Download or read book Experimental and Numerical Investigation of Turbulent Flow and Heat mass Transfer in a Two pass Trapezoidal Channel with Turbulence Promoters written by Sung Hyuk Oh and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Experiments and numerical predictions were conducted to study heat (mass) transfer characteristics in a two-pass trapezoidal channel simulating the cooling passage of a gas turbine blade. Three different rib configurations were tested for the air entering the smaller cross section of the trapezoidal channel as well as the larger cross section of the trapezoidal channel at four different Reynolds numbers of 9,400, 16,800, 31,800, and 57,200. (+) 60[degree] ribs, ( -- ) 60[degree] ribs and 60[degree] V-shaped ribs were attached on both the top and bottom walls in parallel sequence. A naphthalene sublimation technique was used, and the heat and mass transfer analogy was applied to convert the mass transfer coefficients to heat transfer coefficients. Numerical predictions of three-dimensional flow and heat transfer also were performed for the trapezoidal channel with and without 90[degree] ribs tested by Lee et al. (2007). Reynolds stress turbulence model (RSM) in the FLUENT CFD code was used to calculate the heat transfer coefficients and flow fields at Re = 31,800. The results showed that the combined effects of the rib angle, rib orientation, and the sharp 180[degree] turn significantly affected the heat (mass) transfer distributions. The secondary flows induced by the sharp 180[degree] turn and the angled or V-shaped ribs played a very prominent role in heat (mass) transfer enhancements. The heat (mass) transfer enhancements and the pressure drops across the turn for 60[degree] V-shaped ribs had the highest values, then came the case of (+) 60[degree] ribs, and the heat (mass) transfer enhancements and the friction factor ratios for ( -- ) 60[degree] ribs was the lowest. However, comparing ( -- ) 60[degree] ribs with the 90[degree] ribs, ( -- ) 60[degree] ribs produced higher heat (mass) transfer enhancements than the 90[degree] ribs, as results of the secondary flow induced by the ( -- ) 60[degree] ribs. The overall average heat (mass) transfer for the larger inlet cases was always higher than that for the smaller inlet cases in the ribbed trapezoidal channel. Considering the thermal performance comparisons of the (+) 60[degree] ribs, the ( -- ) 60[degree] ribs, and 60[degree] V-shaped ribs for the smaller inlet cases, the highest thermal performance was produced by the ( -- ) 60[degree] ribs, and the 60[degree] V-shaped ribs and the (+) 60[degree] ribs had almost the same levels of the thermal performance since the 60[degree] V-shaped ribs produced the highest heat (mass) transfer enhancement but also produced highest pressure drops. For the larger inlet cases, the (+) 60[degree] ribs produced the highest values, then came the case of the 60[degree] V-shaped ribs, and the thermal performance for the ( -- ) 60[degree] ribs was the lowest. The Reynolds stress model (RSM) showed well flow fields and heat transfer distributions but underpredicted average Nusselt number ratios.

Download or read book Engineering Turbulence Modelling and Experiments 4 written by D. Laurence and published by Elsevier. This book was released on 1999-04-14 with total page 975 pages. Available in PDF, EPUB and Kindle. Book excerpt: These proceedings contain the papers presented at the 4th International Symposium on Engineering Turbulence Modelling and Measurements held at Ajaccio, Corsica, France from 24-26 May 1999. It follows three previous conferences on the topic of engineering turbulence modelling and measurements. The purpose of this series of symposia is to provide a forum for presenting and discussing new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. Turbulence is still one of the key issues in tackling engineering flow problems. As powerful computers and accurate numerical methods are now available for solving the flow equations, and since engineering applications nearly always involve turbulence effects, the reliability of CFD analysis depends more and more on the performance of the turbulence models. Successful simulation of turbulence requires the understanding of the complex physical phenomena involved and suitable models for describing the turbulent momentum, heat and mass transfer. For the understanding of turbulence phenomena, experiments are indispensable, but they are equally important for providing data for the development and testing of turbulence models and hence for CFD software validation.

Download or read book Engineering Turbulence Modelling and Experiments 5 written by W. Rodi and published by Elsevier. This book was released on 2002-08-21 with total page 1029 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbulence is one of the key issues in tackling engineering flow problems. As powerful computers and accurate numerical methods are now available for solving the flow equations, and since engineering applications nearly always involve turbulence effects, the reliability of CFD analysis depends increasingly on the performance of the turbulence models. This series of symposia provides a forum for presenting and discussing new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. The papers in this set of proceedings were presented at the 5th International Symposium on Engineering Turbulence Modelling and Measurements in September 2002. They look at a variety of areas, including: Turbulence modelling; Direct and large-eddy simulations; Applications of turbulence models; Experimental studies; Transition; Turbulence control; Aerodynamic flow; Aero-acoustics; Turbomachinery flows; Heat transfer; Combustion systems; Two-phase flows. These papers are preceded by a section containing 6 invited papers covering various aspects of turbulence modelling and simulation as well as their practical application, combustion modelling and particle-image velocimetry.

Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1993 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Turbulence and Interactions written by Michel Deville and published by Springer Nature. This book was released on 2021-02-16 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a snapshot of the state-of-art in the field of turbulence modeling, with an emphasis on numerical methods. Topics include direct numerical simulations, large eddy simulations, compressible turbulence, coherent structures, two-phase flow simulation and many more. It includes both theoretical contributions and experimental works, as well as chapters derived from keynote lectures, presented at the fifth Turbulence and Interactions Conference (TI 2018), which was held on June 25-29 in Martinique, France. This multifaceted collection, which reflects the conference ́s emphasis on the interplay of theory, experiments and computing in the process of understanding and predicting the physics of complex flows and solving related engineering problems, offers a timely guide for students, researchers and professionals in the field of applied computational fluid dynamics, turbulence modeling and related areas.

Download or read book Experimental and Numerical Investigations for an Advanced Modeling of Two phase Flow and Mass Transfer on Column Trays written by Vineet Vishwakarma and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Numerical Experiments in Homogeneous Turbulence written by Robert Sugden Rogallo and published by . This book was released on 1981 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Experimental and Numerical Investigation of Three dimensional Turbulent Flow with Decaying Swirl written by M. R. Casey and published by . This book was released on 1988 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Investigation of Turbulent Flow in a Two dimensional Channel written by John Laufer and published by . This book was released on 1950 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt: A detailed exploration of the turbulent flow characteristics in a two-dimensional channel is presented. The measurements were made at three Reynolds numbers, 12,300, 30,800, and 61,600, based on the half width of the channel and the maximum mean velocity. A channel of 5-inch width and 12:1 aspect ratio was used for the investigation.

Download or read book Numerical Investigation of Separated Transonic Turbulent Flows with a Multiple time scale Turbulence Model written by S. W. Kim and published by . This book was released on 1990 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book New trends in turbulence Turbulence nouveaux aspects written by M. Lesieur and published by Springer Science & Business Media. This book was released on 2003-07-01 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: Following a longstanding tradition of the Les Houches Summer Schools, this book uses a pedagogically presented and accessible style to treat 2D and 3D turbulence from the experimental, theoretical and computational points of view.

Download or read book Multiscale and Multiresolution Approaches in Turbulence written by Pierre Sagaut and published by Imperial College Press. This book was released on 2006 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique book gives a general unified presentation of the use of the multiscale/multiresolution approaches in the field of turbulence. The coverage ranges from statistical models developed for engineering purposes to multiresolution algorithms for the direct computation of turbulence. It provides the only available up-to-date reviews dealing with the latest and most advanced turbulence models (including LES, VLES, hybrid RANS/LES, DES) and numerical strategies. The book aims at providing the reader with a comprehensive description of modern strategies for turbulent flow simulation, ranging from turbulence modeling to the most advanced multilevel numerical methods. Sample Chapter(s). Chapter 1: A Brief Introduction to Turbulence (4,125 KB). Contents: A Brief Introduction to Turbulence; Turbulence Simulation and Scale Separation; Statistical Multiscale Modeling; Multiscale Subgrid Models: Self-Adaptivity; Structural Multiscale Subgrid Models: Small Scale Estimations; Unsteady Turbulence Simulation on Self-Adaptive Grids; Global Hybrid RANS/LES Methods; Zonal RANS/LES Methods. Readership: Researchers and engineers in academia and industry in aerospace, automotive and other aerodynamics-oriented fields; masters-level students in fluid mechanics, computational fluid dynamics and applied mathematics.

Download or read book Theoretical Chemical Engineering Abstracts written by and published by . This book was released on 1975 with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Experimental and Numerical Investigation of Double diffusive Convection in a Stratified Fluid Subjected to Lateral Heating written by Robert Andrew Hart and published by . This book was released on 1997 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Numerical Investigation of an Internal Layer in Turbulent Flow Over a Curved Hill written by S. W. Kim and published by . This book was released on 1989 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Engineering Turbulence Modelling and Experiments 5 written by W. Rodi and published by Elsevier Science. This book was released on 2002-09-04 with total page 1028 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbulence is one of the key issues in tackling engineering flow problems. As powerful computers and accurate numerical methods are now available for solving the flow equations, and since engineering applications nearly always involve turbulence effects, the reliability of CFD analysis depends increasingly on the performance of the turbulence models. This series of symposia provides a forum for presenting and discussing new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. The papers in this set of proceedings were presented at the 5th International Symposium on Engineering Turbulence Modelling and Measurements in September 2002. They look at a variety of areas, including: Turbulence modelling; Direct and large-eddy simulations; Applications of turbulence models; Experimental studies; Transition; Turbulence control; Aerodynamic flow; Aero-acoustics; Turbomachinery flows; Heat transfer; Combustion systems; Two-phase flows. These papers are preceded by a section containing 6 invited papers covering various aspects of turbulence modelling and simulation as well as their practical application, combustion modelling and particle-image velocimetry.

Download or read book A Numerical Investigation of Turbulent Channel Flow Using a Second Order Vorticity Turbulence Closure written by Sami Ainane and published by . This book was released on 1989 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt: