Download or read book Fatigue of Heavy Vehicle Engine Materials written by Viktor Norman and published by Linköping University Electronic Press. This book was released on 2018-02-13 with total page 49 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to increasing demands on sustainability exerted by end-costumers and policy makers, heavyvehicle manufacturers are urged to increase the engine efficiency in order to reduce the exhaust gas emission. However, increasing the efficiency is also associated with an elevated fatigue rate of the materials constituting the engine parts, which consequently reduces the engine service life. The aim of the present thesis is therefore to confront the expected increase by studying the fatigue behaviour and damage mechanisms of the materials typically employed in heavy-vehicle diesel engines. With this knowledge, this work seeks to guide the development of new heavy-vehicle engine materials, as well as to develop improved life estimation methods designated to assist the mechanical design of durable heavy-vehicle engines. In essence, a large set of thermo-mechanical fatigue (TMF) and combined thermomechanical and high-cycle fatigue (TMF-HCF) tests is conducted at engine load conditions on laboratory specimens of lamellar, compacted and spheroidal graphite iron. In this way, the fatigue performance and associated damage mechanisms are investigated. In particular, a new fatigue property is identified, the TMF-HCF threshold, which quantifies how resistant a material is to superimposed high-cycle fatigue. The damage mechanism at low temperatures (?500°C) is confirmed to consist of the initiation, propagation and coalescence of numerous microcracks. Based on this, a successful fatigue life estimation model is formulated, allowing accurate estimations of TMF and TMF-HCF tests on smooth specimens, and TMF tests on notched specimens. In the latter case, the microcrack growth behaviour in non-uniform cyclic stress fields and its implications for life estimation are clarified. At elevated temperatures (?500°C), surface oxidation is shown to govern the fatigue performance of cast iron grades intended for exhaust manifolds. It is observed that oxide intrusions are induced, from which surface fatigue cracks are initiated. Consequently, an optimal material at these conditions should have a low oxide growth rate and few casting defects at the surface, as these factors are found to stimulate the growth of intrusion.
Download or read book Fatigue of Heavy vehicle Engine Materials written by Viktor Norman and published by . This book was released on 2018 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to increasing demands on sustainability exerted by end-costumers and policy makers, heavy-vehicle manufacturers are urged to increase the engine efficiency in order to reduce the exhaust gas emission. However, increasing the efficiency is also associated with an elevated fatigue rate of the materials constituting the engine parts, which consequently reduces the engine service life. The aim of the present thesis is therefore to confront the expected increase by studying the fatigue behaviour and damage mechanisms of the materials typically employed in heavy-vehicle diesel engines. With this knowledge, this work seeks to guide the development of new heavy-vehicle engine materials, as well as to develop improved life estimation methods designated to assist the mechanical design of durable heavy-vehicle engines. In essence, a large set of thermo-mechanical fatigue (TMF) and combined thermo-mechanical and high-cycle fatigue (TMF-HCF) tests is conducted at engine load conditions on laboratory specimens of lamellar, compacted and spheroidal graphite iron. In this way, the fatigue performance and associated damage mechanisms are investigated. In particular, a new fatigue property is identified, the TMF-HCF threshold, which quantifies how resistant a material is to superimposed high-cycle fatigue. The damage mechanism at low temperatures (/ 500oC) is confirmed to consist of the initiation, propagation and coalescence of numerous microcracks. Based on this, a successful fatigue life estimation model is formulated, allowing accurate estimations of TMF and TMF-HCF tests on smooth specimens, and TMF tests on notched specimens. In the latter case, the microcrack growth behaviour in non-uniform cyclic stress fields and its implications for life estimation are clarified. At elevated temperatures (' 500oC), surface oxidation is shown to govern the fatigue performance of cast iron grades intended for exhaust manifolds. It is observed that oxide intrusions are induced, from which surface fatigue cracks are initiated. Consequently, an optimal material at these conditions should have a low oxide growth rate and few casting defects at the surface, as these factors are found to stimulate the growth of intrusion.
Download or read book Fatigue of Heavy Vehicle Engine Materials written by and published by . This book was released on 2015 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Critical Component Wear in Heavy Duty Engines written by P. A. Lakshminarayanan and published by John Wiley & Sons. This book was released on 2011-09-07 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: The critical parts of a heavy duty engine are theoretically designed for infinite life without mechanical fatigue failure. Yet the life of an engine is in reality determined by wear of the critical parts. Even if an engine is designed and built to have normal wear life, abnormal wear takes place either due to special working conditions or increased loading. Understanding abnormal and normal wear enables the engineer to control the external conditions leading to premature wear, or to design the critical parts that have longer wear life and hence lower costs. The literature on wear phenomenon related to engines is scattered in numerous periodicals and books. For the first time, Lakshminarayanan and Nayak bring the tribological aspects of different critical engine components together in one volume, covering key components like the liner, piston, rings, valve, valve train and bearings, with methods to identify and quantify wear. The first book to combine solutions to critical component wear in one volume Presents real world case studies with suitable mathematical models for earth movers, power generators, and sea going vessels Includes material from researchers at Schaeffer Manufacturing (USA), Tekniker (Spain), Fuchs (Germany), BAM (Germany), Kirloskar Oil Engines Ltd (India) and Tarabusi (Spain) Wear simulations and calculations included in the appendices Instructor presentations slides with book figures available from the companion site Critical Component Wear in Heavy Duty Engines is aimed at postgraduates in automotive engineering, engine design, tribology, combustion and practitioners involved in engine R&D for applications such as commercial vehicles, cars, stationary engines (for generators, pumps, etc.), boats and ships. This book is also a key reference for senior undergraduates looking to move onto advanced study in the above topics, consultants and product mangers in industry, as well as engineers involved in design of furnaces, gas turbines, and rocket combustion. Companion website for the book: www.wiley.com/go/lakshmi
Download or read book Commercial Motor Vehicle Driver Fatigue Long Term Health and Highway Safety written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2016-09-12 with total page 273 pages. Available in PDF, EPUB and Kindle. Book excerpt: There are approximately 4,000 fatalities in crashes involving trucks and buses in the United States each year. Though estimates are wide-ranging, possibly 10 to 20 percent of these crashes might have involved fatigued drivers. The stresses associated with their particular jobs (irregular schedules, etc.) and the lifestyle that many truck and bus drivers lead, puts them at substantial risk for insufficient sleep and for developing short- and long-term health problems. Commercial Motor Vehicle Driver Fatigue, Long-Term Health and Highway Safety assesses the state of knowledge about the relationship of such factors as hours of driving, hours on duty, and periods of rest to the fatigue experienced by truck and bus drivers while driving and the implications for the safe operation of their vehicles. This report evaluates the relationship of these factors to drivers' health over the longer term, and identifies improvements in data and research methods that can lead to better understanding in both areas.
Download or read book Fatigue of Metallic Materials written by M. Klesnil and published by Elsevier. This book was released on 1992-04-13 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews problems in the mechanical behaviour of cyclically loaded metallic materials, primarily with regard to the nature of the fatigue process. The first edition of the book appeared in 1980. The present second edition represents a revised form of the original book and also covers recent developments in the field. As the book focuses on physical-metallurgical aspects, it occupies a unique and important position in the technical literature, which has so far been devoted mainly to engineering metal fatigue problems and their technical solution in specific practical cases. The book provides a compact review of current knowledge on physical metallurgical processes that accompany and affect the fatigue of metallic materials, and also presents the background for applying the new results to practical designing and to the selection of materials in engineering practice. The authors present an updated review of results from countries both in the east and the west and cover a relatively large field in a concise manner. The work will be of value to research workers and students following advanced and post-graduate courses in the fields of materials science and mechanical engineering.
Download or read book Heavy Vehicle Technology written by D. J. Leeming and published by Nelson Thornes. This book was released on 1981 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text is well established as one of the most autoritative textbooks in the truck and bus industry, having been read by many students and adopted by college lecturers at home & overseas.
Download or read book Fatigue and Durability of Structural Materials written by Gary R. Halford and published by ASM International. This book was released on 2006 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue and Durability of Structural Materials explains how mechanical material behavior relates to the design of structural machine components. The major emphasis is on fatigue and failure behavior using engineering models that have been developed to predict, in advance of service, acceptable fatigue and other durability-related lifetimes. The book covers broad classes of materials used for high-performance structural applications such as aerospace components, automobiles, and power generation systems. Coverage focuses on metallic materials but also addresses unique capabilities of important nonmetals. The concepts are applied to behavior at room or ambient temperatures; a planned second volume will address behavior at higher-temperatures. The volume is a repository of the most significant contributions by the authors to the art and science of material and structural durability over the past half century. During their careers, including 40 years of direct collaboration, they have developed a host of durability models that are based on sound physical and engineering principles. Yet, the models and interpretation of behavior have a unique simplicity that is appreciated by the practicing engineer as well as the beginning student. In addition to their own pioneering work, the authors also present the work of numerous others who have provided useful results that have moved progress in these fields. This book will be of immense value to practicing mechanical and materials engineers and designers charged with producing structural components with adequate durability. The coverage is appropriate for a range of technical levels from undergraduate engineering students through material behavior researchers and model developers. It will be of interest to personnel in the automotive and off-highway vehicle manufacturing industry, the aeronautical industry, space propulsion and the power generation/conversion industry, the electric power industry, the machine tool industry, and any industry associated with the design and manufacturing of mechanical equipment subject to cyclic loads.
Download or read book High Cycle Fatigue written by Theodore Nicholas and published by Elsevier. This book was released on 2006-07-07 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dr Theodore Nicholas ran the High Cycle Fatigue Program for the US Air Force between 1995 and 2003 at Wright-Patterson Air Force Base, and is one of the world’s leading authorities on the subject, having authored over 250 papers in leading archival journals and books. Bringing his plethora of expertise to this book, Dr Nicholas discusses the subject of high cycle fatigue (HCF) from an engineering viewpoint in response to a series of HCF failures in the USAF and the concurrent realization that HCF failures in general were taking place universally in both civilian and military engines. Topic covered include: Constant life diagrams Fatigue limits under combined LCF and HCF Notch fatigue under HCF conditions Foreign object damage (FOD) Brings years of the Author's US Air Force experience in high cycle fatigue together in one text Discusses HCF in the context of recent international military and civilian engine failures
Download or read book Materials fatigue Testing of Vehicle Components Systems written by Carlos L. R. Storniolo and published by . This book was released on 1993 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue of Metals written by P. G. Forrest and published by Elsevier. This book was released on 2013-10-22 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue of Metals provides a general account of the failure of metals due to fatigue, a subject of great practical importance in the field of engineering and metallurgy. The book covers a wide range of topics on the study of the fatigue of metals. The text presents in the first three chapters the characteristics and detection of fatigue fractures; methods of fatigue testing; and the fatigue strengths of different materials. The resistance of materials to fatigue under complex stress; the determination and effects of stress concentration; influence of surface treatment on fatigue strength; and effects of corrosion and temperature are also studied in detail. In relation to the previous chapters of fatigue information, a chapter is devoted to engineering design to prevent fatigue. The last two chapters provide a brief historical survey of the developments of the study of the mechanism of fatigue and fatigue of non-metallic materials such as wood, plastic, rubber, glass, and concrete. Mechanical engineers, designers, metallurgists, researchers, and students will find the book as a good reference material.
Download or read book Introduction to Fatigue in Metals and Composites written by R.L. Carlson and published by Springer Science & Business Media. This book was released on 1995-11-30 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to Fatigue in Metals and Composites provides a balanced treatment of the phenomenon of fatigue in metals, nonmetals and composites with polymeric, metallic and ceramic matrices. The applicability of the safe life philosophy of design is examined for each of the materials. Attention is also focused on the stable crack growth phase of fatigue and differences in the operative mechanisms for the various classes of materials are considered. The impacts of these differences on the development of damage tolerance strategies are examined. Among topics discussed are; variable amplitude loading with tensile and compressive overload; closure obstruction; bridging mechanisms; mixed mode states; small cracks; delamination mechanisms and environmental conditions. The arrangement and presentation of the topics are such that An Introduction to Fatigue in Metals and Composites can serve as a course text for mechanical, civil, aeronautical and astronautical engineering and material science courses as well as a reference for engineers who are concerned with fatigue testing and aircraft, automobile and engine design.
Download or read book Light and Heavy Vehicle Technology written by Malcolm James Nunney and published by Routledge. This book was released on 2007 with total page 685 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition contains new material covering the latest development in electronics, alternative fuels, emissions and diesel systems.
Download or read book Testing Automotive Materials and Components written by Don H. Wright and published by SAE International. This book was released on 1993 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: Testing Automotive Materials and Components shows how automotive materials and components can be evaluated to reveal their true characteristics under realistic loading and environmental conditions. The book describes and illustrates test methods which will help designers and development engineers save valuable time and expenditure, not only during the prototype and pre- production stages, but in the event of service failure. Chapters cover: types of specimen; service failure analysis; basic fatigue testing; realistic fatigue testing; effect of speed and accelerated dynamic testing; crankshafts and connecting rods; cams and followers; axle shafts, driver shafts and torsion bars; gears; road wheels; and plastics, composites and ceramics.
Download or read book The Fatigue of Metals written by Herbert John Gough and published by . This book was released on 1924 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Engine Failure Analysis written by Ernst Greuter and published by SAE International. This book was released on 2012-06-12 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engine failures result from a complex set of conditions, effects, and situations. To understand why engines fail and remedy those failures, one must understand how engine components are designed and manufactured, how they function, and how they interact with other engine components. To this end, this book examines how engine components are designed and how they function, along with their physical and technical properties. Translated from a popular German reference work, this English edition sheds light on determining engine failure and remedies. The authors present a selection of engine failures, investigate and evaluate why they failed, and provide guidance on how to prevent such failures. A large range of possible engine failures is presented in a comprehensive, readily understandable manner, free of manufacturer bias. The scope of engines covered includes general-purpose engines found in heavy commercial vehicles, railway locomotives and vehicles, electrical generators, prime movers, and marine engines. Such engines are technical precursors to automotive engines. This book is for all who deal with engine failures: those who work in repair shops, shipyards, engineering consultancies, insurance companies and technical oversight organizations, as well as R&D departments at engine and component manufacturers. Researchers, academics, and students will learn how even the theoretically impossible can-and will-happen.
Download or read book Thermomechanical Fatigue Behavior of Materials written by Michael A. McGaw and published by ASTM International. This book was released on 2003 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: "ASTM Stock Number: STP1428. - "Fourth Symposium on Thermomechanical Fatigue Behavior of Materials, held in Dallas, Texas on November 7-8, 2001. The Symposium was sponsored by ASTM Committee E08 on Fatigue and Fracture and its Subcommittee E08.05 on Cyclic Deformation and Fat. - Includes bibliographical references and indexes. ASTM International; 2011.
