue written by and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue cracking is one of the primary modes of failure in asphalt pavements. Cracking typically occurs within the asphalt binder phase of asphalt mixtures. Thus, asphalt binder fatigue resistance is critical in determining overall pavement fatigue performance. One procedure commonly used to characterize asphalt binder fatigue resistance is the time sweep test, which consists of repeated torsional loading of a cylindrical specimen in the Dynamic Shear Rheometer (DSR). Generally, apparent changes in material properties with respect to number of cycles of loading are used to define fatigue failure of the asphalt binder. Results of this test have been shown to correlate well with asphalt mixture fatigue performance. However, the mechanisms responsible for changes in material properties during fatigue testing in the DSR were previously not well understood. Results in this study demonstrate that fracture can account for changes in loading resistance of asphalt binders during time sweep testing. Under cyclic torsional loading of cylindrical specimens, macro fracture is shown to manifest in the form of edge fracture. Edge fracture is a circumferential crack starting at the periphery of a cylindrical sample that propagates inward as loading is applied, reducing the effective sample size. Digital visualization of the fractured specimens allowed for determination of the fractured and intact sample area. Predictions of fracture propagation based on measurements of loading resistance and fracture mechanics concepts agreed favorably with actual measurements based on visualization. Furthermore, the fracture morphology and progression of crack growth of asphalt binders matched those observed for other materials under similar loading conditions. Based on these results, fatigue damage characterization of asphalt binders can be improved by incorporating fracture mechanics into an analysis framework for DSR fatigue test results. An analysis framework based on fracture principles is presented. The proposed model allows predicting fatigue life at any loading amplitude using the results of a single fatigue test. Additionally, it is demonstrated that time-temperature superposition is applicable to fatigue crack propagation of asphalt binders, allowing for efficient prediction of fatigue performance at multiple temperatures. The model is validated using a comparison between asphalt mixture and binder fatigue test results.
Download or read book Fracture Properties and Fatigue Cracking Resistance of Asphalt Binders written by Arash Motamed and published by . This book was released on 2012 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: Several different types of modifiers are increasingly being used to improve the performance of asphalt binders or to achieve desired mixture production characteristics (e.g., Warm Mix Asphalt). However, current Superpave performance specifications do not accurately reflect the performance characteristics of these modified binders. The main objective of this study was to evaluate the inherent fatigue cracking resistance of asphalt binders in the form of a matrix with rigid particle inclusions. The underlying rationale for this approach was to subject the binders to a state of stress that is similar to the one in a full asphalt mixture. This was achieved by fabricating and testing composite specimens of the asphalt binders and glass beads with a specified gradation. Four asphalt binders with similar true temperature grades but different modifiers were used in this study. The viscoelastic and fatigue cracking characteristics of the binders were measured using the glass bead-binder composite specimens in a dynamic shear rheometer at an intermediate temperature. The results demonstrate that the four asphalt binders modified using different methods had different damage characteristics despite the fact that these four binders were rated to have a similar performance grade based on the Superpave specifications. Fatigue cracking characteristics of the glass bead-binder test specimens used in this study were qualitatively very similar to the fatigue cracking characteristics of full asphalt mixtures using the same binders. The rank order of fatigue cracking resistance for the four glass bead-binder mixtures compared reasonably well to the rank order of fatigue cracking resistance for the full asphalt mixtures that incorporated these asphalt binders.
Download or read book PRO 28 6th International RILEM Symposium on Performance Testing and Evaluation of Bituminous Materials PTEBM 03 written by Manfred N. Partl and published by RILEM Publications. This book was released on 2003 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances in Interlaboratory Testing and Evaluation of Bituminous Materials written by Manfred N. Partl and published by Springer Science & Business Media. This book was released on 2012-10-17 with total page 465 pages. Available in PDF, EPUB and Kindle. Book excerpt: This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.
Download or read book 8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials written by Francesco Canestrari and published by Springer. This book was released on 2015-09-24 with total page 1024 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Recycling and re-use in road pavements This is the proceedings of the RILEM SIB2015 Symposium (Ancona, Italy, October 7-9, 2015).
Download or read book Evaluation of Healing in Asphalt Binders Using Dynamic Shear Rheometer and Molecular Modeling Techniques written by Ramamohan Reddy Bommavaram and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A self-healing material has the inherent ability to partially reverse damage such as crack formation that might have occurred during its service. Significant evidence exists in the literature to indicate that asphalt binder is a self-healing material. It is also well known that healing has a substantial affect on the performance of asphalt mixtures and consequently on the serviceable life of asphalt pavements. For example, shift factors from laboratory experimental data to field observed data show that laboratory data underpredict field observations. There is a need to understand the mechanisms that are responsible for healing in asphalt binders as well as to develop test methods that can be used to determine properties related to these mechanisms. This thesis presents details and findings from a two-part study that addresses each one of these two aspects. In the first part of this study, a test method based on the use of a Dynamic Shear Rheometer (DSR) was developed to determine the parameters of characteristic healing function of asphalt binders. In the second part of this study, Molecular Modeling (MM) techniques were used to determine the interrelationship between molecular structure, surface free energy, self diffusivity, and other healing properties of asphalt binders. The healing characteristic equation parameter (Ro) which represents the instantaneous healing nature of the asphalt binders is analogous to surface energy in terms of effect on healing in asphalt binders. Ro values for three asphalt binders AAM, AAD and ABD are calculated and compared with the surface energy values available from the literature. It was observed that the Ro values are proportional to surface energy values. Surface energy values for five asphalt binders AAM, AAD, AAB, AAG and AAF are calculated using MM method based on SHRP representative molecules. These values were observed to be proportional to the surface energy values from literature. Bulk and surface diffusion coefficients of asphalt molecules are calculated using MM method. Parametric analysis was done to determine the effect of chemical structure of asphalt on its diffusion properties. It was observed that the higher percentage of saturates in the chemical structure results into higher diffusion coefficients.
Download or read book Binder Characterization and Evaluation Test methods written by and published by . This book was released on 1994 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the 5th International Symposium on Asphalt Pavements Environment APE written by Marco Pasetto and published by Springer Nature. This book was released on 2019-08-29 with total page 503 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume highlights the latest advances, innovations, and applications in the field of asphalt pavement technology, as presented by leading international researchers and engineers at the 5th International Symposium on Asphalt Pavements & Environment (ISAP 2019 APE Symposium), held in Padua, Italy on September 11-13, 2019. It covers a diverse range of topics concerning materials and technologies for asphalt pavements, designed for sustainability and environmental compatibility: sustainable pavement materials, marginal materials for asphalt pavements, pavement structures, testing methods and performance, maintenance and management methods, urban heat island mitigation, energy harvesting, and Life Cycle Assessment. The contributions, which were selected by means of a rigorous international peer-review process, present a wealth of exciting ideas that will open novel research directions and foster multidisciplinary collaboration among different specialists.
Download or read book PRO 37 5th International RILEM Conference on Cracking in Pavements Mitigation Risk Assessment and Prevention written by C. Petit and published by RILEM Publications. This book was released on 2004 with total page 748 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Bituminous Mixtures and Pavements VII written by A.F. Nikolaides and published by CRC Press. This book was released on 2019-05-24 with total page 716 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highway engineers are facing the challenge not only to design and construct sustainable and safe pavements properly and economically. This implies a thorough understanding of materials behaviour, their appropriate use in the continuously changing environment, and implementation of constantly improved technologies and methodologies. Bituminous Mixtures and Pavements VII contains more than 100 contributions that were presented at the 7th International Conference ‘Bituminous Mixtures and Pavements’ (7ICONFBMP, Thessaloniki, Greece 12-14 June 2019). The papers cover a wide range of topics: - Bituminous binders - Aggregates, unbound layers and subgrade - Bituminous mixtures (Hot, Warm and Cold) - Pavements (Design, Construction, Maintenance, Sustainability, Energy and environment consideration) - Pavement management - Pavement recycling - Geosynthetics - Pavement assessment, surface characteristics and safety - Posters Bituminous Mixtures and Pavements VII reflects recent advances in highway materials technology and pavement engineering, and will be of interest to academics and professionals interested or involved in these areas.
Download or read book Transport Infrastructure and Systems written by Gianluca Dell'Acqua and published by CRC Press. This book was released on 2017-03-16 with total page 1134 pages. Available in PDF, EPUB and Kindle. Book excerpt: Transport Infrastructure Asset management in transport infrastructure, financial viability of transport engineering projects/ Life cycle Cost Analysis, Life-Cycle Assessment and Sustainability Assessment of transport infrastructure/ Infrastructures financing and pricing with equity appraisal, operation optimization and energy management/ Low-Volume roads: planning, maintenance, operations, environmental and social issues/ Public-Private Partnership (PPP) experience in transport infrastructure in different countries and economic conditions/ Airport Pavement Management Systems, runway design and maintenance/ Port maintenance and development issues, technology relating to cargo handling, landside access, cruise operations/ Infrastructure Building Information Modelling (I-BIM) / Pavement design and innovative bituminous materials/ Recycling and re-use in road pavements, environmentally sustainable technologies/ Stone pavements, ancient roads and historic railways/ Cementitious stabilization of materials used in the rehabilitation of transportation infrastructure. Transport Systems Sustainable transport and the environment protection including green vehicles/ Urban transport, land use development, spatial and transport planning/ Bicycling, bike, bike-sharing systems, cycling mobility/ Human factor in transport systems/ Intelligent Mobility: emerging technologies to enable the smarter movement of people and goods/Airport landside: access roads, parking facilities, terminal facilities, aircraft apron and the azdjacent taxiway/ Transportation policy, planning and design, modelling and decision making/ Transport economics, finance and pricing issues, optimization problems, equity appraisal/ Road safety impact assessments, road safety audits, the management of road network safety and safety inspections/ Tunnels and underground structures: preventing incidents-accidents mitigating their effects for both people and goods/ Traffic flow characteristics, traffic control devices, work zone traffic control, highway capacity and quality of service/ Track-vehicle interactions in railway systems, capacity analysis of railway networks/ Risk assessment and safety in air and railway transport, reliability aspects/ Maritime transport and inland waterways transport research/ Intermodal freight transport: terminals and logistics.
Download or read book Advances in Interlaboratory Testing and Evaluation of Bituminous Materials written by Manfred N. Partl and published by Springer Science & Business Media. This book was released on 2012-10-17 with total page 453 pages. Available in PDF, EPUB and Kindle. Book excerpt: This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.
Download or read book Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer DSR written by and published by . This book was released on with total page 31 pages. Available in PDF, EPUB and Kindle. Book excerpt: This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binder when tested in dynamic (oscillatory) shear using parallel plate test geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 6 and 88°C at an angular frequency of 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binder. This standard is appropriate for unaged material or material aged in accordance with T 240 and R 28.
Download or read book Proceedings of the RILEM International Symposium on Bituminous Materials written by Hervé Di Benedetto and published by Springer Nature. This book was released on 2021-09-25 with total page 1806 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume highlights the latest advances, innovations, and applications in bituminous materials and structures and asphalt pavement technology, as presented by leading international researchers and engineers at the RILEM International Symposium on Bituminous Materials (ISBM), held in Lyon, France on December 14-16, 2020. The symposium represents a joint effort of three RILEM Technical Committees from Cluster F: 264-RAP “Asphalt Pavement Recycling”, 272-PIM “Phase and Interphase Behaviour of Bituminous Materials”, and 278-CHA “Crack-Healing of Asphalt Pavement Materials”. It covers a diverse range of topics concerning bituminous materials (bitumen, mastics, mixtures) and road, railway and airport pavement structures, including: recycling, phase and interphase behaviour, cracking and healing, modification and innovative materials, durability and environmental aspects, testing and modelling, multi-scale properties, surface characteristics, structure performance, modelling and design, non-destructive testing, back-analysis, and Life Cycle Assessment. The contributions, which were selected by means of a rigorous international peer-review process, present a wealth of exciting ideas that will open novel research directions and foster new multidisciplinary collaborations.
