Download or read book Experimental Investigation of Overall Effectiveness and Coolant Jet Interactions on a Fully Cooled C3X Turbine Vane written by John W. McClintic and published by . This book was released on 2013 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study focused on experimentally measuring the performance of a fully cooled, scaled up C3X turbine vane. Experimental measurements focused on investigating row-to-row interactions of coolant jets and the contributions of external film cooling and internal impingement cooling to overall cooling effectiveness. Overall effectiveness was experimentally measured using a thermally scaled, matched Biot number vane model featuring a realistic internal impingement scheme and had normalized surface temperatures that were representative of those found on engine components. A geometrically identical vane was also constructed out of low conductivity polystyrene foam to measure the normalized adiabatic wall temperature, or adiabatic effectiveness of the film cooling configuration. The vanes featured a full coverage film-cooling scheme with a five-row showerhead and 13 total rows of holes containing 149 total coolant holes. This study was the first study to make highly detailed measurements of overall effectiveness on a fully-cooled vane model and expands on previous studies of adiabatic and overall effectiveness on the showerhead and single rows of holes on a matched Biot vane by considering a fully cooled configuration to determine if the results from these previous studies also hold for a fully cooled configuration. Additionally, velocity and thermal fields were measured just upstream of two different suction side rows of holes in order to study the effect of introducing upstream coolant injection. The effects of mainstream turbulence and span-wise location were examined and at the downstream row of holes, the contributions of different rows of holes to the approach flow were compared. This study was the first to measure mean and fluctuating velocity data on the suction side of a turbine vane with upstream coolant injection. Understanding the effects of how upstream injection affects the performance of downstream rows of holes is critical to understanding the film cooling performance on a fully cooled turbine airfoil.
Download or read book Experimental and Computational Investigation of Film Cooling on a Large Scale C3X Turbine Vane Including Conjugate Effects written by Thomas Earl Dyson and published by . This book was released on 2012 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study focused on the improvement of film cooling for gas turbine vanes using both computational and experimental techniques. The experimental component used a matched Biot number model to measure scaled surface temperature (overall effectiveness) distributions representative of engine conditions for two new configurations. One configuration consisted of a single row of holes on the pressure surface while the other used numerous film cooling holes over the entire vane including a showerhead. Both configurations used internal impingement cooling representative of a 1st vane. Adiabatic effectiveness was also measured. No previous studies had shown the effect of injection on the mean and fluctuating velocity profiles for the suction surface, so measurements were made at two locations immediately upstream of film cooling holes from the fully cooled cooling configuration. Different blowing conditions were evaluated. Computational tools are increasingly important in the design of advanced gas turbine engines and validation of these tools is required prior to integration into the design process. Two film cooling configurations were simulated and compared to past experimental work. Data from matched Biot number experiments was used to validate the overall effectiveness from conjugate simulations in addition to adiabatic effectiveness. A simulation of a single row of cooling holes on the suction side also gave additional insight into the interaction of film cooling jets with the thermal boundary layer. A showerhead configuration was also simulated. The final portion of this study sought to evaluate the performance of six RANS models (standard, realizable, and renormalization group k-[epsilon]; standard k-[omega]; k-[omega] SST; and Transition SST) with respect to the prediction of thermal boundary layers. The turbulent Prandtl number was varied to test a simple method for improvement of the thermal boundary layer predictions.
Download or read book Experimental Investigation of External Water spray Cooling in a Turbojet Engine Utilizing Several Injection Configurations Including Orifices in the Rotor blade Bases written by Roy A. McKinnon and published by . This book was released on 1955 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Coup d il impartial written by and published by . This book was released on 1787 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sweeping Jet Film Cooling written by Mohammad Arif Hossain and published by . This book was released on 2020 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbine is an integrated part of modern aviation and power generation industry. The thermal efficiency of a gas turbine strongly depends on the turbine inlet temperature (TIT), and the turbine designers are continuously pushing the TIT to a higher value. Due to the increased freedom in additive manufacturing, the complex internal and external geometries of the turbine blade can be leveraged to utilize innovative cooling designs to address some of the shortcomings of current cooling technologies. The sweeping jet film cooling has shown some promise to be an effective method of cooling where the coolant can be brought very close to the blade surface due to its sweeping nature. A series of experiments were performed using a row of fluidic oscillators on a flat plate. Adiabatic cooling effectiveness, convective heat transfer coefficient, thermal field, and discharge coefficient were measured over a range of blowing ratios and freestream turbulence. Results were compared with a conventional shaped hole (777-hole), and the sweeping jet hole shows improved cooling performance in the lateral direction. Numerical simulation also confirmed that the sweeping jet creates two alternating vortices that do not have mutual interaction in time. When the jet sweeps to one side of the hole exit, it acts as a vortex generator as it interacts with the mainstream ow. This prevents the formation of the counter-rotating vortex pair (CRVP) and allows the coolant to spread in the lateral direction. The results obtained from the low speed at plate tests were utilized to design the sweeping jet film cooling hole for more representative turbine vane geometry. Experiments were performed in a low-speed linear cascade facility. Results showed that the sweeping jet hole has higher cooling effectiveness in the near hole region compared to the shaped hole at high blowing ratios. Next, a detailed experimental investigation of sweeping jet film cooling on the suction surface of a near engine scale transonic nozzle guide vane at an engine relevant Mach number (Ma = 0.8) and Reynolds number (Re = 1x10e6) to determine the effect of compressibility. The heat transfer measurements were conducted with a transient IR method, and the convective heat transfer coefficient (HTC) and adiabatic film cooling effectiveness were estimated using a dual linear regression technique (DLRT). Aerodynamic loss measurements were also performed at an exit plane downstream of the vane cascade. Finally, a comprehensive design integration of sweeping jet film hole was carried out in a Direct Metal Laser Sintering (DMLS) enabled engine scale nozzle guide vane and experimental investigation of overall cooling effectiveness at engine relevant temperature conditions were assessed. The systematic evolution of a sweeping jet film cooling hole design from a large scale flat plate to an engine scale nozzle guide vane has been presented.
Download or read book Film Cooling Effectiveness on a Turbine Vane in Transonic Conditions written by Isabella Gayoso and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this experiment, measurements of the overall cooling effectiveness for a film cooled turbine vane airfoil in a high-speed cascade were obtained using infrared thermography. The vane used was the NASA C3X with impingement holes (showerhead cooling) and convective cooling holes on both the suction and pressure side. This work was done in the Mechanical Engineering Department's Experimental and Computational Convection Lab and used the high-speed cascade capability of the lab. The rationale for conducting this work was to obtain experimental data on film cooling effectiveness in a turbine vane in engine-like conditions at transonic speeds. Previous work has been done at subsonic speeds, but few pieces of literature examine this parameter at transonic speeds. The data can then be used to validate or compare to CFD models and to better understand what happens to the vane temperature distribution during engine operation. This understanding could inform the design of film cooling holes to reduce thermal strain "hot spots" which lead to failure of the vane. The results showed that trends for values of overall film effectiveness were as expected in this experiment, such as increases in blowing ratio correlating to increases in overall film effectiveness. However, the blowing ratios used in this study were not as high as values studied previously, indicating a need for more data on overall film effectiveness at transonic speeds.
Download or read book Experimental Measurement of Overall Effectiveness and Internal Coolant Temperatures for a Film Cooled Gas Turbine Airfoil with Internal Impingement Cooling written by Randall Paul Williams and published by . This book was released on 2012 with total page 258 pages. Available in PDF, EPUB and Kindle. Book excerpt: A scaled-up gas turbine vane model was constructed in such a way to achieve a Biot number (Bi) representative of an actual engine component, and experiments were performed to collect temperature data which may be used to validate computational fluid dynamics (CFD) codes used in the design of gas turbine cooling schemes. The physical model incorporated an internal impingement plate to provide cooling on the inner wall surface, and film cooling over the external surface was provided by a single row of holes located on the suction side of the vane. A single row of holes was chosen to simplify the operating condition and test geometry for the purpose of evaluating CFD predictions. Thermocouples were used to measure internal gas temperatures and internal surface temperatures over a range of coolant flow rates, while infra-red thermography was used to measure external surface temperatures. When Bi is matched to an actual engine component, these measured temperatures may be normalized relative to the coolant temperature and mainstream gas temperature to determine the overall cooling effectiveness, which will be representative of the real engine component. Measurements were made to evaluate the overall effectiveness resulting from internal impingement cooling alone, and then with both internal impingement cooling and external film cooling as the coolant flow rate was increased. As expected, with internal impingement cooling alone, both internal and external wall surfaces became colder as the coolant flow rate was increased. The addition of film cooling further increased the overall effectiveness, particularly at the lower and intermediate flow rates tested, but provided little benefit at the highest flow rates. An optimal jet momentum flux ratio of I=1.69 resulted in a peak overall effectiveness, although the film effectiveness was shown to be low under these conditions. The effect of increasing the coolant-to-mainstream density ratio was evaluated at one coolant flow rate and resulted in higher values of overall cooling effectiveness and normalized internal temperatures, throughout the model. Finally, a 1-dimensional heat transfer analysis was performed (using a resistance analogy) in which overall effectiveness with film cooling was predicted from measurements of film effectiveness and overall effectiveness without film cooling. This analysis tended to over-predict overall effectiveness, at the lowest values of the jet momentum flux ratio, while under-predicting it at the highest values.
Download or read book Experimental Study of Film Cooling and Heat Transfer on a Gas Turbine Vane with Shaped Holes written by Tarek Elnady and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Study of Vane Heat Transfer and Film Cooling at Elevated Levels of Turbulence written by Forrest E. Ames and published by . This book was released on 1996 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Investigations of Platform Film Cooling in Highly Loaded Turbine Vanes written by Martin Kunze and published by . This book was released on 2013-12-11 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Comparison of the Cooling Effectiveness of Superheated Steam and Hot Air in Internal Turbine Blade Cooling written by Ramakrishnan Pudupatty and published by . This book was released on 1998 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nozzle Guide Vane Sweeping Jet Impingement Cooling written by Lucas Agricola and published by . This book was released on 2018 with total page 91 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sweeping jet impingement cooling was investigated in a gas turbine nozzle guide vane design with an engine-relevant Biot number of 0.3. Sweeping jets were created with fluidic oscillators and were compared to steady jets produced by cylindrical orifices (with length-to-diameter ratio of 1), the current state-of-the-art in engine designs. Experiments were performed in a low speed linear cascade with additively manufactured test pieces. The impingement cooling geometries were examined at multiple coolant mass flow rates and freestream turbulence intensities. The overall effectiveness of each cooling geometry was calculated using thermocouple measurements of the freestream and coolant temperatures, and infrared thermography measurements of the vane external surface temperature. A computational thermal inertia technique was used to determine the internal Nusselt numbers. The heat transfer provided by steady impinging jets produced a higher overall effectiveness and Nusselt number in the leading edge geometry. The sweeping jets provided more uniform heat transfer, reducing thermal gradients near the stagnation point. Pressure drop across each jet geometry was measured at a range of applicable mass flow rates. Fluidic oscillators were shown to create similar pressure drop to circular orifice holes when additive manufacturing abilities were fully incorporated in the nozzle guide vane internal cooling designs.
Download or read book Integration of Cooling System with an Experimental Rig for Film Effectiveness Measurement Using a Full stage High pressure Turbine written by Jacob Ward Harral and published by . This book was released on 2005 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt: Abstract: Increasing the efficiency in gas turbine engines requires constant improvement in the design tools currently available to the industry. One area for potential increases in efficiency deals with the film-cooling effectiveness in the high-pressure turbine section of the engine and the push to increase the temperature at the inlet of the turbine. Modeling of film-cooling effectiveness for incorporation into advanced CFD codes to be used for film effectiveness predictions and subsequent design of advanced engines is currently a major activity within the engine community. For the codes to be implemented as design tools one must gain confidence in their validity. One method that has been used for this purpose is to compare predictions obtained using these codes with experimental results obtained under as realistic conditions as is possible within the confines of controlled laboratory experiments. Under support of the NASA/DoD URETI, the OSU GTL has undertaken the task of performing detailed surface-pressure and surface heat-transfer measurements on the vane surfaces, on the blade surfaces, and on the stationary shroud of a fully cooled high-pressure turbine stage operating at design corrected conditions. Several significant changes have been made to the OSU Gas Turbine Laboratory blowdown turbine facility and to the operating mode of that facility in order to make film effectiveness measurements. One of the major facility changes was the incorporation of a coolant gas supply system (LCF) into the facility. The major changes in operating mode involved operating in blowdown mode instead of shock tube mode. In order to achieve this major change in operating procedure, it was necessary to incorporate a resistance heater into the rig just ahead of the high-pressure turbine vane inlet so that a resistance heater instead of the reflected shock could heat the test gas. The next major task was to sequence the main test gas flow with the coolant gas flow so that one could achieve the proper flow physics. This thesis will focus on the operation and integration of the LCF into the blowdown facility and on the experimental results acquired during the initial film-cooling experiment. Operation of the LCF is divided into three distinct areas: fast acting valve operation and sequencing with the main facility fast acting valve, cooling cycles, and facility controls. Successful integration of the LCF has been achieved and will be illustrated by the results of the initial film-cooling experiment. Through these experimental results and accompanying uncertainty analysis conducted as part of this thesis significant knowledge has been gained and will be applied to future film-cooling measurement programs. With the demonstrated successful operation of the OSU turbine test facility in conjunction with the LCF, the OSU GTL is capable of conducting the critical experiments necessary to provide critical verification information for ongoing film effectiveness modeling and CFD code development.
Download or read book Prediction of Film Cooling on Gas Turbine Airfoils written by and published by . This book was released on 1994 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Prediction and Measurement of Film Cooling Effectiveness for a First stage Turbine Vane Shroud written by D. Granser and published by . This book was released on 1990 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: After compressor discharge air has initially been used to cool the heat shields of the hot gas inlet casing, it can subsequently be employed for film cooling of the first-stage vane shrouds. Since the flow field near these shrouds is three-dimensional, the film cooling effectiveness cannot be predicted correctly by common two-dimensional codes. The secondary flow transports the film from the pressure side to the suction side where it can even climb up the airfoil to cool its trailing section. Such film cooling effectiveness was first investigated experimentally in a linear vane cascade at atmospheric pressure. The temperatures and static pressure levels at the adiabatic shrouds, as well as the temperature measurements within the vane cascade, are reported for different cooling film blowing rates. In addition, the secondary flow was analysed numerically using a partially-parabolic computer code for 3D viscous flows. It involves mutual interaction of the boundary layer with the mainstream. The secondary flow can also be modelled with this algorithm, which requires less numerical effort than solving the fully 3D elliptic flow equations. The numerical results of the experiment and numerical predictions are compared. In addition, the application of these results to a high-temperature gas turbine is presented.
Download or read book Suction Side Roughness Effects on Film Cooling Heat Transfer on a Turbine Vane written by and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study was conducted in a simulated three vane linear cascade to determine the effects of surface roughness and film cooling on the heat transfer coefficient distribution in the region downstream of the first row of suction side coolant holes. Suction side film cooling was operated in the range 0 less than M less than 1.4. The showerhead was tested at M(sub sh) = 1.6. In addition to the completely smooth condition, simulated airfoil roughness was used upstream of the coolant holes, downstream of the coolant holes, and both upstream and downstream of the coolant holes. Two levels of mainstream turbulence intensity were tested. The heat transfer measurements were conducted by application of a uniform heat flux in the region downstream of the coolant holes. The resulting surface temperature distributions were measured with infrared thermography. Because the upstream region was unheated, the influence of film cooling on the heat transfer coefficient was due to only to hydrodynamic effects and not thermal effects. The coolant to mainstream density ratio of the majority of the experiments was unity; however, a single experiment was conducted at a density ratio of DR = 1.6 to determine how the coolant to mainstream density ratio affects heat transfer. Net heat flux reduction calculations were performed by combining the heat transfer coefficient measurements of the present study with adiabatic effectiveness measurements of a separate study. In order to gain insight into the hydrodynamics that affect the heat transfer, boundary layer measurements were conducted using hot-wire anemometry.
Download or read book Detailed film cooling effectiveness and three component velocity field measurements on a first stage turbine vane subject to high freestream turbulence written by Marcus Damian Polanka and published by . This book was released on 1999 with total page 718 pages. Available in PDF, EPUB and Kindle. Book excerpt:
