Download or read book Experimental Investigations of Nanosceond Pulsed Laser Micromachining of Metal Using Thin Film Microsensors written by Hong Seok Choi and published by . This book was released on 2007 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Femtosecond Pulsed Laser Deposition and Patterning of Thin Films for MEMS written by Michael Joseph Stock and published by . This book was released on 2003 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: Procedural variables such as fluence, polarization, pulse width, machining speed, and material properties are investigated to determine their effects on the PLD and laser micromachining of aluminum magnesium boride. In this work, a 120-fs pulsed, 800-nm wavelength Ti: Sapphire laser was used for micromachining thin films of ultra-hard AlMgB14 and polysilicon thin films on silicon substrate. Polysilicon was first deposited by low-pressure chemical vapor deposition followed by boride using femtosecond pulsed laser deposition. Channels were then machined in thin films to pattern a device that would produce a linear resistance/deflection curve. Results show that the ultrafast laser has precisely ablated the thin films. However, the high-energy fluence used in single-pass surface micromachining enabled the formation of recast layer of molten silicon substrate ejected by vapor pressure, and conglomerates of re-condensed material at a distance from the feature. Multi-pass surface micromachining at low energy fluences eliminated the recast layers and produced clean features. Ultrafast laser micromachining is certainly beneficial over wet and dry etching in reproducibility, material choice, and minimal number of processing steps. Thin films of ultra-hard AlMgB14 were grown on Si (100) substrates at 300 K using femtosecond pulsed Ti:sapphire laser and subsequently annealed in argon gas up to 1373 K for two hours. X-ray photoelectron spectroscopy, X-ray diffraction, atomic force microscope, and nanoindentation were employed to study the composition, microstructure and hardness of thin films. Results were compared with nanosecond pulsed KrF excimer laser-deposited films. The as-deposited and post-annealed films (up to 1173 K), independent of the pulse width, exhibited amorphous structures with a hardness of 40 GPa. However, post-annealing at higher temperatures has varied effects on crystallization depending on the pulse width. The effect of pulse width on the microstructure and quality of thin films is discussed.
Download or read book Nanoscale Metal Thin Film Dewetting Via Nanosecond Laser Melting written by Yueying Wu and published by . This book was released on 2011 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanoscale metal thin film dewetting via laser treatment is studied in this dissertation. The purpose is to understand: 1) the spatial and temporal nature of intrinsic instabilities; and 2) mass transportation involved in dewetting pattern evolution in metal thin films as well as in lithographically patterned nanostructures; and finally 3) to explore advanced control of metallic nanostructure fabrication via the confluence of top down nanolithography and pulsed laser induced dewetting. This study includes three sections. In first section, thin film Cu-Ni alloys ranging from 2-8nm were synthesized and laser irradiated. The evolution of the spinodal dewetting process is investigated as a function of the thin film composition which ultimately dictates the size distribution and spacing of the nanoparticles, and the optical measurements of the copper rich alloy nanoparticles revealed characteristic plasmonic peaks. In section two, the dewetting behavior of nanolithographically patterned copper rings on Silicon substrate was studied. The self assembly of the rings into ordered nanoparticle/nanodrop arrays was accomplished via nanosecond pulsed laser heating. The resultant length scale of the 13nm and 7nm thick copper rings was correlated to the competition between transport and instabilities time scales during the liquid lifetime of the melted copper rings. To explore the influence of different substrates with different surface energy, the pulsed laser heated assembly of lithographically patterned copper rings on SiO2 substrate was studied in the last section. The correlated transport and instabilities show modified timescales. It is demonstrated again that the original geometry dictates the instability pathway, which for narrow rings obeys the Rayleigh-Plateau instability and for wider rings are influenced by the thin film instability.
Download or read book Advances in Micro and Nano Manufacturing and Surface Engineering written by M. S. Shunmugam and published by Springer Nature. This book was released on 2019-11-30 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents research papers on micro and nano manufacturing and surface engineering which were presented during the 7th International and 28th All India Manufacturing Technology, Design and Research conference 2018 (AIMTDR 2018). The papers discuss the latest advances in miniature manufacturing, the machining of miniature components and features as well as improvement of surface properties. This volume will be of interest to academicians, researchers, and practicing engineers alike.
Download or read book Laser Precision Microfabrication written by Koji Sugioka and published by Springer. This book was released on 2010-08-13 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: Miniaturization and high precision are rapidly becoming a requirement for many industrial processes and products. As a result, there is greater interest in the use of laser microfabrication technology to achieve these goals. This book composed of 16 chapters covers all the topics of laser precision processing from fundamental aspects to industrial applications to both inorganic and biological materials. It reviews the sate of the art of research and technological development in the area of laser processing.
Download or read book Handbook of Modern Sensors written by Jacob Fraden and published by Springer Science & Business Media. This book was released on 2006-04-29 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: Seven years have passed since the publication of the previous edition of this book. During that time, sensor technologies have made a remarkable leap forward. The sensitivity of the sensors became higher, the dimensions became smaller, the sel- tivity became better, and the prices became lower. What have not changed are the fundamental principles of the sensor design. They are still governed by the laws of Nature. Arguably one of the greatest geniuses who ever lived, Leonardo Da Vinci, had his own peculiar way of praying. He was saying, “Oh Lord, thanks for Thou do not violate your own laws. ” It is comforting indeed that the laws of Nature do not change as time goes by; it is just our appreciation of them that is being re?ned. Thus, this new edition examines the same good old laws of Nature that are employed in the designs of various sensors. This has not changed much since the previous edition. Yet, the sections that describe the practical designs are revised substantially. Recent ideas and developments have been added, and less important and nonessential designs were dropped. Probably the most dramatic recent progress in the sensor technologies relates to wide use of MEMS and MEOMS (micro-electro-mechanical systems and micro-electro-opto-mechanical systems). These are examined in this new edition with greater detail. This book is about devices commonly called sensors. The invention of a - croprocessor has brought highly sophisticated instruments into our everyday lives.
Download or read book Laser Fabrication and Machining of Materials written by Narendra B. Dahotre and published by Springer Science & Business Media. This book was released on 2008-01-25 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the fundamental principles and physical phenomena behind laser-based fabrication and machining processes. It also gives an overview of their existing and potential applications. With laser machining an emerging area in various applications ranging from bulk machining in metal forming to micromachining and microstructuring, this book provides a link between advanced materials and advanced manufacturing techniques. The interdisciplinary approach of this text will help prepare students and researchers for the next generation of manufacturing.
Download or read book Micro Manufacturing Technologies and Their Applications written by Irene Fassi and published by Springer. This book was released on 2017-01-31 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides in-depth theoretical and practical information on recent advances in micro-manufacturing technologies and processes, covering such topics as micro-injection moulding, micro-cutting, micro-EDM, micro-assembly, micro-additive manufacturing, moulded interconnected devices, and microscale metrology. It is designed to provide complementary material for the related e-learning platform on micro-manufacturing developed within the framework of the Leonardo da Vinci project 2013-3748/542424: MIMAN-T: Micro-Manufacturing Training System for SMEs. The book is mainly addressed to technicians and prospective professionals in the sector and will serve as an easily usable tool to facilitate the translation of micro-manufacturing technologies into tangible industrial benefits. Numerous examples are included to assist readers in learning and implementing the described technologies. In addition, an individual chapter is devoted to technological foresight, addressing market analysis and business models for micro-manufacturers.
Download or read book Textbook of Nanoscience and Nanotechnology written by B.S. Murty and published by Springer Science & Business Media. This book was released on 2013-12-06 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is meant to serve as a textbook for beginners in the field of nanoscience and nanotechnology. It can also be used as additional reading in this multifaceted area. It covers the entire spectrum of nanoscience and technology: introduction, terminology, historical perspectives of this domain of science, unique and widely differing properties, advances in the various synthesis, consolidation and characterization techniques, applications of nanoscience and technology and emerging materials and technologies.
Download or read book Nanotribology written by Stephen M. Hsu and published by Springer. This book was released on 2012-10-08 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanotribology: Critical Assessment and Research Needs is an excellent reference for both academic and industrial researchers working in the fields of nanotechnology, tribology, mechanical engineering, materials science and engineering, MEMS, NEMS, magnetic recording, and biomedical devices. It will also be of interest to those pursuing scanning probe microscopy, nanoimaging, mesomanufacturing, sensors, actuators, aerospace, defense (controllers, microsystems), and military systems. Nanotribology: Critical Assessment and Research Needs provides a critical assessment of the current state of the art of nanotribology within the context of MEMS, mesomanufacturing, nanotechnology and microsystems. It contains chapters written by the leading experts in these fields. It identifies gaps in current knowledge and barriers to applications, and recommends research areas that need to be addressed to enable the rapid development of technologies.
Download or read book Semiconductor Gas Sensors written by Raivo Jaaniso and published by Woodhead Publishing. This book was released on 2019-09-24 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor Gas Sensors, Second Edition, summarizes recent research on basic principles, new materials and emerging technologies in this essential field. Chapters cover the foundation of the underlying principles and sensing mechanisms of gas sensors, include expanded content on gas sensing characteristics, such as response, sensitivity and cross-sensitivity, present an overview of the nanomaterials utilized for gas sensing, and review the latest applications for semiconductor gas sensors, including environmental monitoring, indoor monitoring, medical applications, CMOS integration and chemical warfare agents. This second edition has been completely updated, thus ensuring it reflects current literature and the latest materials systems and applications. Includes an overview of key applications, with new chapters on indoor monitoring and medical applications Reviews developments in gas sensors and sensing methods, including an expanded section on gas sensor theory Discusses the use of nanomaterials in gas sensing, with new chapters on single-layer graphene sensors, graphene oxide sensors, printed sensors, and much more
Download or read book Optical Thermal Response of Laser Irradiated Tissue written by Ashley J. Welch and published by Springer Science & Business Media. This book was released on 2011-01-15 with total page 951 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition maintains the standard of excellence established in the first edition, while adjusting the content to reflect changes in tissue optics and medical applications since 1995. The material concerning light propagation now contains new chapters devoted to electromagnetic theory for coherent light. The material concerning thermal laser-tissue interactions contains a new chapter on pulse ablation of tissue. The medical applications section now includes several new chapters on Optical Coherent Tomography, acoustic imaging, molecular imaging, forensic optics and nerve stimulation. A detailed overview is provided of the optical and thermal response of tissue to laser irradiation along with diagnostic and therapeutic examples including fiber optics. Sufficient theory is included in the book so that it is suitable for a one or two semester graduate or for senior elective courses. Material covered includes (1) light propagation and diagnostic application; (2) the thermal response of tissue and therapeutic application; (3) denaturation; and (4) ablation. The theory and applications provide researchers with sufficient detail that this volume will become the primary reference for laser-tissue interactions and medical applications.
Download or read book Laser Surface Interactions for New Materials Production written by Antonio Miotello and published by Springer Science & Business Media. This book was released on 2009-12-05 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an overview on nanosecond and ultra-short laser-induced phenomena and the related diagnostics. It grew from the lectures of the International School "Laser-surface interactions for new materials production" held in July 2008.
Download or read book Ferroelectric Thin Films written by Masanori Okuyama and published by Springer Science & Business Media. This book was released on 2005-02-22 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ferroelectric thin films continue to attract much attention due to their developing applications in memory devices, FeRAM, infrared sensors, piezoelectric sensors and actuators. This book, aimed at students, researchers and developers, gives detailed information about the basic properties of these materials and the associated device physics. The contributing authors are acknowledged experts in the field.
Download or read book Non traditional Micromachining Processes written by Golam Kibria and published by Springer. This book was released on 2017-03-07 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a complete coverage of micromachining processes from their basic material removal phenomena to past and recent research carried by a number of researchers worldwide. Chapters on effective utilization of material resources, improved efficiency, reliability, durability, and cost effectiveness of the products are presented. This book provides the reader with new and recent developments in the field of micromachining and microfabrication of engineering materials.
Download or read book Crystalline Silicon written by Sukumar Basu and published by BoD – Books on Demand. This book was released on 2011-07-27 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: The exciting world of crystalline silicon is the source of the spectacular advancement of discrete electronic devices and solar cells. The exploitation of ever changing properties of crystalline silicon with dimensional transformation may indicate more innovative silicon based technologies in near future. For example, the discovery of nanocrystalline silicon has largely overcome the obstacles of using silicon as optoelectronic material. The further research and development is necessary to find out the treasures hidden within this material. The book presents different forms of silicon material, their preparation and properties. The modern techniques to study the surface and interface defect states, dislocations, and so on, in different crystalline forms have been highlighted in this book. This book presents basic and applied aspects of different crystalline forms of silicon in wide range of information from materials to devices.
Download or read book Nano Microscale Heat Transfer written by Zhuomin M. Zhang and published by Springer Nature. This book was released on 2020-06-23 with total page 780 pages. Available in PDF, EPUB and Kindle. Book excerpt: This substantially updated and augmented second edition adds over 200 pages of text covering and an array of newer developments in nanoscale thermal transport. In Nano/Microscale Heat Transfer, 2nd edition, Dr. Zhang expands his classroom-proven text to incorporate thermal conductivity spectroscopy, time-domain and frequency-domain thermoreflectance techniques, quantum size effect on specific heat, coherent phonon, minimum thermal conductivity, interface thermal conductance, thermal interface materials, 2D sheet materials and their unique thermal properties, soft materials, first-principles simulation, hyperbolic metamaterials, magnetic polaritons, and new near-field radiation experiments and numerical simulations. Informed by over 12 years use, the author’s research experience, and feedback from teaching faculty, the book has been reorganized in many sections and enriched with more examples and homework problems. Solutions for selected problems are also available to qualified faculty via a password-protected website.• Substantially updates and augments the widely adopted original edition, adding over 200 pages and many new illustrations;• Incorporates student and faculty feedback from a decade of classroom use;• Elucidates concepts explained with many examples and illustrations;• Supports student application of theory with 300 homework problems;• Maximizes reader understanding of micro/nanoscale thermophysical properties and processes and how to apply them to thermal science and engineering;• Features MATLAB codes for working with size and temperature effects on thermal conductivity, specific heat of nanostructures, thin-film optics, RCWA, and near-field radiation.
