Download or read book Evaluation of Dynamic Speed Display Signs DSDS written by Elisabeth R. Rose and published by . This book was released on 2003 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dynamic speed display signs (DSDS), devices that detect and display a vehicle's current speed back to the driver, have been shown to have a significant speed-reducing effect in temporary applications such as work zones or neighborhood speed watch programs. In this report, researchers examined the effectiveness of DSDS installed permanently in several locations that were experiencing speed-related problems. Seven sites were evaluated, including a school speed zone, two transition speed zones in advance of a school speed zone, two sharp horizontal curves and two approaches to signalized intersections on high-speed roadways. Data were collected before the DSDS were installed, about one week after installation to determine initial effects of the signs upon vehicle speeds, and again about four months after installation to determine how well the initial speed reductions were maintained. Researchers analyzed average speeds, 85th percentile speeds, percent of the sample exceeding the speed limit and standard deviations of the samples. Also, least square regression analyses between the speed of a vehicle upstream of the DSDS and that vehicle's speed measured again at the DSDS were performed to determine whether the sign affected higher speed vehicles more than lower speed vehicles. Overall, average speeds were reduced by 9 miles per hour at the school speed zone. Elsewhere, the effect of the DSDS was less dramatic, with average speeds reduced by 5 mph or less, depending on the location tested. As expected, the influence of a DSDS was found to differ depending on how fast a motorist approached the DSDS. Those motorists traveling faster than the posted speed did appear to reduce their speed more significantly in response to the DSDS than did motorists traveling at or below the posted speed limit. The results of this project suggest that DSDS can be effective at reducing speeds in permanent applications if appropriate site conditions apply.

Download or read book Offset Right turn Lanes for Improved Intersection Sight Distance written by Karen S. Schurr and published by . This book was released on 2010 with total page 142 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Behavioural Adaptation and Road Safety written by Christina Rudin-Brown and published by CRC Press. This book was released on 2013-05-24 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: Despite being an accepted construct in traffic and transport psychology, the precise nature of behavioural adaptation, including its causes and consequences, has not yet been established within the road safety community. A comprehensive collection of recent literature, Behavioural Adaptation and Road Safety: Theory, Evidence, and Action explores behavioural adaptation in road users. It examines behavioural adaptation within the context of historical and theoretical perspectives, and puts forth tangible—and practical—solutions that can effectively address adverse behavioural adaptation to road safety interventions before it occurs. Edited by Christina Rudin-Brown and Samantha Jamson, with chapters authored by leading road safety experts in driver psychology and behaviour, the book introduces the concept of behavioural adaptation and details its more relevant issues. It reviews the definition of behavioural adaptation that was put forward by the OECD in 1990 and then puts this definition through its paces, identifying where it may be lacking and how it might be improved. This sets the context for the remaining chapters which take the OECD definition as their starting points. The book discusses the various theories and models of behavioural adaptation and more general theories of driver behaviour developed during the last half century. It provides examples of the "evidence" for behavioural adaptation—instances in which behavioural adaptation arose as a consequence of the introduction of safety countermeasures. The book then focuses on the internal, "human" element and considers countermeasures that might be used to limit the development of behavioural adaptation in various road user groups. The book concludes with practical tools and methodologies to address behavioural adaptation in research and design, and to limit the potential negative effects before they happen. Supplying easy-to-understand, accessible solutions that can be implemented early on in a road safety intervention’s design or conception phase, the chapters represent the most extensive compilation of literature relating to behavioural adaptation and its consequences since the 1990 OECD report. The book brings together earlier theories of behavioural adaptation with more recent theories in the area and combines them with practical advice, methods, and tangible solutions that can minimise the potential negative impact of behavioural adaptation on road user safety and address it before it occurs. It is an essential component of any road safety library, and should be of particular relevance to researchers, practitioners, designers, and policymakers who are interested in maximizing safety while at the same time encouraging innovation and excellence in road transport-related design.

Download or read book Speed Management written by European Conference of Ministers of Transport and published by OECD Publishing. This book was released on 2006-10-13 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt: Speeding is the number one road safety problem in a large number of OECD/ECMT countries. It is responsible for around one third of the current, unacceptably high levels of road fatalities. Speeding has an impact not only on accidents but also on the ...

Download or read book Modern Robotics written by Kevin M. Lynch and published by Cambridge University Press. This book was released on 2017-05-25 with total page 545 pages. Available in PDF, EPUB and Kindle. Book excerpt: A modern and unified treatment of the mechanics, planning, and control of robots, suitable for a first course in robotics.

Download or read book Strategies for Work Zone Transportation Management Plans written by Leverson Boodlal and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the ways a state department of transportation or other transportation agency can address work zone safety and other impacts is to develop and implement a Transportation Management Plan (TMP). The TRB National Cooperative Highway Research Program's NCHRP Research Report 945: Strategies for Work Zone Transportation Management Plans provides a practitioner-ready guidebook on how to select and implement strategies that improve safety and traffic operations in roadway construction work zones. Supplemental materials to the report include NCHRP Web-Only Document 276: Evaluating Strategies for Work ZoneTransportation Management Plans; fact sheets on ramp meter, reversible lane, and truck restrictions; and guidebook appendices.

Download or read book Handbook of Sports Medicine and Science written by Margo Mountjoy and published by John Wiley & Sons. This book was released on 2014-10-06 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new International Olympic Committee (IOC) handbook covers the science, medicine and psycho-social aspects of females in sports at all levels of competition. Each chapter focuses on the specific issues that female athletes confront both on and off the field, such as bone health, nutritional recommendations, exercise/competition during menstruation and pregnancy, and much more. Fully endorsed by the IOC and drawing upon the experience of an international team of expert contributors, no other publication deals with the topic in such a concise and complete manner. The Female Athlete is recommended for all health care providers for women and girl athletes internationally for all sports and all levels of competition. It is a valuable resource for medical doctors, physical and occupational therapists, nutritionists, and sports scientists as well as coaches, personal trainers and athletes.

Download or read book Textbook of Plastic and Reconstructive Surgery written by Deepak K. Kalaskar and published by UCL Press. This book was released on 2016-08-02 with total page 491 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by experts from London’s renowned Royal Free Hospital, Textbook of Plastic and Reconstructive Surgery offers a comprehensive overview of the vast topic of reconstructive plastic surgery and its various subspecialties for introductory plastic surgery and surgical science courses. The book comprises five sections covering the fundamental principles of plastic surgery, cancer, burns and trauma, paediatric plastic surgery and aesthetic surgery, and covers the breadth of knowledge that students need to further their career in this exciting field. Additional coverage of areas in which reconstructive surgery techniques are called upon includes abdominal wall reconstruction, ear reconstruction and genital reconstruction. A chapter on aesthetic surgery includes facial aesthetic surgery and blepharoplasty, aesthetic breast surgery, body contouring and the evolution of hair transplantation.The broad scope of this volume and attention to often neglected specialisms such as military plastic surgery make this a unique contribution to the field. Heavily illustrated throughout, Textbook of Plastic and Reconstructive Surgery is essential reading for anyone interested in furthering their knowledge of this exciting field. This book was produced as part of JISC's Institution as e-Textbook Publisher project. Find out more at https://www.jisc.ac.uk/rd/projects/institution-as-e-textbook-publisher

Download or read book Smart Solutions in Today s Transport written by Jerzy Mikulski and published by Springer. This book was released on 2017-09-08 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the thoroughly refereed proceedings of the 17th International Conference on Transport Systems Telematics, TST 2017, held in Katowice-Ustrón, Poland, in April 2017. The 40 full papers presented in this volume were carefully reviewed and selected from 128 submissions. They present and organize the knowledge from within the field of intelligent transportation systems, the specific solutions applied in it and their influence on improving efficiency of transport systems.

Download or read book Semiconductor Laser Engineering Reliability and Diagnostics written by Peter W. Epperlein and published by John Wiley & Sons. This book was released on 2013-03-18 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference book provides a fully integrated novel approach to the development of high-power, single-transverse mode, edge-emitting diode lasers by addressing the complementary topics of device engineering, reliability engineering and device diagnostics in the same book, and thus closes the gap in the current book literature. Diode laser fundamentals are discussed, followed by an elaborate discussion of problem-oriented design guidelines and techniques, and by a systematic treatment of the origins of laser degradation and a thorough exploration of the engineering means to enhance the optical strength of the laser. Stability criteria of critical laser characteristics and key laser robustness factors are discussed along with clear design considerations in the context of reliability engineering approaches and models, and typical programs for reliability tests and laser product qualifications. Novel, advanced diagnostic methods are reviewed to discuss, for the first time in detail in book literature, performance- and reliability-impacting factors such as temperature, stress and material instabilities. Further key features include: practical design guidelines that consider also reliability related effects, key laser robustness factors, basic laser fabrication and packaging issues; detailed discussion of diagnostic investigations of diode lasers, the fundamentals of the applied approaches and techniques, many of them pioneered by the author to be fit-for-purpose and novel in the application; systematic insight into laser degradation modes such as catastrophic optical damage, and a wide range of technologies to increase the optical strength of diode lasers; coverage of basic concepts and techniques of laser reliability engineering with details on a standard commercial high power laser reliability test program. Semiconductor Laser Engineering, Reliability and Diagnostics reflects the extensive expertise of the author in the diode laser field both as a top scientific researcher as well as a key developer of high-power highly reliable devices. With invaluable practical advice, this new reference book is suited to practising researchers in diode laser technologies, and to postgraduate engineering students. Dr. Peter W. Epperlein is Technology Consultant with his own semiconductor technology consulting business Pwe-PhotonicsElectronics-IssueResolution in the UK. He looks back at a thirty years career in cutting edge photonics and electronics industries with focus on emerging technologies, both in global and start-up companies, including IBM, Hewlett-Packard, Agilent Technologies, Philips/NXP, Essient Photonics and IBM/JDSU Laser Enterprise. He holds Pre-Dipl. (B.Sc.), Dipl. Phys. (M.Sc.) and Dr. rer. nat. (Ph.D.) degrees in physics, magna cum laude, from the University of Stuttgart, Germany. Dr. Epperlein is an internationally recognized expert in compound semiconductor and diode laser technologies. He has accomplished R&D in many device areas such as semiconductor lasers, LEDs, optical modulators, quantum well devices, resonant tunneling devices, FETs, and superconducting tunnel junctions and integrated circuits. His pioneering work on sophisticated diagnostic research has led to many world’s first reports and has been adopted by other researchers in academia and industry. He authored more than seventy peer-reviewed journal papers, published more than ten invention disclosures in the IBM Technical Disclosure Bulletin, has served as reviewer of numerous proposals for publication in technical journals, and has won five IBM Research Division Awards. His key achievements include the design and fabrication of high-power, highly reliable, single mode diode lasers. Book Reviews “Semiconductor Laser Engineering, Reliability and Diagnostics: A Practical Approach to High Power and Single Mode Devices”. By Peter W. Epperlein Prof. em. Dr. Heinz Jäckel, High Speed Electronics and Photonics, Swiss Federal Institute of Technology ETH Zürich, Switzerland The book “Semiconductor Laser Engineering, Reliability and Diagnostics” by Dr. P.W. Epperlein is a landmark in the recent literature on semiconductor lasers because it fills a longstanding gap between many excellent books on laser theory and the complex and challenging endeavor to fabricate these devices reproducibly and reliably in an industrial, real world environment. Having worked myself in the early research and development of high power semiconductor lasers, I appreciate the competent, complete and skillful presentation of these three highly interrelated topics, where small effects have dramatic consequences on the success of a final product, on the ultimate performance and on the stringent reliability requirements, which are the name of the game. As the title suggests the author addresses three tightly interwoven and critical topics of state-of-the-art power laser research. The three parts are: device and mode stability engineering (chapter 1, 2), reliability mechanisms and reliability assessment strategies (chapter 3, 4, 5, 6) and finally material and device diagnostics (chapter 7, 8, 9) all treated with a strong focus on the implementation. This emphasis on the complex practical aspects for a large-scale power laser fabrication is a true highlight of the book. The subtle interplay between laser design, reliability strategies, advanced failure analysis and characterization techniques are elaborated in a very rigorous and scientific way using a very clear and easy to read representation of the complex interrelation of the three major topics. I will abstain from trying to provide a complete account of all the topics but mainly concentrate on the numerous highlights. The first part 1 “Laser Engineering” is divided in two chapters on basic electronic-optical, structural, material and resonator laser engineering on the one side, and on single mode control and stability at very high, still reliable power-levels with the trade-off between mirror damage, single mode stability on the other side. To round up the picture less well-known concepts and the state-of-the-art of large-area lasers, which can be forced into single-mode operation, are reviewed carefully. The subtle and complex interplay, which is challenging to optimize for a design for reliability and low stress as a major boundary condition is crucial for the design. The section gives a rather complete and well-referenced account of all relevant aspects, relations and trade-offs for understanding the rest of the book. The completeness of the presentation on power laser diode design based on basic physical and plausible arguments is mainly based on analytic mathematical relations as well as experiments providing a new and well-balanced addition for the power diode laser literature in particular. Modern 2D self-consistent electro-optical laser modeling including carrier hole burning and thermal effects – this is important because the weak optical guiding and gain-discrimination depend critically on rather small quantities and effects, which are difficult to optimize experimentally – is used in the book for simulation results, but is not treated separately. The novel and really original, “gap-filling” bulk of the book is elaborated by the author in a very clear way in the following four chapters in the part 2 “Laser Reliability” on laser degradation physics and mirror design and passivation at high power, followed then by two very application oriented chapters on reliability design engineering and practical reliability strategies and implementation procedures. This original combination of integral design and reliability aspects – which are mostly neglected in standard literature – is certainly a major plus of this book. I liked this second section as a whole, because it provides excellent insights in degradation physics on a high level and combines it in an interesting and skillful way with the less “glamorous” (unfortunately) but highly relevant reliability science and testing strategies, which is particularly important for devices operating at extreme optical stresses with challenging lifetime requirements in a real word environment. Finally, the last part 3 “Laser Diagnostics” comprising three chapters, is devoted mainly to advanced experimental diagnostics techniques for material integrity, mechanical stress, deep level defects, various dynamic laser degradation effects, surface- and interface quality, and most importantly heating and disordering of mirrors and mirror coatings. The topics of characterization techniques comprising micro-Raman- and micro-thermoreflectance-probing, 2K photoluminescence spectroscopy, micro-electroluminescence and photoluminescence scanning, and deep-level-transient spectroscopy have been pioneered by the author for the specific applications over many years guaranteeing many competent and well represented insights. These techniques are brilliantly discussed and the information distributed in many articles by the author has been successfully unified in a book form. In my personal judgment and liking, I consider the parts 2 and 3 on reliability and diagnostics as the most valuable and true novel contribution of the book, which in combination with the extremely well-covered laser design of part 1 clearly fill the gap in the current diode laser literature, which in this detail has certainly been neglected in the past. In summary, I can highly recommend this excellent, well-organized and clearly written book to readers who are already familiar with basic diode laser theory and who are active in the academic and industrial fabrication and characterization of semiconductor lasers. Due to its completeness, it also serves as an excellent reference of the current state-of-the-art in reliability engineering and device and material diagnostics. Needless to mention that the quality of the book, its representations and methodical structure meet the highest expectation and are certainly a tribute from the long and broad experience of the author in academic laser science and the industrial commercialization of high power diode lasers. In my opinion, this book was a pleasure to read and due to its quality and relevance deserves a large audience in the power diode laser community! Prof. em. Dr. Heinz Jäckel, High Speed Electronics and Photonics, Swiss Federal Institute of Technology ETH Zürich, Switzerland June 16, 2013 ========================================== “Semiconductor Laser Engineering, Reliability and Diagnostics: A Practical Approach to High Power and Single Mode Devices”. By Peter W. Epperlein Dr. Chung-en Zah, Research Director, Semiconductor Technologies Research, S&T Division, Corning Incorporate, Corning NY, USA This book covers for the first time the three closely interrelated key laser areas of engineering (design), reliability and diagnostics in one book, written by the well-known practitioner in cutting-edge optoelectronics industries, Dr. Peter W. Epperlein. The book closes the gap in the current book literature and is thus a unique and excellent example of how to merge design, reliability and diagnostics aspects in a very professional, profound and complete manner. All physical and technological principles, concepts and practical aspects required for developing and fabricating highly-reliable high-power single-mode laser products are precisely specified and skilfully formulated along with all the necessary equations, figures, tables and worked-out examples making it easy to follow through the nine chapters. Hence, this unique book is a milestone in the diode laser literature and is an excellent reference book not only for diode laser researchers and engineers, but also diode laser users. The engineering part starts with a very informative and clear, well-presented account of all necessary basic diode laser types, principles, parameters and characteristics for an easy and quick understanding of laser functionality within the context of the book. Along with an elaborate and broad discussion of relevant laser material systems, applications, typical output powers, power-limiting factors and reliability tradeoffs, basic fabrication and packaging technologies, this excellent introductory section is well suited to become quickly and easily familiar with practical aspects and issues of diode laser technologies. Of special importance and high usefulness is the first analytic and quantitative discussion in a book on issues of coupling laser power into optical single mode fibers. The second section discusses in a well-balanced, competent and skilful way waveguide topics such as basic high-power design approaches, transverse vertical and lateral waveguide concepts, stability of the fundamental transverse lateral mode and fundamental mode waveguide optimization techniques by considering detrimental effects such as heating, carrier injection, spatial hole burning, lateral current spreading and gain profile variations. Less well-known approaches to force large-area lasers into a single mode operation are well-identified and carefully discussed in depth and breadth. All these topics are elaborated in a very complete, rigorous and scientific way and are clearly articulated and easy to read. In particular, the book works out the complex interaction between the many different effects to optimize high-power single-mode performance at ultimate reliability and thus is of great benefit to every researcher and engineer engaged in this diode laser field. Another novelty and highlight is, for the first time ever in book form, a comprehensive yet concise discussion of diode laser reliability related issues. These are elaborated in four distinct chapters comprising laser degradation physics and modes, optical strength enhancement approaches including mirror passivation/coating and non-absorbing mirror technologies, followed by two highly relevant product-oriented chapters on reliability design engineering concepts and techniques and an elaborate reliability test plan for laser chip and module product qualification. This original and novel approach to link laser design to reliability aspects and requirements provides both, most useful insight into degradation processes such as catastrophic optical mirror damage on a microscopic scale, and a wide selection of effective remedial actions. These accounts, which are of highest significance for lasers operating at the optical stress limit due to extremely high output power densities and most demanding lifetime requirements are very professionally prepared and discussed in an interesting, coherent and skilful manner. The diagnostics part, consisting of three very elaborate chapters, is most unique and novel with respect to other diode laser books. It discusses for the first time ever on a very high level and in a competent way studies on material integrity, impurity trapping effects, mirror and cavity temperatures, surface- and interface quality, mirror facet disorder effects, mechanical stress and facet coating instability, and diverse laser temperature effects, dynamic laser degradation effects and mirror temperature maps. Of highest significance to design, performance and reliability are the various correlations established between laser device and material parameters. The most different and sophisticated experiments, carried out by the author at micrometer spatial resolutions and at temperatures as low as 2K, provide highly valuable insights into laser and material quality parameters, and reveal for the first time the origins of high power limitations on an atomic scale due to local heating effects and deep level defects. It is of great benefit, that the experimental techniques such as Raman spectroscopy, various luminescence techniques, thermoreflectance and deep-level transient spectroscopy, pioneered by the author for the specific experiments on lasers, are discussed with great expertise in depth and breadth, and the numerous paper articles published by the author are now represented in this book. The book has an elaborate table of contents and index, which are very useful, over 200 illustrative figures and tables, and extensive lists of references to all technical topics at the end of each of the nine chapters, which make it easy to follow from cover to cover or by jumping in at random areas of special interest. Moreover, experimental and theoretical concepts are always illustrated by practical examples and data. I can highly recommend this extremely relevant, well-structured and well-formulated book to all practising researchers in industrial and academic diode laser R&D environments and to post-graduate engineering students interested in the actual problems of designing, manufacturing, testing, characterising and qualifying diode lasers. Due to its completeness and novel approach to combine design, reliability and diagnostics in the same book, it can serve as an ideal reference book as well, and it deserves to be welcomed wordwide by the addressed audience. Dr. Chung-en Zah, Research Director, Semiconductor Technologies Research, S&T Division, Corning Incorporate, Corning NY, USA =========================================== “Semiconductor Laser Engineering, Reliability and Diagnostics: A Practical Approach to High Power and Single Mode Devices”. By Peter W. Epperlein Cordinatore Prof. Lorenzo Pavesi, UNIVERSITÀ DEGLI STUDI DI TRENTO, Dipartimento di Fisica / Laboratorio di Nanoscienze This book represents a well thought description of three fundamental aspects of laser technology: the functioning principles, the reliability and the diagnostics. From this point of view, and, as far as I know, this is a unique example of a book where all these aspects are merged together resulting in a well-balanced presentation. This helps the reader to move with ease between different concepts since they are presented in a coherent manner and with the same terminology, symbols and definitions. The book reads well. Despite the subtitle indicates that it is a practical approach, the book is also correct from a formal point of view and presents the necessary equations and derivations to understand both the physical mechanisms and the practicalities via a set of useful formulas. In addition, there is the more important aspect of many real-life examples of how a laser is actually manufactured and which the relevant parameters that determine its behaviour are. It impresses the amounts of information that are given in the book: this would be more typical of a thick handbook on semiconductor laser than of an agile book. Dr. Epperlein was able to identify the most important concepts and to present them in a clear though concise way. I am teaching a course on Optoelectronics and I'm going to advise students to refer to this book, because it has all the necessary concepts and derivations for a systematic understanding of semiconductor lasers with many worked-out examples, which will help the student to grasp the actual problems of designing, manufacturing, testing and using semiconductor lasers. All the various concepts are joined to very useful figures, which, if provided to instructors as files, can be a useful add-on for the use of the book as text for teaching. Concepts are always detailed with numbers to give a feeling of their practical use. In conclusion, I do find the book suitable for my teaching duties and will refer it to my students. Prof. Dr. Lorenzo Pavesi, Head of the Department of Physics, Head of the Nanoscience Laboratory, University of Trento, Italy 31 May 2013 =========================================== “Semiconductor Laser Engineering, Reliability and Diagnostics: A Practical Approach to High Power and Single Mode Devices”. By Peter W. Epperlein Robert W. Herrick, Ph.D., Senior Component Reliability Engineer, Intel Corp., Santa Clara, California, USA Dr. Epperlein has done the semiconductor laser community a great service, by releasing the most complete book on the market on the practical issues of how to make reliable semiconductor lasers. While dozens of books have been written over the past couple of decades on semiconductor laser design, only a handful have been written on semiconductor laser reliability. Prior to the release of this book, perhaps 40% of the material could be obtained elsewhere by combining five books: one on laser design, one on laser reliability, one on reliability calculations, and a couple of laser review books. Another 40% could be pieced together by collecting 50 -100 papers on the subjects of laser design, laser fabrication, characterization, and reliability. The remaining 20% have not previously been covered in any comprehensive way. Only the introductory material in the first half of the first chapter has good coverage elsewhere. The large majority of the knowledge in this book is generally held as “trade secret” by those with the expertise in the field, and most of those in the know are not free to discuss. The author was fortunate enough to work for the first half of his career in the IBM research labs, with access to unparalleled resources, and the ability to publish his work without trade secret restrictions. The results are still at the cutting edge of our understanding of semiconductor laser reliability today, and go well beyond the empirical “black box” approach many use of “try everything, and see what works.” The author did a fine job of pulling together material from many disparate fields. Dr. Epperlein has particular expertise in high power single mode semiconductor lasers, and those working on those type of lasers will be especially interested in this book, as there has never been a book published on the fabrication and qualification of such lasers before. But those in almost any field of semiconductor lasers will learn items of interest about device design, fabrication, reliability, and characterization. Unlike most other books, which intend to convey the scientific findings or past work of the author, this one is written more as a “how to” manual, which should make it more accessible and useful to development engineers and researchers in the field. It also has over 200 figures, which make it easier to follow. As with many books of this type, it is not necessary to read it from cover-to-cover; it is best skimmed, with deep diving into any areas of special interest to the reader. The book is remarkable also for how comprehensive it is – even experts will discover something new and useful. Dr. Epperlein’s book is an essential read for anyone looking to develop semiconductor lasers for anything other than pure research use, and I give it my highest recommendation. Robert W. Herrick, Ph.D., Senior Component Reliability Engineer, Intel Corp., Santa Clara, California, USA

Download or read book Lifeguarding Manual written by American National Red Cross and published by . This book was released on 2023-12-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Illustrated Textbook of Paediatrics written by Tom Lissauer and published by Elsevier Health Sciences. This book was released on 2017-02-09 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thoroughly revised and updated, the fifth edition of this prize-winning title retains the high level of illustration and accessibility that has made it so popular worldwide with medical students and trainees approaching clinical specialty exams. Illustrated Textbook of Paediatrics has been translated into eight languages over its life. Case studies. Summary boxes. Tips for patient education. Highly illustrated with 100s of colour images. Diseases consistently presented by Clinical features; Investigations; Management; Prognosis; and, where appropriate, Prevention. Separate chapters on Accidents Child protection Diabetes and endocrinology Inborn Errors of Metabolism New chapter on Global child health New co-editor, Will Carroll, Chair of MRCPCH Theory Examinations.

Download or read book Polymer Solutions written by Iwao Teraoka and published by John Wiley & Sons. This book was released on 2004-04-07 with total page 355 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polymer Solutions: An Introduction to Physical Properties offers a fresh, inclusive approach to teaching the fundamentals of physical polymer science. Students, instructors, and professionals in polymer chemistry, analytical chemistry, organic chemistry, engineering, materials, and textiles will find Iwao Teraoka’s text at once accessible and highly detailed in its treatment of the properties of polymers in the solution phase. Teraoka’s purpose in writing Polymer Solutions is twofold: to familiarize the advanced undergraduate and beginning graduate student with basic concepts, theories, models, and experimental techniques for polymer solutions; and to provide a reference for researchers working in the area of polymer solutions as well as those in charge of chromatographic characterization of polymers. The author’s incorporation of recent advances in the instrumentation of size-exclusion chromatography, the method by which polymers are analyzed, renders the text particularly topical. Subjects discussed include: Real, ideal, Gaussian, semirigid, and branched polymer chains Polymer solutions and thermodynamics Static light scattering of a polymer solution Dynamic light scattering and diffusion of polymers Dynamics of dilute and semidilute polymer solutions Study questions at the end of each chapter not only provide students with the opportunity to test their understanding, but also introduce topics relevant to polymer solutions not included in the main text. With over 250 geometrical model diagrams, Polymer Solutions is a necessary reference for students and for scientists pursuing a broader understanding of polymers.

Download or read book Aerodynamic Drag Mechanisms of Bluff Bodies and Road Vehicles written by Gino Sovran and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: These Proceedings contain the papers and oral discussions presented at the Symposium on AERODYNAMIC DRAG MECHANISMS of Bluff Bodies and Road Vehides held at the General Motors Research Laboratories in Warren, Michigan, on September 27 and 28, 1976. This international, invitational Symposium was the twentieth in an annual series, each one having been in a different technical discipline. The Symposia provide a forum for areas of science and technology that are of timely interest to the Research Laboratories as weIl as the technical community at large, and in which personnel of the Laboratories are actively involved. The Symposia furnish an opportunity for the exchange of ideas and current knowledge between participating research specialists from educational, industrial arid governmental institutions and serve to stimulate future research activity. The present world-wide energy situation makes it highly desirable to reduce the force required to move road vehicles through the atmosphere. A significant amount of the total energy consumed for transportation is expended in overcoming the aerodynamic resistance to motion of these vehicles. Reductions in this aerodynamic drag can therefore have a large impact on ground transportation energy requirements. Although aerodynamic development work on road vehides has been performed for many years, it has not been widely reported or accompanied by much basic research.

Download or read book Industrial Safety Management written by J Maiti and published by Springer. This book was released on 2017-10-30 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edited volume focuses on research conducted in the areas of industrial safety. Chapters are extensions of works presented at the International Conference on Management of Ergonomic Design, Industrial Safety and Healthcare Systems. The book addresses issues such as occupational safety, safety by design, safety analytics and safety management. It is a useful resource for students, researchers, industrial professionals and engineers.

Download or read book Integrating Traffic Signal Performance Measures Into Agency Business Processes written by Christopher Day and published by . This book was released on 2015-12-31 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This report discusses uses of and requirements for performance measures in traffic signal systems facilitated by high-resolution controller event data. Uses of external travel time measurements are also discussed. The discussion is led by a high-level synthesis of the systems engineering concepts for traffic signal control, considering technical and nontechnical aspects of the problem. This is followed by a presentation of the requirements for implementing data collection and processing of the data into signal performance measures. The remaining portion of the report uses an example-oriented approach to show a variety of uses of performance measures for communication and detector system health, quality of local control (including capacity allocation, safety, pedestrian performance, preemption, and advanced control analysis), and quality of progression (including evaluation and optimization).

Download or read book Research on Women s Health written by and published by . This book was released on 1997 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: