Download or read book Fatigue Life Prediction of Welded Components Based on Fracture Mechanics written by MH. El Haddad and published by . This book was released on 1980 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt: An elastic-plastic fracture mechanics solution for fatigue cracks initiating from weld toes is introduced that admits plasticity by replacing the conventional stress term with a strain term. It accounts for the propagation of very short cracks by the introduction of an effective crack length equal to the actual length increased by an amount l0, where l0 is a constant characteristic of the material and material condition. Consideration is also given to the effect of mean stress and crack front shape on an intensity factor derived from this solution. Crack growth results for cracks in both elastic and plastic strain fields of welded specimens, when interpreted in terms of the intensity factor, show excellent agreement with elastic long crack data. This intensity factor, when combined with a propagation model that includes all stages of crack growth, also successfully predicts the entire life of butt- and fillet-welded specimens for two steels. The threshold stress corresponding to the failure of butt-welded specimens is equal to the smooth specimen fatigue limit stress divided by the elastic stress concentration factor. However, for fillet welds, the stress level corresponding to failure is higher than the fatigue limit stress divided by the elastic stress concentration factor. At stresses between these two stress levels, cracks start at fillet-weld toes but do not propagate to failure.
Download or read book Fatigue Life Analyses of Welded Structures written by Tom Lassen and published by John Wiley & Sons. This book was released on 2013-03-01 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Avoiding or controlling fatigue damage is a major issue in the design and inspection of welded structures subjected to dynamic loading. Life predictions are usually used for safe life analysis, i.e. for verifying that it is very unlikely that fatigue damage will occur during the target service life of a structure. Damage tolerance analysis is used for predicting the behavior of a fatigue crack and for planning of in-service scheduled inspections. It should be a high probability that any cracks appearing are detected and repaired before they become critical. In both safe life analysis and the damage tolerance analysis there may be large uncertainties involved that have to be treated in a logical and consistent manner by stochastic modeling. This book focuses on fatigue life predictions and damage tolerance analysis of welded joints and is divided into three parts. The first part outlines the common practice used for safe life and damage tolerance analysis with reference to rules and regulations. The second part emphasises stochastic modeling and decision-making under uncertainty, while the final part is devoted to recent advances within fatigue research on welded joints. Industrial examples that are included are mainly dealing with offshore steel structures. Spreadsheets which accompany the book give the reader the possibility for hands-on experience of fatigue life predictions, crack growth analysis and inspection planning. As such, these different areas will be of use to engineers and researchers.
Download or read book Fracture and Fatigue of Welded Joints and Structures written by K Macdonald and published by Elsevier. This book was released on 2011-04-19 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: The failure of any welded joint is at best inconvenient and at worst can lead to catastrophic accidents. Fracture and fatigue of welded joints and structures analyses the processes and causes of fracture and fatigue, focusing on how the failure of welded joints and structures can be predicted and minimised in the design process.Part one concentrates on analysing fracture of welded joints and structures, with chapters on constraint-based fracture mechanics for predicting joint failure, fracture assessment methods and the use of fracture mechanics in the fatigue analysis of welded joints. In part two, the emphasis shifts to fatigue, and chapters focus on a variety of aspects of fatigue analysis including assessment of local stresses in welded joints, fatigue design rules for welded structures, k-nodes for offshore structures and modelling residual stresses in predicting the service life of structures.With its distinguished editor and international team of contributors, Fracture and fatigue of welded joints and structures is an essential reference for mechanical, structural and welding engineers, as well as those in the academic sector with a research interest in the field. - Analyses the processes and causes of fracture and fatigue, focusing predicting and minimising the failure of welded joints in the design process - Assesses the fracture of welded joints and structure featuring constraint-based fracture mechanics for predicting joint failure - Explores specific considerations in fatigue analysis including the assessment of local stresses in welded joints and fatigue design rules for welded structures
Download or read book Fatigue Life Prediction of Welded Joints Based on Fracture Mechanics and Crack Closure written by Jan Behrendt Ibsø and published by . This book was released on 1995 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Strength of Welded Structures written by S J Maddox and published by Woodhead Publishing. This book was released on 2014-03-14 with total page 211 pages. Available in PDF, EPUB and Kindle. Book excerpt: The key to avoidance of fatigue, which is the main cause of service failures, is good design. In the case of welded joints, which are particularly susceptible to fatigue, design rules are available. However, their effective use requires a good understanding of fatigue and an appreciation of problems concerned with their practical application. Fatigue strength of welded structures has incorporates up-to-date design rules with high academic standards whilst still achieving a practical approach to the subject. The book presents design recommendations which are based largely on those contained in recent British standards and explains how they are applied in practice. Attention is also focused on the relevant aspects of fatigue in welded joints which are not yet incorporated in codes thus providing a comprehensive aid for engineers concerned with the design or assessment of welded components or structures. Background information is given on the fatigue lives of welded joints which will enable the engineer or student to appreciate why there is such a contrast between welded and unwelded parts, why some welded joints perform better than others and how joints can be selected to optimise fatigue performance.
Download or read book Fatigue and Fracture of Weldments written by Uwe Zerbst and published by Springer. This book was released on 2018-12-11 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive and thorough guide to those readers who are lost in the often-confusing context of weld fatigue. It presents straightforward information on the fracture mechanics and material background of weld fatigue, starting with fatigue crack initiation and short cracks, before moving on to long cracks, crack closure, crack growth and threshold, residual stress, stress concentration, the stress intensity factor, J-integral, multiple cracks, weld geometries and defects, microstructural parameters including HAZ, and cyclic stress-strain behavior. The book treats all of these essential and mutually interacting parameters using a unique form of analysis.
Download or read book Fatigue of Welded Structures written by Timothy Russell Gurney and published by CUP Archive. This book was released on 1979-12-20 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Analysis of Welded Components written by E. Niemi and published by Woodhead Publishing. This book was released on 2006-09-27 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report provides background and guidance on the use of the structural hot spot stress approach to the fatigue design of welded components and structures. It complements the IIW recommendations for 'Fatigue Design of Welded Joints and Components' and extends the information provided in the IIW recommendations on 'Stress Determination for Fatigue Analysis of Welded Components'. This approach is applicable to cases of potential fatigue cracking from the weld toe. It has been in use for many years in the context of tubular joints. The present report concentrates on its extension to structures fabricated from plates and non-tubular sections.Following an explanation of the structural hot spot stress, its definition and its relevance to fatigue, the authors describe methods for its determination. Stress determination from both finite element analysis and strain gauge measurements is considered. Parametric formulae for calculating stress increases due to misalignment and structural discontinuities are also presented. Special attention is paid to the use of finite element stress analysis and guidance is given on the choice of element type and size for use with either solid or shell elements. Design S-N curves for use with the structural hot spot stress are presented for a range of weld details. Finally, practical application of the recommendations is illustrated in two case studies involving the fatigue assessment of welded structures using the structural hot spot stress approach. - Provides practical guidance on the application of the structural hot-spot stress approach - Discusses stress determination from both finite element analysis and strain gauge measurements - Practical application of the recommendations is illustrated in two case studies
Download or read book Stress Determination for Fatigue Analysis of Welded Components written by E. Niemi and published by Woodhead Publishing. This book was released on 1995-04-30 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report introduces definitions of the terminology relevant to stress determination for fatigue analysis of welded components. The various stress concentrations, stress categories and fatigue analysis methods are defined. Fatigue analysis methods considered are nominal stress, hot spot stress, notch stress, notch strain and fracture mechanics approaches. The report also contains comprehensive recommendations concerning the application of finite element methods and experimental methods for stress determination. It is intended for fatigue design of common welded structures, such as cranes, excavators, vehicle frames, bridges, ship hulls, offshore structures etc. fabricated from materials at least 3mm thick. In general, attention is focused on weld details which give rise to fatigue cracking from the surface, notably from the weld toe.
Download or read book Fatigue Life Prediction of Welded Joints Using Fracture Mechanics written by Kentaro Yamada and published by . This book was released on 1990 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design and Analysis of Fatigue Resistant Welded Structures written by Dieter Radaj and published by Woodhead Publishing. This book was released on 1990-01-03 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: An English version of a sucessful German book. Both traditional and modern concepts are described.
Download or read book Fatigue Assessment of Welded Joints by Local Approaches written by Dieter Radaj and published by Woodhead Publishing. This book was released on 2006-10-30 with total page 661 pages. Available in PDF, EPUB and Kindle. Book excerpt: Local approaches to fatigue assessment are used to predict the structural durability of welded joints, to optimise their design and to evaluate unforeseen joint failures. This standard work provides a systematic survey of the principles and practical applications of the various methods. It covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. Seam-welded and spot-welded joints in structural steels and aluminium alloys are also considered.This completely reworked second edition takes into account the tremendous progress in understanding and applying local approaches which has been achieved in the last decade. It is a standard reference for designers, structural analysts and testing engineers who are responsible for the fatigue-resistant in-service behaviour of welded structures. - Completely reworked second edition of a standard work providing a systematic survey of the principles and practical applications of the various methods - Covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. - Written by a distinguished team of authors
Download or read book Recommendations for Fatigue Design of Welded Joints and Components written by A. F. Hobbacher and published by Springer. This book was released on 2015-12-23 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a basis for the design and analysis of welded components that are subjected to fluctuating forces, to avoid failure by fatigue. It is also a valuable resource for those on boards or commissions who are establishing fatigue design codes. For maximum benefit, readers should already have a working knowledge of the basics of fatigue and fracture mechanics. The purpose of designing a structure taking into consideration the limit state for fatigue damage is to ensure that the performance is satisfactory during the design life and that the survival probability is acceptable. The latter is achieved by the use of appropriate partial safety factors. This document has been prepared as the result of an initiative by Commissions XIII and XV of the International Institute of Welding (IIW).
Download or read book Fatigue Design of Components written by G. Marquis and published by Elsevier. This book was released on 1997-12-10 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains a selection of papers presented at Fatigue Design 95 held in Helsinki, Finland from 5-8 September 1995. The papers have been peer reviewed and present practical aspects for the design of components and structures to avoid fatigue failure. Topics covered include: fatigue design experiences, ground vehicle components, component reliability, multiaxial fatigue, notch analysis, service loading, welded structures, probabilistics aspects in fatigue, fatigue design optimization.
Download or read book A Generalized Stress Parameter Approach for Fatigue Life Prediction of Seam Welded Joints written by and published by . This book was released on 2017 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis presents a new method, based on fracture mechanics analysis of fatigue, to calculate the generalized stress parameter proposed by Maddox.
Download or read book Fatigue Assessment of Welded Joints by Local Approaches written by Dieter Radaj and published by Woodhead Publishing. This book was released on 1998 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Design of Welded Joints and Components written by A Hobbacher and published by Woodhead Publishing. This book was released on 1996-10-31 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: These recommendations present general methods for the assessment of fatigue damage in welded components, which may affect the limit states of a structure, such as ultimate limit state and serviceability limited state. Fatigue resistance data is given for welded components made of wrought or extruded products of ferritic/pearlitic or banitic structural steels up to fy = 700 Mpa and of aluminium alloys commonly used for welded structures.
