Download or read book Experimental and Analytical Study of Full depth Precast prestressed Concrete Deck Panels for Highway Bridges written by Scott M. Markowski and published by . This book was released on 2005 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Evaluation of Full Depth Precast prestressed Concrete Bridge Deck Panels written by Mohsen A. Issa and published by . This book was released on 2002 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: A literature review concerning the objectives of the project was completed. A significant number of published papers, reports, etc., were examined to determine the effectiveness of full depth precast panels for bridge deck replacement. A detailed description of the experimental methodology was developed which includes design and fabrication of the panels and assembly of the bridge. The design and construction process was carried out in cooperation with the project Technical Review Panel. The major components of the bridge deck system were investigated. This includes the transverse joints and the different materials within the joint as well as composite action. The materials investigated within the joint were polymer concrete, non-shrink grout, and set-45 for the transverse joint. The transverse joints were subjected to direct shear tests, direct tension tests, and flexure tests. These tests exhibited the excellent behavior of the system in terms of strength and failure modes. Shear key tests were also conducted. The shear connection study focused on investigating the composite behavior of the system based on varying the number of shear studs within a respective pocket as well as varying the number of pockets within a respective panel. The results indicated that this shear connection is extremely efficient in rendering the system under full composite action. Finite element analysis was conducted to determine the behavior of the shear connection prior to initiation of the actual full scale tests. In addition, finite element analysis was also performed with respect to the transverse joint tests in an effort to determine the behavior of the joints prior to actual testing. The most significant phase of the project was testing a full-scale model. The bridge was assembled in accordance with the procedures developed as part of the study on full-depth precast panels and the results obtained through this research. The system proved its effectiveness in withstanding the applied loading that exceeded eight times the truck loading in addition to the maximum negative and positive moment application. Only hairline cracking was observed in the deck at the maximum applied load. Of most significance was the fact that full composite action was achieved between the precast panels and the steel supporting system, and the exceptional performance of the transverse joint between adjacent panels.

Download or read book Experimental and Analytical Investigation of Full depth Precast Deck Panels on Prestressed I girders written by Sean Robert Sullivan and published by . This book was released on 2008 with total page 81 pages. Available in PDF, EPUB and Kindle. Book excerpt: A bridge with precast bridge deck panels was built at the Virginia Tech Structures Laboratory to examine constructibility issues, creep and shrinkage behavior, and strength and fatigue performance of transverse joints, different types of shear connectors, and different shear pocket spacings. The bridge consisted of two AASHTO type II girders, 40 ft long and simply supported, and five precast bridge deck panels. Two of the transverse joints were epoxied male-female joints and the other two transverse joints were grouted female-female joints. Two different pocket spacings were studied: 4 ft pocket spacing and 2 ft pocket spacing. Two different shear connector types were studied: hooked reinforcing bars and a new shear stud detail that can be used with concrete girders. The construction process was well documented. The changes in strain in the girders and deck were examined and compared to a finite element model to examine the effects of differential creep and shrinkage. After the finite element model verification study, the model was used to predict the long term stresses in the deck and determine if the initial level of post-tensioning was adequate to keep the transverse joints in compression throughout the estimated service life of the bridge. Cyclic loading tests and flexural strength tests were performed to examine performance of the different pocket spacings, shear connector types and transverse joint configurations. A finite element study examined the performance of the AASHTO LRFD shear friction equation for the design of the horizontal shear connectors. The initial level of post-tensioning in the bridge was adequate to keep the transverse joints in compression throughout the service life of the bridge. Both types of pocket spacings and shear connectors performed exceptionally well. The AASHTO LRFD shear friction equation was shown to be applicable to deck panel systems and was conservative for determining the number of shear connectors required in each pocket. A recommended design and detailing procedure was developed for the shear connectors and shear pockets.

Download or read book Full depth Precast Concrete Bridge Deck Panel Systems written by Sameh S. Badie and published by Transportation Research Board. This book was released on 2008 with total page 119 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental and Analytical Study of Concrete Bridge Decks Constructed with FRP Stay in place Forms and FRP Grid Reiforcing written by David Allan Dieter and published by . This book was released on 2002 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Structural Performance of a Full depth Precast Concrete Bridge Deck System written by Thomas Mander and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Throughout the United States accelerated bridge construction is becoming increasingly popular to meet growing transportation demands while keeping construction time and costs to a minimum. This research focuses on eliminating the need to form full-depth concrete bridge deck overhangs, accelerating the construction of concrete bridge decks, by using full-depth precast prestressed concrete deck panels. Full-depth precast overhang panels in combination with cast-in-place (CIP) reinforced concrete are experimentally and analytically investigated to assess the structural performance. Experimental loaddeformation behavior for factored AASHTO LRFD design load limits is examined followed by the collapse capacity of the panel-to-panel seam that exists in the system. Adequate strength and stiffness of the proposed full-depth panels deem the design safe for implementation for the Rock Creek Bridge in Fort Worth, Texas. New failure theories are derived for interior and exterior bridge deck spans as present code-based predictions provide poor estimates of the ultimate capacity. A compound shear-flexure failure occurs at interior bays between the CIP topping and stay-in-place (SIP) panel. Overhang failure loads are characterized as a mixed failure of flexure on the loaded panel and shear at the panel-to-panel seam. Based on these results design recommendations are presented to optimize the reinforcing steel layout used in concrete bridge decks.

Download or read book Investigation of Prestressed Concrete for Highway Bridges written by Narbey Khachaturian and published by . This book was released on 1962 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Composite Precast Prestressed Concrete Bridge Slabs written by R.E. Abendroth and published by . This book was released on 1991 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Precast prestressed concrete panels have been used as subdecks in bridge construction in Iowa and other states. To investigate the performance of these types of composite slabs at locations adjacent to abutment and pier diaphragms in skewed bridges, a research project which involved surveys of design agencies and precast producers, field inspections of existing bridges, analytical studies, and experimental testing was conducted. The survey results from the design agencies and panel producers showed that standardization of precast panel construction would be desirable, that additional inspections at the precast plant and at the bridge site would be beneficial, and that some form of economical study should be undertaken to determine actual cost savings associated with composite slab construction. Three bridges in Hardin County, Iowa were inspected to observe general geometric relationships, construction details, and to note the visual condition of the bridges. Hairline cracks beneath several of the prestressing strands in many of the precast panels were observed, and a slight discoloration of the concrete was seen beneath most of the strands. Also, some rust staining was visible at isolated locations on several panels. Based on the findings of these inspections, future inspections are recommended to monitor the condition of these and other bridges constructed with precast panel subdecks. Five full-scale composite slab specimens were constructed in the Structural Engineering Laboratory at Iowa State University. One specimen modeled bridge deck conditions which are not adjacent to abutment or pier diaphragms, and the other four specimens represented the geometric conditions which occur for skewed diaphragms of 0, 15, 30, and 40 degrees. The specimens were subjected to wheel loads of service and factored level magnitudes at many locations on the slab surface and to concentrated loads which produced failure of the composite slab. The measured slab deflections and bending strains at both service and factored load levels compared reasonably well with the results predicted by simplified Finite element analyses of the specimens. To analytically evaluate the nominal strength for a composite slab specimen, yield-line and punching shear theories were applied. Yield-line limit loads were computed using the crack patterns generated during an ultimate strength test. In most cases, these analyses indicated that the failure mode was not flexural. Since the punching shear limit loads in most instances were close to the failure loads, and since the failure surfaces immediately adjacent to the wheel load footprint appeared to be a truncated prism shape, the probable failure mode for all of the specimens was punching shear. The development lengths for the prestressing strands in the rectangular and trapezoidal shaped panels was qualitatively investigated by monitoring strand slippage at the ends of selected prestressing strands. The initial strand transfer length was established experimentally by monitoring concrete strains during strand detensioning, and this length was verified analytically by a finite element analysis. Even though the computed strand embedment lengths in the panels were not sufficient to fully develop the ultimate strand stress, sufficient stab strength existed. Composite behavior for the slab specimens was evaluated by monitoring slippage between a panel and the topping slab and by computation of the difference in the flexural strains between the top of the precast panel and the underside of the topping slab at various locations. Prior to the failure of a composite slab specimen, a localized loss of composite behavior was detected. The static load strength performance of the composite slab specimens significantly exceeded the design load requirements. Even with skew angles of up to 40 degrees, the nominal strength of the slabs did not appear to be affected when the ultimate strength test load was positioned on the portion of each slab containing the trapezoidal-shaped panel. At service and factored level loads, the joint between precast panels did not appear to influence the load distribution along the length of the specimens. Based on the static load strength of the composite slab specimens, the continued use of precast panels as subdecks in bridge deck construction is recommended.

Download or read book Analytical and Experimental Investigation of Full depth Precast Concrete Bridge Deck Panel Systems written by Nghi T. Nguyen and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Survey and Analysis of Full Depth Precast Prestressed Concrete Panels for Bridge Deck Replacement written by Ahmad-Talal Idriss and published by . This book was released on 1993 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Stress laminated Wood Bridge Decks written by Michael G. Oliva and published by . This book was released on 1990 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Evaluation of Partial Depth Precast Concrete Deck Panels Subjected to Shear Loading written by John Robert Kintz and published by . This book was released on 2017 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Horizontally curved girder bridges are often utilized for highway interchanges and other projects with restricted right-of-way. The large torsional demands caused by the girder geometry often require these systems to have extensive bracing, typically in the form of cross frames or diaphragms, to increase the torsional stiffness of the girder system during the construction phase. The most critical stage for the bracing is during the deck placement, when the noncomposite girders must resist the full construction load. Partial depth precast concrete panels (PCPs) are prestressed concrete panels used primarily as stay-in-place (SIP) formwork for straight girder systems. They are placed on full-length extruded bedding strips epoxied to the girder top flange, and the remaining depth of the deck is cast above. This is a time-efficient method of construction, and has become an attractive option due to ease of constructability and deck longevity. Although the panels have not been used on horizontally curved girder systems, there is a desire by bridge owners and contractors to use the forms in some curved girder applications. In addition to using the panels on curved girder applications, engaging the in-plane shear stiffness of the panels may lead to significant bracing in both straight and horizontally curved girder applications. A research investigation focused on measuring the behavior of PCPs acting as a shear diaphragm, as well as to develop an adequate connection between the PCPs and the girders was conducted at The University of Texas at Austin. Four PCP connection details were developed and tested at two different bedding strip heights. These connections were designed for a range of capacities, and in-plane shear load was applied until failure using a frame mechanism assembly. The experimental results showed that the connected PCPs had significant shear stiffness and strength, with the panels reaching shear capacities between 91 and 154 kips before failure depending on the connection detail that was utilized. A 46 to 70 percent increase in shear stiffness was also observed when the bedding strip height was reduced from 4 inches to 1⁄2 inch. All panels greatly exceeded the design capacity using the ACI design predictions, with 7 of 8 panels eventually failing due to concrete side face breakout. The eighth PCP failed from weld rupture in which the weld connecting the WT and the girder flange began to unzip.

Download or read book Experimental Evaluation of Full Depth Precast prestressed Concrete Bridge Deck Planes written by Mohsen A. Issa and published by . This book was released on 2002 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Behavior of Full Depth Precast Concrete Deck Panels for Bridge Reconstruction written by Alfred Antonious Yousif and published by . This book was released on 1998 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book State of the art Report on Precast Concrete Systems for Rapid Construction of Bridges written by and published by . This book was released on 2005 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Polymer impregnated Precast Structural Concrete Bridge Deck Panels written by William T. Lockman and published by . This book was released on 1975 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Precast Prestressed Concrete Panel Subdecks in Skewed Bridges written by Robert E. Abendroth and published by . This book was released on 1990 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt: Precast prestressed concrete panels have been used in bridge deck construction in Iowa and many other states. To investigate the performance of these panels at abutment or pier diaphragm locations for bridges with various skew angles, a research program involving both analytical and experimental aspects, is being conducted. This interim report presents the status of the research with respect to four tasks. Task 1 which involves a literature review and two surveys is essentially complete. Task 2 which involved field investigations of three Iowa bridges containing precast panel subdecks has been completed. Based on the findings of these investigations, future inspections are recommended to evaluate potential panel deterioration due to possible corrosion of the prestressed strands. Task 3 is the experimental program which has been established to monitor the behavior of five configurations of full scale composite deck slabs. Three dimensional test and instrumentation frameworks have been constructed to load and monitor the slab specimens. The first slab configuration representing an interior panel condition is being tested and preliminary results are presented for one of these tests in this interim report. Task 4 involves the analytical investigation of the experimental specimens. Finite element methods are being applied to analytically predict the behavior of the test specimens. The first slab configuration representing an interior panel condition is being tested and preliminary results are presented for one of these tests in this interim report. Task 4 involves the analytical investigation of the experimental specimens. Finite element methods are being applied to analytically predict the behavior of the test specimens. The first test configuration of the interior panel condition has been analyzed for the same loads used in the laboratory, and the results are presented herein. Very good correlation between the analytical and experimental results has occurred.