Download or read book Evaluation of High Pressure Components of Fuel Injection Systems Using Speckle Interferometry written by Adis Basara and published by . This book was released on 2007 with total page 213 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Materials for High Pressure Fuel Injection Systems written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The high-level goal of this multi-year effort was to facilitate the Advanced Combustion Engine goal of 20% improvement (compared to 2009 baseline) of commercial engine efficiency by 2015. A sub-goal is to increase the reliability of diesel fuel injectors by investigating modelbased scenarios that cannot be achieved by empirical, trial and error methodologies alone. During this three-year project, ORNL developed the methodology to evaluate origins and to record the initiation and propagation of fatigue cracks emanating from holes that were electrodischarge machined (EDM), the method used to form spray holes in fuel injector tips. Both x-ray and neutron-based methods for measuring residual stress at four different research facilities were evaluated to determine which, if any, was most applicable to the fuel injector tip geometry. Owing to the shape and small volumes of material involved in the sack area, residual stress data could only be obtained in the walls of the nozzle a few millimeters back from the tip, and there was a hint of only a small compressive stress. This result was consistent with prior studies by Caterpillar. Residual stress studies were suspended after the second year, reserving the possibility of pursuing this in the future, if and when methodology suitable for injector sacks becomes available. The smooth specimen fatigue behavior of current fuel injector steel materials was evaluated and displayed a dual mode initiation behavior. At high stresses, cracks started at machining flaws in the surface; however, below a critical threshold stress of approximately 800 MPa, cracks initiated in the bulk microstructure, below the surface. This suggests that for the next generation for high-pressure fuel injector nozzles, it becomes increasingly important to control the machining and finishing processes, especially if the stress in the tip approaches or exceeds that threshold level. Fatigue tests were also conducted using EDM notches in the gage sections. Compared to the smooth specimens, EDM notching led to a severe reduction in total fatigue life. A reduction in fatigue life of nearly four orders of magnitude can occur at an EDM notch the approximate size of fuel injector spray holes. Consequently, the initiation and propagation behavior of cracks from small spray holes is relevant for generation of design quality data for the next generation diesel fuel injection devices. This is especially true since the current design methodologies usually rely on the less conservative smooth specimen fatigue testing results, and since different materials can have varying levels of notch fatigue resistance.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1978 with total page 1018 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fuel Injector Patternation Evaluation in Advanced Liquid Fueled High Pressure Gas Turbine Combustors Using Nonintrusive Optical Diagnostic Techniques written by and published by . This book was released on 1998 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1987 with total page 936 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Annual Index abstracts of SAE Technical Papers written by and published by . This book was released on 1998 with total page 772 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 1032 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Technical Literature Abstracts written by Society of Automotive Engineers and published by . This book was released on 1999 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied mechanics reviews written by and published by . This book was released on 1948 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Conference Papers Index written by and published by . This book was released on 1987 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: Monthly. Papers presented at recent meeting held all over the world by scientific, technical, engineering and medical groups. Sources are meeting programs and abstract publications, as well as questionnaires. Arranged under 17 subject sections, 7 of direct interest to the life scientist. Full programs of meetings listed under sections. Entry gives citation number, paper title, name, mailing address, and any ordering number assigned. Quarterly and annual indexes to subjects, authors, and programs (not available in monthly issues).
Download or read book Metals Abstracts written by and published by . This book was released on 1994 with total page 1584 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the Institution of Mechanical Engineers written by and published by . This book was released on 1992 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Current Research in Britain written by and published by . This book was released on 1985 with total page 1234 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Highway Safety Literature written by and published by . This book was released on with total page 820 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book R D Abstracts written by Technology Reports Centre (Great Britain) and published by . This book was released on 1979 with total page 732 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Optical Measurements written by Franz Mayinger and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt: Increasing possibilities of computer-aided data processing have caused a new revival of optical techniques in many areas of mechanical and chemical en gineering. Optical methods have a long tradition in heat and mass transfer and in fluid dynamics. Global experimental information is not sufficient for developing constitution equations to describe complicated phenomena in fluid dynamics or in transfer processes by a computer program . Furthermore, a detailed insight with high local and temporal resolution into the thermo-and fluiddynamic situations is necessary. Sets of equations for computer program in thermo dynamics and fluid dynamics usually consist of two types of formulations: a first one derived from the conservation laws for mass, energy and momentum, and a second one mathematically modelling transport processes like laminar or turbulent diffusion. For reliably predicting the heat transfer, for example, the velocity and temperature field in the boundary layer must be known, or a physically realistic and widely valid correlation describing the turbulence must be avail able. For a better understanding of combustion processes it is necessary to know the local concentration and temperature just ahead of the flame and in the ignition zone.
Download or read book Announcement of Highway Safety Literature written by and published by . This book was released on 1983 with total page 832 pages. Available in PDF, EPUB and Kindle. Book excerpt:
