Download or read book Fatigue and Fracture Mechanics of High Risk Parts written by Bahram Farahmand and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the preliminary stage of designing new structural hardware that must perform a given mission in a fluctuating load environment, there are several factors the designers should consider. Trade studies for different design configurations should be performed and, based on strength and weight considerations, among others, an optimum configuration selected. The selected design must be able to withstand the environment in question without failure. Therefore, a comprehen sive structural analysis that consists of static, dynamic, fatigue, and fracture is necessary to ensure the integrity of the structure. During the past few decades, fracture mechanics has become a necessary discipline for the solution of many structural problems. These problems include the prevention of failures resulting from preexisting cracks in the parent material, welds or that develop under cyclic loading environment during the life of the structure. The importance of fatigue and fracture in nuclear, pressure vessel, aircraft, and aerospace structural hardware cannot be overemphasized where safety is of utmost concern. This book is written for the designer and strength analyst, as well as for the material and process engineer who is concerned with the integrity of the structural hardware under load-varying environments in which fatigue and frac ture must be given special attention. The book is a result of years of both acade mic and industrial experiences that the principal author and co-authors have accumulated through their work with aircraft and aerospace structures.
Download or read book Fatigue and Fracture 1997 written by and published by . This book was released on 1997 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Damage Crack Growth and Life Prediction written by F. Ellyin and published by Springer Science & Business Media. This book was released on 1996-11-30 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue failure is a multi-stage process. It begins with the initiation of cracks, and with continued cyclic loading the cracks propagate, finally leading to the rupture of a component or specimen. The demarcation between the above stages is not well-defined. Depending upon the scale of interest, the variation may span three orders of magnitude. For example, to a material scientist an initiated crack may be of the order of a micron, whereas for an engineer it can be of the order of a millimetre. It is not surprising therefore to see that investigation of the fatigue process has followed different paths depending upon the scale of phenomenon under investigation. Interest in the study of fatigue failure increased with the advent of industrial ization. Because of the urgent need to design against fatigue failure, early investiga tors focused on prototype testing and proposed failure criteria similar to design formulae. Thus, a methodology developed whereby the fatigue theories were proposed based on experimental observations, albeit at times with limited scope. This type of phenomenological approach progressed rapidly during the past four decades as closed-loop testing machines became available.
Download or read book Multiaxial Fatigue and Fracture written by E. Macha and published by Elsevier. This book was released on 1999-09-06 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains 18 papers selected from 90 presented at the Fifth International Conference on Biaxial/Multiaxial Fatigue and Fracture held in Cracow, Poland 8-12 September 1997. The papers in this book deal with theoretical, computational and experimental aspects of the multiaxial fatigue and fracture of engineering materials and structures. The papers are divided into the following four categories: 1. Proportional cyclic loading 2. Non-proportional cyclic loading 3. Variable amplitude and random loading 4. Crack growth Most papers in this publication talk about the behaviour of constructional materials and elements of machines under non-proportional loading and under variable amplitude and random loading, which are more realistic load histories met in industrial practice. Variable amplitude loading under cyclic load with basic frequency and random loading under load with a continuous band of frequency is classified here. This book gives a review of the latest world success and directions of investigations on multiaxial fatigue and fracture. More and more often publications are results of the co-operation of researchers from different laboratories and countries. Seven out of eighteen papers included here were worked out by international authors teams. This is a symptom of the times, when science and investigations know no borders.
Download or read book Fatigue and Fracture Mechanics written by John H. Underwood and published by ASTM International. This book was released on 1997 with total page 697 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue and Fracture Mechanics written by Kenneth L. Jerina and published by ASTM International. This book was released on 2000 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Notch Effects in Fatigue and Fracture written by G. Pluvinage and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: As Directors of this NATO Workshop, we welcome this opportunity to record formally our thanks to the NATO Scientific Affairs Division for making our meeting possible through generous financial support and encouragement. This meeting has two purposes: the first obvious one because we have collected scientists from East, far East and west to discuss new development in the field of fracture mechanics: the notch fracture mechanics. The second is less obvious but perhaps in longer term more important that is the building of bridges between scientists in the frame of a network called Without Walls Institute on Notch Effects in Fatigue and Fracture". Physical perception of notch effects is not so easy to understand as the presence of a geometrical discontinuity as a worst effect than the simple reduction of cross section. Notch effects in fatigue and fracture is characterised by the following fundamental fact: it is not the maximum local stress or stress which governs the phenomena of fatigue and fracture. The physic shows that a process volume is needed probably to store the necessary energy for starting and propagating the phenomenon. This is a rupture of the traditional "strength of material" school which always give the prior importance of the local maximum stress. This concept of process volume was strongly affirmed during this workshop.
Download or read book Fatigue and Fracture Mechanics written by and published by . This book was released on 1911 with total page 920 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Time Dependent Fracture Mechanics written by Dominique P. Miannay and published by Springer Science & Business Media. This book was released on 2001 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intended for engineers, researchers, and graduate students dealing with materials science, structural design, and nondestructive testing and evaluation, this book represents a continuation of the author's 'Fracture Mechanics' (1997). It will appeal to a variety of audiences: The discussion of design codes and procedures will be of use to practicing engineers, particularly in the nuclear, aerospace, and pipeline industries; the extensive bibliography and discussion of recent results will make it a useful reference for academic researchers; and graduate students will find the clear explanations and worked examples useful for learning the field. The book begins with a general treatment of fracture mechanics in terms of material properties and loading and provides up-to-date reviews of the ductile-brittle transition in steels and of methods for analyzing the risk of fracture. It then discusses the dynamics of fracture and creep in homogeneous and isotropic media, including discussions of high-loading-rate characteristics, the behavior of stationary cracks in elastic media under stress, and the propagation of cracks in elastic media. This is followed by an analysis of creep and crack initiation and propagation, describing, for example, the morphology and incubation times of crack initiation and growth and the effects of high temperatures. The book concludes with treatments of cycling deformation and fatigue, creep-fatigue fractures, and crack initiation and propagation. Problems at the end of each chapter serve to reinforce and test the student's knowledge and to extend some of the discussions in the text. Solutions to half of the problems are provided.
Download or read book Fatigue and Fracture written by Sharif Rahman and published by . This book was released on 1997 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: Volume two contains 39 papers presented at the July 1997 conference. Contributions are organized in six sections: user's experience with failure assessment diagrams; vessel fracture; constraint; probabilistic fracture mechanics; fracture assessment; and fracture of welds. Topics include applications
Download or read book Fatigue and Fracture in Steel Bridges written by John W. Fisher and published by Wiley-Interscience. This book was released on 1984 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a detailed review and summary of twenty-two case studies of fracture and fatigue in bridge structures. Its two parts cover cracks formed as a result of low fatigue resistant details, and cracks resulting from unanticipated secondary or displacement induced stresses.
Download or read book ASM HANDBOOK VOLUME 4F written by ASM INTERNATIONAL. and published by . This book was released on 2024 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue and Fracture written by F. C. Campbell and published by ASM International. This book was released on 2012-01-01 with total page 699 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This book emphasizes the physical and practical aspects of fatigue and fracture. It covers mechanical properties of materials, differences between ductile and brittle fractures, fracture mechanics, the basics of fatigue, structural joints, high temperature failures, wear, environmentally-induced failures, and steps in the failure analysis process."--publishers website.
Download or read book Introduction to Fatigue and Fracture Mechanics written by L. Gansted and published by . This book was released on 1992 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Selected Papers on Foundations of Linear Elastic Fracture Mechanics written by Robert Joseph Sanford and published by . This book was released on 1997 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: SPIE Milestones are collections of seminal papers from the world literature covering important discoveries and developments in optics and photonics.
Download or read book Fatigue and Fracture Mechanics written by Sreeramesh Kalluri and published by . This book was released on 2011 with total page 701 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue and Fracture Mechanics written by Ravinder Chona and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
