Download or read book Fatigue Crack Closure at Near Threshold Growth Rates in Steels Effects of Microstructure Load Sequence and Environment written by Michael K. Schaper and published by . This book was released on 2012 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper summarizes long-term research on fatigue crack closure in several labs of the author. Various experimental techniques were used in different combinations. Primarily, a sophisticated dynamic compliance technique based on highly sensitive resonance vibration measurements and crack tip diffracted ultrasonic wave analysis is applied. Whereas the first method reflects the global through thickness behavior, the second method enables spatial resolution, which is achieved with a reduction of sensitivity yet has the advantage that the signal generation is independent on the stress state ahead of the crack tip. The results allow a coherent view into the effects of the stress state, material plasticity, fracture surface roughness, and oxidation tendency on the closure behavior and, therefore, on both the threshold stress intensity and near-threshold crack propagation. Specifically, the different load ratio, load sequence, and the environmental effects on the threshold values of ferritic, martensitic, and austenitic steels are addressed.
Download or read book Environmentally Affected Near Threshold Fatigue Crack Growth in Steels written by S. Suresh and published by . This book was released on 1983 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt: Environmentally affected fatigue crack propagation in steels is described for ultralow growth rates (below 10-6 mm/cycle) in terms of the role of crack surface corrosion debris in promoting crack closure. It is shown that the reported effects of gaseous and aqueous environments (air, water, hydrogen, helium, etc.) on near-threshold crack growth in lower strength steels are consistent primarily with an oxide-induced crack closure mechanism. Moist atmospheres, such as humid air and water, are shown to promote the formation of oxide deposits within the crack, which at low load ratios are thickened by fretting-assisted oxidation to maximum thicknesses comparable with cracktip opening displacements. Using ultrasonic techniques, this is shown to increase closure loads and to lower effective alternating stress intensities at the crack tip. Observations that near-threshold growth in dry helium is similar to that in dry hydrogen gas and faster than in air, are shown to be consistent with such concepts since both environments provide a dry atmosphere limiting oxide formation. Extensive data on near-threshold corrosion-fatigue crack growth in ultrahigh-strength (300-M) and lower-strength (21⁄4Cr-1Mo and SA516) steels are examined in the context of this mechanism, and it is found that the threshold for no crack growth (?Ko) is consistent with a maximum excess oxide thickness approximately equal to the pulsating crack-tip displacement (?CTOD). The implications of this and other microscopic mechanisms of closure are discussed in the light of microstructural and environmental influences on near-threshold fatigue.
Download or read book Comparison of Environmentally influenced Near threshold Fatigue crack growth Behavior in High and Lower strength Steels at Conventional Frequencies written by and published by . This book was released on 1982 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent studies in a wide variety of steels, of yield strengths ranging from 290 to 1740 MPa, have indicated that environmental influences on corrosion fatigue crack propagation at near-threshold levels (growth rates below approx. 10/sup -6/ mm/cycle), may be markedly different from those at higher growth rates. In this paper, the effect of such environments, specifically dry gaseous hydrogen and moist room air, on near-threshold cyclic crack growth is reviewed and comparisons made between behavior in high and lower strength steels. It is shown that, in lower strength steels (yield strength less than or equal to 700 MPa), near-threshold growth rates in dry hydrogen exceed those in moist air by up to two orders of magnitude at low load ratios only, whereas for steels of strength levels above approx. 700 MPa, the presence of hydrogen results in lower near-threshold growth rates compared to moist air regardless of load ratio. Such behavior is rationalized in terms of the competing effects of hydrogen embrittlement and oxide-induced crack closure mechanisms.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 836 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture Mechanics fourteenth Symposium Volume 1 Theory and Analysis written by and published by ASTM International. This book was released on with total page 615 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Fatigue Crack Propagation in Metallic Structures written by A. Carpinteri and published by Newnes. This book was released on 2012-12-02 with total page 834 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this Handbook is to provide a review of the knowledge and experiences in the field of fatigue fracture mechanics. It is well-known that engineering structures can fail due to cyclic loading. For instance, a cyclically time-varying loading reduces the structure strength and can provoke a fatigue failure consisting of three stages: (a) crack initiation (b) crack propagation and (c) catastrophic failure. Since last century many scientists have tried to understand the reasons for the above-mentioned failures and how to prevent them. This Handbook contains valuable contributions from leading experts within the international scientific community and covers many of the important problems associated with the fatigue phenomena in civil, mechanical and nuclear engineering.
Download or read book Advances in Fatigue Crack Closure Measurement and Analysis written by R. Craig McClung and published by ASTM International. This book was released on 1999 with total page 487 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Comprehensive Structural Integrity written by Ian Milne and published by Elsevier. This book was released on 2003-07-25 with total page 4647 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of this major reference work is to provide a first point of entry to the literature for the researchers in any field relating to structural integrity in the form of a definitive research/reference tool which links the various sub-disciplines that comprise the whole of structural integrity. Special emphasis will be given to the interaction between mechanics and materials and structural integrity applications. Because of the interdisciplinary and applied nature of the work, it will be of interest to mechanical engineers and materials scientists from both academic and industrial backgrounds including bioengineering, interface engineering and nanotechnology. The scope of this work encompasses, but is not restricted to: fracture mechanics, fatigue, creep, materials, dynamics, environmental degradation, numerical methods, failure mechanisms and damage mechanics, interfacial fracture and nano-technology, structural analysis, surface behaviour and heart valves. The structures under consideration include: pressure vessels and piping, off-shore structures, gas installations and pipelines, chemical plants, aircraft, railways, bridges, plates and shells, electronic circuits, interfaces, nanotechnology, artificial organs, biomaterial prostheses, cast structures, mining... and more. Case studies will form an integral part of the work.
Download or read book Gaseous Hydrogen Embrittlement of Materials in Energy Technologies written by Richard P Gangloff and published by Elsevier. This book was released on 2012-01-16 with total page 864 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many modern energy systems are reliant on the production, transportation, storage, and use of gaseous hydrogen. The safety, durability, performance and economic operation of these systems is challenged by operating-cycle dependent degradation by hydrogen of otherwise high performance materials. This important two-volume work provides a comprehensive and authoritative overview of the latest research into managing hydrogen embrittlement in energy technologies.Volume 1 is divided into three parts, the first of which provides an overview of the hydrogen embrittlement problem in specific technologies including petrochemical refining, automotive hydrogen tanks, nuclear waste disposal and power systems, and H2 storage and distribution facilities. Part two then examines modern methods of characterization and analysis of hydrogen damage and part three focuses on the hydrogen degradation of various alloy classesWith its distinguished editors and international team of expert contributors, Volume 1 of Gaseous hydrogen embrittlement of materials in energy technologies is an invaluable reference tool for engineers, designers, materials scientists, and solid mechanicians working with safety-critical components fabricated from high performance materials required to operate in severe environments based on hydrogen. Impacted technologies include aerospace, petrochemical refining, gas transmission, power generation and transportation. - Summarises the wealth of recent research on understanding and dealing with the safety, durability, performance and economic operation of using gaseous hydrogen at high pressure - Reviews how hydrogen embrittlement affects particular sectors such as the petrochemicals, automotive and nuclear industries - Discusses how hydrogen embrittlement can be characterised and its effects on particular alloy classes
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1982 with total page 916 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Crack Growth Thresholds Endurance Limits and Design written by J. C. Newman and published by ASTM International. This book was released on 2000 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Contains 24 papers from the November, 1998 symposium of the same name, sponsored by the ASTM Committee E8 on Fatigue and Fracture, and presented by Newman and Piascik (both of the NASA Langley Research Center). The papers focus on such areas as fatigue-crack growth threshold mechanisms, loading and specimen-type effects, analyses of fatigue-crack-growth-threshold behavior, and applications of threshold concepts and endurance limits to aerospace and structural materials. Annotation copyrighted by Book News, Inc., Portland, OR.
Download or read book Introduction to Fatigue in Metals and Composites written by R.L. Carlson and published by Springer Science & Business Media. This book was released on 1995-11-30 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to Fatigue in Metals and Composites provides a balanced treatment of the phenomenon of fatigue in metals, nonmetals and composites with polymeric, metallic and ceramic matrices. The applicability of the safe life philosophy of design is examined for each of the materials. Attention is also focused on the stable crack growth phase of fatigue and differences in the operative mechanisms for the various classes of materials are considered. The impacts of these differences on the development of damage tolerance strategies are examined. Among topics discussed are; variable amplitude loading with tensile and compressive overload; closure obstruction; bridging mechanisms; mixed mode states; small cracks; delamination mechanisms and environmental conditions. The arrangement and presentation of the topics are such that An Introduction to Fatigue in Metals and Composites can serve as a course text for mechanical, civil, aeronautical and astronautical engineering and material science courses as well as a reference for engineers who are concerned with fatigue testing and aircraft, automobile and engine design.
Download or read book Metals Abstracts written by and published by . This book was released on 1992 with total page 1796 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Crack Growth Under Spectrum Loads written by Ralph Ivan Stephens and published by ASTM International. This book was released on 1976 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue of Materials written by Subra Suresh and published by Cambridge University Press. This book was released on 1998-10-29 with total page 708 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by a leading researcher in the field, this revised and updated second edition of a highly successful book provides an authoritative, comprehensive and unified treatment of the mechanics and micromechanisms of fatigue in metals, non-metals and composites. The author discusses the principles of cyclic deformation, crack initiation and crack growth by fatigue, covering both microscopic and continuum aspects. The book begins with discussions of cyclic deformation and fatigue crack initiation in monocrystalline and polycrystalline ductile alloys as well as in brittle and semi-/non-crystalline solids. Total life and damage-tolerant approaches are then introduced in metals, non-metals and composites followed by more advanced topics. The book includes an extensive bibliography and a problem set for each chapter, together with worked-out example problems and case studies. This will be an important reference for anyone studying fracture and fatigue in materials science and engineering, mechanical, civil, nuclear and aerospace engineering, and biomechanics.
Download or read book Fracture Mechanics written by J. C. Lewis and published by ASTM International. This book was released on 1983 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Strength and Grain Size on Near threshold Fatigue Crack Growth in Ultra high Strength Steel written by and published by . This book was released on 1976 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue tests were performed on ultra-high strength steels to assess (i) the influence of strength at constant grain size, and (ii) the influence of grain size at constant strength, on threshold stress intensity and near-threshold crack propagation rates. The results constitute part of a larger program of research to characterize the microstructural influences on fatigue crack propagation at growth rates less than 10−5 mm/cycle in an attempt to provide a basis for the design of alloys resistant to low growth rate fatigue failure.
