Download or read book Experimental Method for Correcting Nozzle Afterbody Drag for the Effects of Jet Temperature written by W. L. Peters and published by . This book was released on 1981 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this investigation was to isolate those parameters defined as jet mixing effects on afterbody drag in an effort to develop a method of correcting or simulating the effects of jet temperature in wind tunnel experiments. Data used in the investigation were obtained from experiments conducted in the AEDC Aerodynamic Wind Tunnel (1T) with a strut-mounted model at free-stream Mach numbers from 0.6 to 1.2. Integrated afterbody pressure drag coefficient data were acquired for three nozzle area ratios (1.0, 1.24, and 2.96) using various unheated jet exhaust gas compositions that allowed a variation in gas constant from 55 to 767 ft/lbf/lbm-deg R. Jet mixing effects on afterbody drag coefficient produced by varying jet gas constant and nozzle area ratio at nozzle design pressure ratio, and the drag effects resulting from variations in nozzle pressure ratio at certain overexpanded jet conditions were observed to be similar functions of mass flux ratio. A simple experimental method has been proposed to allow corrections of afterbody drag coefficient data obtained in the wind tunnel (using an ambient temperature air jet) for the effects of jet gas constant. By inference, a similar drag correction can be obtained for the combined effect of gas constant and temperature, assuming their product defines the effects on drag produced by variations in either property. (Author).
Download or read book Experimental Method for Correcting Nozzle Afterbody Drag for the Effects of Jet Temperature written by W. L. Peters and published by . This book was released on 1981 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this investigation was to isolate those parameters defined as jet mixing effects on afterbody drag in an effort to develop a method of correcting or simulating the effects of jet temperature in wind tunnel experiments. Data used in the investigation were obtained from experiments conducted in the AEDC Aerodynamic Wind Tunnel (1T) with a strut-mounted model at free-stream Mach numbers from 0.6 to 1.2. Integrated afterbody pressure drag coefficient data were acquired for three nozzle area ratios (1.0, 1.24, and 2.96) using various unheated jet exhaust gas compositions that allowed a variation in gas constant from 55 to 767 ft/lbf/lbm-deg R. Jet mixing effects on afterbody drag coefficient produced by varying jet gas constant and nozzle area ratio at nozzle design pressure ratio, and the drag effects resulting from variations in nozzle pressure ratio at certain overexpanded jet conditions were observed to be similar functions of mass flux ratio. A simple experimental method has been proposed to allow corrections of afterbody drag coefficient data obtained in the wind tunnel (using an ambient temperature air jet) for the effects of jet gas constant. By inference, a similar drag correction can be obtained for the combined effect of gas constant and temperature, assuming their product defines the effects on drag produced by variations in either property. (Author).
Download or read book Experimental Method for Correcting Nozzle Afterbody Drag for the Effects of Jet Temperature written by and published by . This book was released on 1981 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this investigation was to isolate those parameters defined as jet mixing effects on afterbody drag in an effort to develop a method of correcting or simulating the effects of jet temperature in wind tunnel experiments. Data used in the investigation were obtained from experiments conducted in the AEDC Aerodynamic Wind Tunnel (1T) with a strut-mounted model at free-stream Mach numbers from 0.6 to 1.2. Integrated afterbody pressure drag coefficient data were acquired for three nozzle area ratios (1.0, 1.24, and 2.96) using various unheated jet exhaust gas compositions that allowed a variation in gas constant from 55 to 767 ft/lbf/lbm-deg R. Jet mixing effects on afterbody drag coefficient produced by varying jet gas constant and nozzle area ratio at nozzle design pressure ratio, and the drag effects resulting from variations in nozzle pressure ratio at certain overexpanded jet conditions were observed to be similar functions of mass flux ratio. A simple experimental method has been proposed to allow corrections of afterbody drag coefficient data obtained in the wind tunnel (using an ambient temperature air jet) for the effects of jet gas constant. By inference, a similar drag correction can be obtained for the combined effect of gas constant and temperature, assuming their product defines the effects on drag produced by variations in either property. (Author).
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1992 with total page 1572 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Exhaust Plume Temperature Effects on Nozzle Afterbody Performance Over the Transonic Mach Number Range written by C. E. Robinson and published by . This book was released on 1974 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results of an experimental and analytical research investigation on nozzle/afterbody drag are presented. Experimental afterbody (and boattail) drag coefficients and pressure distributions are discussed for an isolated, strut-mounted nozzle/afterbody model for the Mach number range from 0.6 to 1.5. Some data are also given for free-stream unit Reynolds numbers from one million to approximately four million per foot. The experimental data were obtained for the basic model with an air-cooled and a water-cooled Ethylene/air combustor to provide hot-jet duplication as well as cold-jet simulation. The temperature of the nozzle exhaust gas was varied from 530R (burner-off) to approximately 2500R for several nozzle pressure ratios from jet-off to those corresponding to a moderately under-expanded exhaust plum. The initial series of experiments was conducted with the air-cooled combustors, and the effect of jet temperature on afterbody drag was somewhat masked by the effects of the secondary airflow from the cooling air. The general trend, however, shows a decreasing afterbody drag with increasing exhaust gas temperature and with decreasing secondary airflow at a fixed nozzle pressure ratio. (Modified author abstract).
Download or read book Technical Abstract Bulletin written by and published by . This book was released on 1981 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Method for Estimating Jet Entrainment Effects on Nozzle Afterbody Drag written by and published by . This book was released on 1980 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: A highly simplified analysis was used to derive an expression for estimating the induced afterbody drag caused by the turbulent jet-mixing process. The approach estimates the induced velocity produced by the jet-mixing process and uses small perturbation concepts to estimate the resulting pressure change on the afterbody surface from which the induced afterbody drag coefficient is obtained. The theoretical induced afterbody drag (entrainment drag) is combined with the maximum jet plume diameter blockage condition to form a correlation method that accounts for the effect of jet area ratio, exit angle, total temperature, molecular weight and ratio of specific heats for a given external stream Mach number, Reynolds number, and afterbody geometry. For verification, the correlation method was used to predict the drag of an H2 and C2H4 jet from the measured drag of an N2 jet and to predict the drag of a hot jet from the measured drag of a cold jet for both the 15- and 25-deg AGARD afterbody configurations in the Mach number range from 0.6 to 1.5. The average accuracy of the correlation method is better than 10% for both afterbody configurations and is 40 to 50 % more accurate than a correlation method based only on the blockage parameter. A brief numerical study indicates that the major parameter which correlates the jet entrainment effect is the product of the jet gas constant and total temperature. (Author).
Download or read book Wind Tunnels and Testing Techniques written by North Atlantic Treaty Organization. Advisory Group for Aerospace Research and Development and published by . This book was released on 1984 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Evaluation of Jet Simulation Parameters for Nozzle Afterbody Testing at Transonic Mach Numbers written by William Lee Peters and published by . This book was released on 1976 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this investigation was to evaluate various jet simulation parameters in an attempt to establish a method of matching hot jet interference with cold jet flows. Successful parameters were determined based on their ability to correlate integrated afterbody pressure drag, a measurement of aerodynamic interference, for jet flows of varying total temperature. Data used in this investigation were obtained from experiments conducted in the AEDC Propulsion Wind Tunnel (16T) with three different isolated nozzle/afterbody configurations at free-stream Mach numbers from 0.6 to 1.5. Gas temperature effects on pressure drag were acquired with a convergent nozzle utilizing an air/ethylene burner to produce gas temperatures from 540 to 3,300 R. In addition, the jet effects of varying internal nozzle geometry, specifically nozzle divergence half-angle and nozzle exit-to-throat area ratio, were investigated utilizing high-pressure air as the nozzle exhaust gas. Jet simulation parameters were evaluated for jet flows where nozzle exit-to-throat area ratio was varied from 1.0 to approximately 1.5 and where divergence half-angle was varied from 0 to 10 deg.
Download or read book An Evaluation of Nozzle Afterbody Code written by Frederick C. Guyton and published by . This book was released on 1986 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evaluation of Boattail Geometry and Exhaust Plume Temperature Effects on Nozzle Afterbody Drag at Transonic Mach Numbers written by L. L. Galigher and published by . This book was released on 1976 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental program was conducted to investigate the interaction effects which occur between the nozzle exhaust flow and the external flow field associated with isolated nozzle afterbody configurations at transonic Mach numbers. Pressure data were obtained from three afterbody geometries with boattail angles of 10, 15, and 25 deg at Mach numbers from 0.6 to 1.5 at zero angles of attack and sideslip. Cold (High-pressure air) and hot (Air/ethylene combustion) jet test techniques were used to simulate and duplicate, respectively, the nozzle exhaust flow for a sonic jet installation. Nozzle exhaust temperature was varied from 540 to approximately 2,900 R. The most significant results pertain to those effects on boattail pressure drag caused by exhaust plume temperature and flow asymmetry (Model support strut induced). The differences obtained in boattail pressure drag between the cold jet simulation and hot jet duplication results were significant at nozzle pressure ratios representative for turbofan and turbojet engines at subsonic Mach numbers. Adjusting the cold jet nozzle pressure ratio to correct for changes in the exhaust plume specific heat ratio with temperature did not account for the differences observed. Flow asymmetry effects were Mach number and nozzle pressure ratio dependent and increased in severity as the boattail angle was increased.
Download or read book Government Reports Annual Index written by and published by . This book was released on 1981 with total page 932 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sections 1-2. Keyword Index.--Section 3. Personal author index.--Section 4. Corporate author index.-- Section 5. Contract/grant number index, NTIS order/report number index 1-E.--Section 6. NTIS order/report number index F-Z.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1 957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 28 (thesis year 1 983) a total of 10,661 theses titles from 26 Canadian and 197 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 28 reports theses submitted in-1983, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.
Download or read book Computation of Axisymmetric Separated Nozzle afterbody Flow written by James L. Jacocks and published by . This book was released on 1980 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of a computer program for solving the compressible, axisymmetric, mass-averaged Navier-Stokes equations is described. The basic numerical algorithm is the MacCormack explicit predictor-corrector scheme. Turbulence modeling is accomplished using an algebraic, two-layer eddy viscosity model with a novel modification dependent on the streamwise gradient of vorticity. Comparisons of computed results with experimental data are presented for several nozzle-afterbody configurations with either or simulated plumes. (Author).
Download or read book NASA SP written by and published by . This book was released on 1986 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Aeronautical Engineering written by and published by . This book was released on 1985 with total page 942 pages. Available in PDF, EPUB and Kindle. Book excerpt: A selection of annotated references to unclassified reports and journal articles that were introduced into the NASA scientific and technical information system and announced in Scientific and technical aerospace reports (STAR) and International aerospace abstracts (IAA).
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 974 pages. Available in PDF, EPUB and Kindle. Book excerpt:
