Download or read book Evaluation of Film Cooling Superposition Method on the Suction Side of a Blade Model written by Christopher Yoon and published by . This book was released on 2018 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: Film cooling is often used for turbine airfoil cooling, and there are numerous studies of the performance of a single row of holes. Typically, blades and vanes in gas turbine engines have multiple rows of holes that interact. Consequently, there is a need to develop techniques to predict film cooling performance with multiple rows of holes. One of the method is to superposition single row cooling effectiveness to predict combined effectiveness. Although there have been many studies of superposition techniques with multiple rows of cylindrical holes, there have been very few in which shaped holes were used with a typical turbine airfoil model. In this study, film effectiveness was measured on the suction side of a turbine blade model using two rows of 7-7-7 shaped holes, with pitch to diameter ratio of 6, and the two rows were more than 40 diameters apart. Measurements were made with each row operating independently, which provided the experimental data for superposition predictions. These predictions were evaluated with effectiveness measurements with both rows operational. For these combined row tests, two different upstream blowing ratios and a wide range of downstream blowing ratios were selected. The superposition predictions were reasonably accurate when the upstream blowing ratio was high with a corresponding smaller film effectiveness downstream (due to jet separation). However, when the upstream coolant holes were operated at optimum blowing ratio with maximum film effectiveness downstream, the superposition analysis predicted film effectiveness levels slightly lower than actual levels. These results indicate that there was an interaction between jets that resulted in higher film effectiveness than what the superposition method had predicted

Download or read book Experimental Study of Gas Turbine Blade Film Cooling and Internal Turbulated Heat Transfer at Large Reynolds Numbers written by Shantanu Mhetras and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Film cooling effectiveness on a gas turbine blade tip on the near tip pressure side and on the squealer cavity floor is investigated. Optimal arrangement of film cooling holes, effect of a full squealer and a cutback squealer, varying blowing ratios and squealer cavity depth are also examined on film cooling effectiveness. The film-cooling effectiveness distributions are measured on the blade tip, near tip pressure side and the inner pressure and suction side rim walls using a Pressure Sensitive Paint (PSP) technique. A blowing ratio of 1.0 is found to give best results on the pressure side whereas the other tip surfaces give best results for blowing ratios of 2. Film cooling effectiveness tests are also performed on the span of a fully-cooled high pressure turbine blade in a 5 bladed linear cascade using the PSP technique. Film cooling effectiveness over the entire blade region is determined from full coverage film cooling, showerhead cooling and from each individual row with and without an upstream wake. The effect of superposition of film cooling effectiveness from each individual row is then compared with full coverage film cooling. Results show that an upstream wake can result in lower film cooling effectiveness on the blade. Effectiveness magnitudes from superposition of effectiveness data from individual rows are comparable with that from full coverage film cooling. Internal heat transfer measurements are also performed in a high aspect ratio channel and from jet array impingement on a turbulated target wall at large Reynolds numbers. For the channel, three dimple and one discrete rib configurations are tested on one of the wide walls for Reynolds numbers up to 1.3 million. The presence of a turbulated wall and its effect on heat transfer enhancement against a smooth surface is investigated. Heat transfer enhancement is found to decrease at high Re with the discrete rib configurations providing the best enhancement but highest pressure losses. Experiments to investigate heat transfer and pressure loss from jet array impingement are also performed on the target wall at Reynolds numbers up to 450,000. The heat transfer from a turbulated target wall and two jet plates is investigated. A target wall with short pins provides the best heat transfer with the dimpled target wall giving the lowest heat transfer among the three geometries studied.

Download or read book Effect of Film Hole Shape on Turbine Blade Film Cooling Performance written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-05-30 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt: The detailed heat transfer coefficient and film cooling effectiveness distributions as well as tile detailed coolant jet temperature profiles on the suction side of a gas turbine blade A,ere measured using a transient liquid crystal image method and a traversing cold wire and a traversing thermocouple probe, respectively. The blade has only one row of film holes near the gill hole portion on the suction side of the blade. The hole geometries studied include standard cylindrical holes and holes with diffuser shaped exit portion (i.e. fanshaped holes and laidback fanshaped holes). Tests were performed on a five-blade linear cascade in a low-speed wind tunnel. The mainstream Reynolds number based on cascade exit velocity was 5.3 x 10(exp 5). Upstream unsteady wakes were simulated using a spoke-wheel type wake generator. The wake Strouhal number was kept at 0 or 0.1. Coolant blowing ratio was varied from 0.4 to 1.2. Results show that both expanded holes have significantly improved thermal protection over the surface downstream of the ejection location, particularly at high blowing ratios. However, the expanded hole injections induce earlier boundary layer transition to turbulence and enhance heat transfer coefficients at the latter part of the blade suction surface. In general, the unsteady wake tends to reduce film cooling effectiveness.Han, J. C. and Teng, S.Glenn Research CenterHEAT TRANSFER COEFFICIENTS; COOLANTS; TEMPERATURE PROFILES; SUCTION; TURBINE BLADES; HEAT MEASUREMENT; FILM COOLING; BOUNDARY LAYER TRANSITION; CASCADE WIND TUNNELS; CYLINDRICAL BODIES; EJECTION; GAS TURBINES; HOLE DISTRIBUTION (MECHANICS); LIQUID CRYSTALS; LOW SPEED; THERMAL PROTECTION; THERMOCOUPLES; WIND TUNNELS

Download or read book Heat Transfer on a Film Cooled Rotating Blade written by Vijay K. Garg and published by . This book was released on 1999 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Advances in Heat Transfer written by and published by Academic Press. This book was released on 2017-11-11 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Heat Transfer, Volume 49 provides in-depth review articles from a broader scope than in traditional journals or texts. Topics covered in this new volume include Heat Transfer in Rotating Cooling Channel, Flow Boiling and Flow Condensation in Reduced Gravity, Advances in Gas Turbine Cooling, and Advanced Heat Transfer Topics in Complex Duct Flows. While the articles in this series will be of great interest to mechanical, chemical and industrial engineers working in the field of heat transfer, the book is also ideal for those in graduate schools or industry, and even non-specialists interested in the latest research. Compiles the expert opinions of leaders in the industry Fills the information gap between regularly scheduled journals and university-level textbooks by providing in-depth review articles over a broader scope than in traditional journals or texts Essential reading for all mechanical, chemical and industrial engineers working in the field of heat transfer, or in graduate schools or industry

Download or read book Paper written by and published by . This book was released on 1999 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Leading Edge Film Cooling Effects on Turbine Blade Heat Transfer written by Vijay K. Garg and published by . This book was released on 1995 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas - June 5-8, 1995.

Download or read book Journal of Heat Transfer written by and published by . This book was released on 2005 with total page 484 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ASME Technical Papers written by and published by . This book was released on 1999 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Blowing Ratio Effects on Film Cooling Effectiveness written by Kuo-Chun Liu and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The research focuses on testing the film cooling effectiveness on a gas turbine blade suction side surface. The test is performed on a five bladed cascade with a blow down facility. Four different blowing ratios are used in this study, which are 0.5, 1.0, 1.6, and 2.0; mainstream flow conditions are maintained at exit Mach number of 0.7, 1.1 and 1.3. Nitrogen is injected as the coolant so that the oxygen concentration levels can be obtained for the test surface. Based on mass transfer analogy, film cooling effectiveness can be computed with pressure sensitive paint (PSP) technique. The effect of blowing ratio on film cooling effectiveness is presented for each testing condition. The spanwise averaged effectiveness for each case is also presented to compare the blowing ratio and mainstream effect on film cooling effectiveness. Results show that due to effects of shock, the optimum blowing ratio is 1.6 for exit Mach number of 1.1 and 1.3; however; without the effects of shock, the optimum blowing ratio is 1.0 for exit Mach number of 0.7.

Download or read book Computational Simulation and Analysis of Film Cooling for the Leading edge Model of a Turbine Blade written by and published by . This book was released on 2007 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of interest is the cooling of turbine blades in large gas combustion engines where hot gases from the combustor cause thermal deterioration of the metal turbine blades. A thin-film of coolant flow buffers the hottest parts of the blade surface. Heat transfer on a bluff body and, subsequently, a single-hole cooling problem is solved numerically in two-dimensions. The flow is assumed to be incompressible, and the laminar, steady Navier-Stokes equations are used to obtain the flow solution. Results for the bluff-body heat transfer agree very well with experimental data up to the separation point, and are within 20% of the data thereafter. The film-cooling simulation yielded higher cooling effectiveness due in large part to the use of the two-dimensional model, which treats the hole as a slot with higher coolant mass. Results from the simulations indicate that the Cobalt flow solver is capable of solving complex heat transfer problems.

Download or read book Modelling and Simulation of Turbulent Heat Transfer written by B. Sundén and published by WIT Press. This book was released on 2005-02-21 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing invaluable information for both graduate researchers and R & D engineers in industry and consultancy, this book focuses on the modelling and simulation of fluid flow and thermal transport phenomena in turbulent convective flows. Its overall objective is to present state-of-the-art knowledge in order to predict turbulent heat transfer processes in fundamental and idealized flows as well as in engineering applications. The chapters, which are invited contributions from some of the most prominent scientists in this field, cover a wide range of topics and follow a unified outline and presentation to aid accessibility.

Download or read book The Influence of Pressure Ratio on Film Cooling Performance of a Turbine Blade written by and published by . This book was released on 1999 with total page 111 pages. Available in PDF, EPUB and Kindle. Book excerpt: The relationship between the plenum to freestream total pressure ratio on film cooling performance is experimentally investigated. Measurements of both the heat transfer coefficient and the adiabatic effectiveness were made on the suction side of the center blade in a linear transonic cascade. Entrance and exit Mach numbers were 0.3 and 1.2 respectively. Reynolds number based on chord and exit conditions is 3 x 10(exp 6). The blade contour is representative of a typical General Electric first Stage, high turning, turbine blade. Tunnel freestream conditions were 10 psig total pressure and approximately 80 deg C. A chilled air coolant film was supplied to a generic General Electric leading edge showerhead coolant scheme. Pressure ratios were varied from run to run over the ranges of 1.02 to 1.20. The density ratio was near a value of 2. A method to determine both the heat transfer coefficient and film cooling effectiveness from experimental data is outlined. Results show that the heat transfer coefficient is independent of the pressure ratio over these ranges of blowing parameters. Also, there is shown to be a weak reduction of film cooling effectiveness with higher pressure ratios. Results are shown for effectiveness and heat transfer coefficient profiles along the blade.

Download or read book Experimental Study of Gas Turbine Blade Film Cooling and Heat Transfer written by Diganta P. Narzary and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern gas turbine engines require higher turbine-entry gas temperature to improve their thermal efficiency and thereby their performance. A major accompanying concern is the heat-up of the turbine components which are already subject to high thermal and mechanical stresses. This heat-up can be reduced by: (i) applying thermal barrier coating (TBC) on the surface, and (ii) providing coolant to the surface by injecting secondary air discharged from the compressor. However, as the bleeding off of compressor discharge air exacts a penalty on engine performance, the cooling functions must be accomplished with the smallest possible secondary air injection. This necessitates a detailed and systematic study of the various flow and geometrical parameters that may have a bearing on the cooling pattern. In the present study, experiments were performed in three regions of a non-rotating gas turbine blade cascade: blade platform, blade span, and blade tip. The blade platform and blade span studies were carried out on a high pressure turbine rotor blade cascade in medium flow conditions. Film-cooling effectiveness or degree of cooling was assessed in terms of cooling hole geometry, blowing ratio, freestream turbulence, coolant-to-mainstream density ratio, purge flow rate, upstream vortex for blade platform cooling and blowing ratio, and upstream vortex for blade span cooling. The blade tip study was performed in a blow-down flow loop in a transonic flow environment. The degree of cooling was assessed in terms of blowing ratio and tip clearance. Limited heat transfer coefficient measurements were also carried out. Mainstream pressure loss was also measured for blade platform and blade tip film-cooling with the help of pitot-static probes. The pressure sensitive paint (PSP) and temperature sensitive paint (TSP) techniques were used for measuring film-cooling effectiveness whereas for heat transfer coefficient measurement, temperature sensitive paint (TSP) technique was employed. Results indicated that the blade platform cooling requires a combination of upstream purge flow and downstream discrete film-cooling holes to cool the entire platform. The shaped cooling holes provided wider film coverage and higher film-cooling effectiveness than the cylindrical holes while also creating lesser mainstream pressure losses. Higher coolant-to-mainstream density ratio resulted in higher effectiveness levels from the cooling holes. On the blade span, at any given blowing ratio, the suction side showed better coolant coverage than the pressure side even though the former had two fewer rows of holes. Film-cooling effectiveness increased with blowing ratio on both sides of the blade. Whereas the pressure side effectiveness continued to increase with blowing ratio, the increase in suction side effectiveness slowed down at higher blowing ratios (M=0.9 and 1.2). Upstream wake had a detrimental effect on film coverage. 0% and 25% wake phase positions significantly decreased film-cooling effectiveness magnitude. Comparison between the compound shaped hole and the compound cylindrical hole design showed higher effectiveness values for shaped holes on the suction side. The cylindrical holes performed marginally better in the curved portion of the pressure side. Finally, the concept tip proved to be better than the baseline tip in terms of reducing mainstream flow leakage and mainstream pressure loss. The film-cooling effectiveness on the concept blade increased with increasing blowing ratio and tip gap. However, the film-coverage on the leading tip portion was almost negligible.

Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.

Download or read book Dissertation Abstracts International written by and published by . This book was released on 2007 with total page 854 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Heat Transfer in Gas Turbine Systems written by Richard J. Goldstein and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explores recent developments in heat transfer and thermal control applied to modern high-temperature gas turbine systems. It examines experimental results and techniques computational studies and methods and design recommendations. Aspects of heat transfer in rotating machinery are studied as well as thermal aspects of other sections of the turbine (e.g. the compressor). Proceedings of an August 2000 conference.