Download or read book Evaluation of Tensile Tests for Adhesive Bonds written by Suresh Kumar Chandapeta and published by . This book was released on 1984 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evaluation of Tensile Tests for Adhesive Bonds written by GP. Anderson and published by . This book was released on 1985 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile adhesion tests have been used for many years as a quality control tool and to quantify the strength of a bond. The quantity generally reported as the tensile strength is the breaking force per unit bond area (average axial stress at the maximum load). The stress distribution in tensile adhesion tests, as discussed in this report, depends upon many factors such as material properties of the adherend and adhesive and the ratio of bond area to adhesive thickness. Test data are presented which demonstrate that the debond initiation point changes from the bond edge to the center of the bond area as the adhesive thickness is decreased. These test data confirm a prior prediction by the authors.
Download or read book Delamination and Debonding of Materials written by W. Steven Johnson and published by ASTM International. This book was released on 1985 with total page 507 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Evaluation of Equipment and Procedures for Tensile Bond Testing of Concrete Repairs written by Alexander M. Vaysburd and published by . This book was released on 1999 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: If the durability of repaired concrete structures is a primary objective of any repair project, then every effort should be made to ensure adequate bonding between the repair and the existing concrete substrate. A total of 257 partial-depth cores in 77 experimental repairs were tested in Florida, Illinois, and Arizona in order to evaluate the effect of material properties and environmental conditions on the bond between repair and concrete substrate. Three pull-off testing devices were used to determine the bond strengths for each of the experimental repairs. In addition, the testing devices themselves were evaluated by analyzing the magnitude and relative precision of the pull-off strengths, modes of failure, and ease of use in an effort to identify a reliable and practical device for determining in situ tensile bond. The optimum depth of core drilling into the existing substrate was determined by comparing theoretical finite element analysis of failure zone stress distribution with measured test results.
Download or read book Evaluation of a Tensile Test for Adhesion written by G. T. Eden and published by . This book was released on 1969 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Adhesive Joints Formation Characteristics and Testing written by Kash L. Mittal and published by CRC Press. This book was released on 2023-01-27 with total page 407 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume documents the proceedings of the Second International Symposium on Adhesive Joints: Formation, Characteristics and Testing held in Newark, NJ, May 22-24, 2000. Since the first symposium, held in 1982, there had been tremendous research activity dealing with many aspects of adhesive joints. This volume contains a total of 21 papers, which were all properly peer reviewed, revised and edited before inclusion. Therefore, this book is not merely a collection of unreviewed manuscripts, but rather represents information which has passed peer scrutiny. Furthermore, the authors were asked to update their manuscripts, so the information contained in this book should be current and fresh. The book is divided into three parts: 1) General Papers; 2) Evaluation, Analysis and Testing; and 3) Durability Aspects. The topics covered include: molecular brush concepts in enhancing strength of adhesive joints; factors affecting performance of adhesive joints; substrate preparation and modification; interfacial/interphasial aspects; determination of locus of failure; analysis and evaluation of adhesive joints using various techniques; testing of adhesive joints; stress analysis; application of fracture mechanics; durability aspects; accelerated environmental degradation of adhesive joints; solvent uptake; and adhesives with special characteristics. This volume represents a commentary on the current R&D activity in this arena and it should be of great value and interest to anyone interested in adhesive bonding / adhesive joints. Furthermore, this volume contains a number of excellent review/overview articles, which should be of particular value.
Download or read book Analysis and Testing of Adhesive Bonds written by Garron P. Anderson and published by . This book was released on 1977 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Adhesive Joints written by K.L. Mittal and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 912 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume documents the proceedings of the International Symposium on Adhesive Joints: Formation, Characteristics and Testing held under the auspices of the Division of Polymer Mater ials:Science and Engineering of the American Chemical Society in Kansas City, MO, September 12-17, 1982. There is a myriad of applications (ranging from aerospace to surgery) where adhesives are used to join different materials, and concomitantly the understanding of the behavior of adhesive joints becomes very important. There are many factors which can influence the behavior of adhesive joints, e.g., substrate preparation, in terfacial aspects, joint design, mode of stress, external environ ment, etc., and in order to understand the joint behavior in a holistic manner, one must take due cognizance of all these germane factors. So this symposium was planned to address not only how to make acceptable bonds but their characterization, durability and testing were also accorded due consideration.
Download or read book Testing of Adhesives written by Technical Association of the Pulp and Paper Industry. Adhesives Testing Committee and published by . This book was released on 1963 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Testing Adhesive Joints written by Lucas F.M. da Silva and published by John Wiley & Sons. This book was released on 2012-10-22 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Joining techniques such as welding, brazing, riveting and screwing are used by industry all over the world on a daily basis. A further method of joining has also proven to be highly successful: adhesive bonding. Adhesive bonding technology has an extremely broad range of applications. And it is difficult to imagine a product - in the home, in industry, in transportation, or anywhere else for that matter - that does not use adhesives or sealants in some manner. The book focuses on the methodology used for fabricating and testing adhesive and bonded joint specimens. The text covers a wide range of test methods that are used in the field of adhesives, providing vital information for dealing with the range of adhesive properties that are of interest to the adhesive community. With contributions from many experts in the field, the entire breadth of industrial laboratory examples, utilizing different best practice techniques are discussed. The core concept of the book is to provide essential information vital for producing and characterizing adhesives and adhesively bonded joints.
Download or read book Standard Test Method for Tensile Properties of Adhesive Bonds written by ASTM Committee D-14 on Adhesives. Subcommittee D14.80 on Metal Bonding Adhesives and published by . This book was released on 2016 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Adhesively Bonded Joints written by W. Steven Johnson and published by ASTM International. This book was released on 1988 with total page 317 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tensile Testing 2nd Edition written by Joseph R. Davis and published by ASM International. This book was released on 2004 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Methods of Test for Adhesives Adhesively Bonded Joints written by British Standards Institute Staff and published by . This book was released on 1986-01-31 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesives, Test methods, Adhesive-bonded joints, Mechanical testing, Cleavage, Tensile testing, Strength of materials, Breaking load, Bonding, Testing conditions, Test equipment, Test specimens, Dimensions
Download or read book Industrial Applications of Adhesives written by Lucas F. M. da Silva and published by Springer Nature. This book was released on 2020-07-22 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers selected papers presented at the 1st International Conference on Industrial Applications of Adhesives 2020 (IAA 2020). It covers a wide range of topics, including adhesive curing for electronic and automotive industries; adhesive testing with a torsion machine for rigorous mechanical properties determination; joint design using innovative techniques such as the meshless method; design methodologies in the automotive industry for joints under impact; temperature effects in joints typically found in civil engineering; and advanced nondestructive techniques such as terahertz spectroscopy to assess the durability of adhesive joints. Providing a review of the state-of the art in industrial applications of adhesives, the book serves as a valuable reference resource for researchers and graduate students interested in adhesive bonding.
Download or read book Plasma Spray Coating written by Robert B. Heimann and published by John Wiley & Sons. This book was released on 2008-07-11 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past two decades, thermal spraying of metallic, ceramic and composite coatings has emerged as a powerful tool for surface engineering, with many new applications and markets continually being developed. This book will help materials scientists and engineers to choose the most appropriate combination of materials, equipment, and operation parameters for the design of high-performance coatings with new functional properties and improved service life. Includes: * a thorough treatment of the fundamental physical processes governing plasma spray technology; * a critical assessment of advantages and disadvantages of the method compared with other suface coating techniques; * a discussion of basic equipment requirements and limitations; * case studies and typical applications to solve industrial problems. Plasma-Spray Coating offers a stimulating combination of basic concepts and practical applications. Materials scientists and engineers, as well as graduate students will find this book of enormous value.
Download or read book Determination of Mechanical Properties of Adhesives for Use in the Design of Bonded Joints written by Edward W. Kuenzi and published by . This book was released on 1963 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
