Download or read book Exhaust Particle Characterization for Lean and Stoichiometric DI Vehicles Operating on Ethanol Gasoline Blends written by John M. E. Storey and published by . This book was released on 2012 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Exhaust Particle Characterization for Lean and Stoichiometric DI Vehicles Operating on Ethanol gasoline Blends written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Gasoline direct injection (GDI) engines can offer better fuel economy and higher performance over their port fuel-injected (PFI) counterparts, and are now appearing in increasingly more U.S. and European vehicles. Small displacement, turbocharged GDI engines are replacing large displacement engines, particularly in light-duty trucks and sport utility vehicles, in order for manufacturers to meet the U.S. fuel economy standards for 2016. Furthermore, lean-burn GDI engines can offer even higher fuel economy than stoichiometric GDI engines and have overcome challenges associated with cost-effective aftertreatment for NOx control. Along with changes in gasoline engine technology, fuel composition may increase in ethanol content beyond the current 10% due to the recent EPA waiver allowing 15% ethanol. In addition, the Renewable Fuels Standard passed as part of the 2007 Energy Independence and Security Act (EISA) mandates the use of biofuels in upcoming years. GDI engines are of environmental concern due to their high particulate matter (PM) emissions relative to port-fuel injected (PFI) gasoline vehicles; widespread market penetration of GDI vehicles may result in additional PM from mobile sources at a time when the diesel contribution is declining. In this study, we characterized particulate emissions from a European certified lean-burn GDI vehicle operating on ethanol-gasoline blends. Particle mass and particle number concentration emissions were measured for the Federal Test Procedure urban driving cycle (FTP 75) and the more aggressive US06 driving cycle. Particle number-size distributions and organic to elemental carbon ratios (OC/EC) were measured for 30 MPH and 80 MPH steady-state operation. In addition, particle number concentration was measured during wide open throttle accelerations (WOTs) and gradual accelerations representative of the FTP 75. Fuels included certification gasoline and 10% (E10) and 20% (E20) ethanol blends from the same supplier. The particle mass emissions were approximately 3 and 7 mg/mile for the FTP75 and US06, respectively, with lower emissions for the ethanol blends. The data are compared to a previous study on a U.S.-legal stoichiometric GDI vehicle operating on the same ethanol blends. The lean-burn GDI vehicle emitted a higher number of particles, but had an overall smaller average size. Particle number per mile decreased with increasing ethanol content for the transient tests. For the 30 and 80 mph tests, particle number concentration decreased with increasing ethanol content, although the shape of the particle size distribution remained the same. Engine-out OC/EC ratios were highest for the stoichiometric GDI vehicle with E20, but tailpipe OC/EC ratios were similar for all vehicles.

Download or read book Automotive Emissions Regulations and Exhaust Aftertreatment Systems written by John Kasab and published by SAE International. This book was released on 2020-08-31 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this book is to present a fundamental development of the science and engineering underlying the design of exhaust aftertreatment systems for automotive internal combustion engines. No pre-requisite knowledge of the field is required: our objective is to acquaint the reader, whom we expect to be new to the field of emissions control, with the underlying principles, control methods, common problems, and fuel effects on catalytic exhaust aftertreatment devices. We do this in hope that they can better understand the previous and current generations of emissions control, and improve upon them. This book is designed for the engineer, researcher, designer, student, or any combination of those, who is concerned with the control of automotive exhaust emissions. It includes discussion of theory and fundamentals applicable to hardware development.

Download or read book Encyclopedia of Automotive Engineering written by and published by John Wiley & Sons. This book was released on 2015-03-23 with total page 3888 pages. Available in PDF, EPUB and Kindle. Book excerpt: Erstmals eine umfassende und einheitliche Wissensbasis und Grundlage für weiterführende Studien und Forschung im Bereich der Automobiltechnik. Die Encyclopedia of Automotive Engineering ist die erste umfassende und einheitliche Wissensbasis dieses Fachgebiets und legt den Grundstein für weitere Studien und tiefgreifende Forschung. Weitreichende Querverweise und Suchfunktionen ermöglichen erstmals den zentralen Zugriff auf Detailinformationen zu bewährten Branchenstandards und -verfahren. Zusammenhängende Konzepte und Techniken aus Spezialbereichen lassen sich so einfacher verstehen. Neben traditionellen Themen des Fachgebiets beschäftigt sich diese Enzyklopädie auch mit "grünen" Technologien, dem Übergang von der Mechanik zur Elektronik und den Möglichkeiten zur Herstellung sicherer, effizienterer Fahrzeuge unter weltweit unterschiedlichen wirtschaftlichen Rahmenbedingungen. Das Referenzwerk behandelt neun Hauptbereiche: (1) Motoren: Grundlagen; (2) Motoren: Design; (3) Hybrid- und Elektroantriebe; (4) Getriebe- und Antriebssysteme; (5) Chassis-Systeme; (6) Elektrische und elektronische Systeme; (7) Karosserie-Design; (8) Materialien und Fertigung; (9) Telematik. - Zuverlässige Darstellung einer Vielzahl von Spezialthemen aus dem Bereich der Automobiltechnik. - Zugängliches Nachschlagewerk für Jungingenieure und Studenten, die die technologischen Grundlagen besser verstehen und ihre Kenntnisse erweitern möchten. - Wertvolle Verweise auf Detailinformationen und Forschungsergebnisse aus der technischen Literatur. - Entwickelt in Zusammenarbeit mit der FISITA, der Dachorganisation nationaler Automobil-Ingenieur-Verbände aus 37 Ländern und Vertretung von über 185.000 Ingenieuren aus der Branche. - Erhältlich als stets aktuelle Online-Ressource mit umfassenden Suchfunktionen oder als Print-Ausgabe in sechs Bänden mit über 4.000 Seiten. Ein wichtiges Nachschlagewerk für Bibliotheken und Informationszentren in der Industrie, bei Forschungs- und Schulungseinrichtungen, Fachgesellschaften, Regierungsbehörden und allen Ingenieurstudiengängen. Richtet sich an Fachingenieure und Techniker aus der Industrie, Studenten höherer Semester und Studienabsolventen, Forscher, Dozenten und Ausbilder, Branchenanalysen und Forscher.

Download or read book Physical Characterization of Exhaust Particle Emissions from Late Technology Gasoline Vehicles written by Giorgio Martini and published by . This book was released on 2012 with total page 55 pages. Available in PDF, EPUB and Kindle. Book excerpt: The study assesses the feasibility of introducing the regulated particle number measurement procedure for the regulation of gasoline vehicles, focusing on the established cut-off size of 23 nm. A range of late technology gasoline vehicles were tested under regulated and unregulated test conditions. The results indicated a distinct emission behavior of Direct Injection Gasolines (G-DI), Port Fuel Injection gasolines (PFI) and Diesels equipped with Particulate Filters (DPF), that differed both in terms of the absolute levels but also with respect to the fraction of undetected nano-sized non-volatile particles. The latter was found to be around 20% (based on comparisons with a Condensation Particle Counter (CPC) having a 50% cut-off size at 4.5 nm) for three G-DI vehicles tested, but ranged between 40 and 70% for the two PFIs measured. Interestingly, a relatively large fraction of undetected nanosized was also observed for two late technology DPFs, ranging between 30 and 50%.^To a large extent these differences originate from differences in the size distributions and the relatively blunt shape of the counting efficiency curve of PMP compliant CPCs. Under conditions favouring nucleation mode formation in the dilution tunnel, excessive particle concentrations were detected by the low cut-off size CPCs, and especially the one with a d50 at 4.5 nm, that could exceed those of the PMP compliant CPC by up to one order of magnitude. However, the concentration of these nano-sized particles was found to decrease with increasing the dilution ratio in the first stage of the Volatile Particle Remover (VPR), indicating that this is rather a volatile artifact possibly originating from re-nucleation of evaporated material downstream of the VPR. The study also investigated the potential offered by a range of available approaches to effectively control particle emissions from G-DIs.^These included the use of a Gasoline Particulate Filter (GPF), the introduction of ethanol in the fuel but also an advanced engine concept combining port and direct fuel injection. The GPF system was found to very efficient in controlling particle number emissions under all driving conditions, having no visible impact on carbon dioxide emissions. The use of fuel with hi-ethanol content (75-85%) was also found to be beneficial especially at high engine loads (up to 97% reduction of nonvolatile particle numbers) and during cold start operation (up to 70% reduction). The tests with the "hybrid" G-DI-PFI vehicle indicated that there exists the potential for significant reduction of PM formation through engine measures. The non-volatile particle number emissions of this vehicle remained below the diesel limit over all hot start tests.

Download or read book Alternative Fuels and Mixed Alcohols Testing Program written by Thomas D. Durbin and published by . This book was released on 2016 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ethanol Blend Effects On Direct Injection Spark Ignition Gasoline Vehicle Particulate Matter Emissions written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Direct injection spark-ignition (DISI) gasoline engines can offer better fuel economy and higher performance over their port fuel-injected counterparts, and are now appearing increasingly in more U.S. vehicles. Small displacement, turbocharged DISI engines are likely to be used in lieu of large displacement engines, particularly in light-duty trucks and sport utility vehicles, to meet fuel economy standards for 2016. In addition to changes in gasoline engine technology, fuel composition may increase in ethanol content beyond the 10% allowed by current law due to the Renewable Fuels Standard passed as part of the 2007 Energy Independence and Security Act (EISA). In this study, we present the results of an emissions analysis of a U.S.-legal stoichiometric, turbocharged DISI vehicle, operating on ethanol blends, with an emphasis on detailed particulate matter (PM) characterization. Gaseous species, particle mass, and particle number concentration emissions were measured for the Federal Test Procedure urban driving cycle (FTP 75) and the more aggressive US06 cycle. Particle number-size distributions and organic to elemental carbon ratios (OC/EC) were measured for 30 MPH and 80 MPH steady-state operation. In addition, particle number concentration was measured during wide open throttle accelerations (WOTs) and gradual accelerations representative of the FTP 75. For the gaseous species and particle mass measurements, dilution was carried out using a full flow constant volume sampling system (CVS). For the particle number concentration and size distribution measurements, a micro-tunnel dilution system was employed. The vehicles were fueled by a standard test gasoline and 10% (E10) and 20% (E20) ethanol blends from the same supplier. The particle mass emissions were approximately 3 and 7 mg/mile for the FTP75 and US06, respectively, with lower emissions for the ethanol blends. During steady-state operation, the geometric mean diameter of the particle-number size distribution remained approximately the same (50 nm) but the particle number concentration decreased with increasing ethanol content in the fuel. In addition, increasing ethanol content significantly reduced the number concentration of 50 and 100 nm particles during gradual and WOT accelerations.

Download or read book Nanoparticle Emissions From Combustion Engines written by Jerzy Merkisz and published by Springer. This book was released on 2015-03-19 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on particulate matter emissions produced by vehicles with combustion engines. It describes the physicochemical properties of the particulate matter, the mechanisms of its formation and its environmental impacts (including those on human beings). It discusses methods for measuring particulate mass and number, including the state-of-the-art in Portable Emission Measurement System (PEMS) equipment for measuring the exhaust emissions of both light and heavy-duty vehicles and buses under actual operating conditions. The book presents the authors’ latest investigations into the relations between particulate emission (mass and number) and engine operating parameters, as well as their new findings obtained through road tests performed on various types of vehicles, including those using diesel particulate filter regeneration. The book, which addresses the needs of academics and professionals alike, also discusses relevant European regulations on particulate emissions and highlights selected methods aimed at the reduction of particulate emissions from automobiles.

Download or read book Particulate Measurements and Emissions Characterization of Alternative Fuel Vehicle Exhaust written by Thomas D. Durbin and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Chemical and Biological Characterization of Exhaust Emissions from Vehicles Fueled with Gasoline Alcohol LPG and Diesel written by Sverige Statens naturvårdsverk and published by . This book was released on 1983 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Particulate Measurements and Emissions Characterization of Alternative Fuel Vehicle Exhaust written by Thomas D. Durbin and published by . This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Automobile Exhaust Emission Testing written by H. Klingenberg and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: Differing legislation between the countries or unions of countries involved in pollution reduction has turned gas measuring technology into such an extremely extensive and complex field that only a few specialists in environmental agencies and the automobile industry have a grasp of it. This book is intended as an overview of the basics of exhaust gas measuring technology describing the interrelation between emissions, immissions and the effects of pollutants. It aims to provide experts and students alike with an understanding of the interrelationships and details within this field. The results presented are based on the experience gathered by the author during work spanning more than two decades in the automobile industry.

Download or read book Exhaust Emission Characteristics of Natural Gas Fuelled Vehicles Operating at Lean Air fuel Ratios written by British Columbia Research Council. Physical Technology Division and published by . This book was released on 1986 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Characterization of Exhaust Emissions from Operation of a Light duty Gasoline Vehicle on Alternative source Gasoline Fuels written by Lawrence R. Smith and published by . This book was released on 1983 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book GASOLINE VEHICLE EXHAUST PARTICLE SAMPLING STUDY written by J. Johnson and published by . This book was released on 2003 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: The University of Minnesota collaborated with the Paul Scherrer Institute, the University of Wisconsin (UWI) and Ricardo, Inc to physically and chemically characterize the exhaust plume from recruited gasoline spark ignition (SI) vehicles. The project objectives were: (1) Measure representative particle size distributions from a set of on-road SI vehicles and compare these data to similar data collected on a small subset of light-duty gasoline vehicles tested on a chassis dynamometer with a dilution tunnel using the Unified Drive Cycle, at both room temperature (cold start) and 0 C (cold-cold start). (2) Compare data collected from SI vehicles to similar data collected from Diesel engines during the Coordinating Research Council E-43 project. (3) Characterize on-road aerosol during mixed midweek traffic and Sunday midday periods and determine fleet-specific emission rates. (4) Characterize bulk- and size-segregated chemical composition of the particulate matter (PM) emitted in the exhaust from the gasoline vehicles. Particle number concentrations and size distributions are strongly influenced by dilution and sampling conditions. Laboratory methods were evaluated to dilute SI exhaust in a way that would produce size distributions that were similar to those measured during laboratory experiments. Size fractionated samples were collected for chemical analysis using a nano-microorifice uniform deposit impactor (nano-MOUDI). In addition, bulk samples were collected and analyzed. A mixture of low, mid and high mileage vehicles were recruited for testing during the study. Under steady highway cruise conditions a significant particle signature above background was not measured, but during hard accelerations number size distributions for the test fleet were similar to modern heavy-duty Diesel vehicles. Number emissions were much higher at high speed and during cold-cold starts. Fuel specific number emissions range from 1012 to 3 x 1016 particles/kg fuel. A simple relationship between number and mass emissions was not observed. Data were collected on-road to compare weekday with weekend air quality around the Twin Cities area. This portion of the study resulted in the development of a method to apportion the Diesel and SI contribution to on-road aerosol.

Download or read book Advanced Combustion Technologies for Low Carbon Emissions written by Jun Li and published by Frontiers Media SA. This book was released on 2023-07-10 with total page 119 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Novel Characterization of GDI Engine Exhaust for Gasoline and Mid Level Gasoline Alcohol Blends written by John M. Storey and published by . This book was released on 2014 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: